Overview | American Power Conversion PD150G6F, PD150L6F guide

Safety

Overview

Save these instructions

This manual contains important instructions that must be followed during installation, operation, and configuration of the InfraStruXure PDU.

Safety symbols used in this manual

Indicates an electrical hazard, which, if not avoided, could result in injury or death.

Electrical

Hazard

Indicates a hazard, which, if not avoided, could result in personal injury or damage to the product or other property.

Warning

Indicates a potential hazard which could result in damage to product or other property.

Caution

Indicates important information.

Note

Indicates a heavy load that should not be lifted without assistance.

Heavy

Indicates a standby state. When in standby, the unit is not operating, but it may still contain hazardous voltage. It is not safe to service until the equipment is disconnected from all sources of electrical power.

Cross-reference symbols used in this manual

Indicates that more information is available on the same subject in a different section of this manual.

Indicates that more information is available on the same subject in a different manual.

See also

150kW InfraStruXure PDU—Operation and Configuration

1

Image 9

American Power Conversion PD150G6F, PD150L6F Overview, Safety symbols used in this manual

Contents

150kW InfraStruXure PDU Page About this Manual Page Contents Operation Customizing and Updating the PDU Product Information Safety symbols used in this manual Cross-reference symbols used in this manualOverview Receiving/moving Installation/maintenance Emergency Power Off EPO Total power off procedure EMI InfraStruXure PDU Components Overview Front view InfraStruXure PDU Front view interior Rear view Rear view interior PDU monitoring unit Left = 43..83 lower right = User connection plate PDU Display Interface Top-level status screens Top-level menu screenNavigating through screens Password-protected screens Load-Meter Screen Power Factor Volt-Meter Screen Input Contacts Contacts ScreenOpen or Closed Relay Outputs Alarm Relay Map How to connect contacts to the PDU monitoring unit Main Input Breakers Screen New Logged Items Alarms ScreenEntire Log Clear Log Config Global AlarmLoading Limits Voltage Limits Alarm Condition Explanation PDU Alarms Panel Screen Branch Ckt LoadingBranch Ckt Limits Panel Configuration Circuit breakers occupying positions 08, 10, and 12 onTop right distribution panel Global Panel Config System Password Config ScreenBeeper Volume Select High , Medium , Low , or Off to adjust Date/Time Input Config Electrical ConfigOutput Config Manufacturer Data Factory Defaults Firmware UpdatesSystem ID Operation How to Apply Power to the System Operation How to Apply Power to the System How to Ensure Total Power Off Page Overview InfraStruXure PDU Management OptionsInfraStruXure Manager Network management interfaces Connect the InfraStruXure PDU to the InfraStruXure Manager Configuring the InfraStruXure Manager Configuring the Network Management Interface Configuration OverviewConnect the InfraStruXure PDU to your network Device IP Configuration Wizard TCP/IP configuration methods Bootp & Dhcp configuration Option 43 = 01 04 31 41 50 43 where 150kW InfraStruXure PDU-Operation and Configuration Local access to the control console Use apc for the User Name and PasswordRemote access to the control console Use apc for both User Name and Password Control consoleChoose Network from the Control Console menu Web interface Snmp FTP and SCP 150kW InfraStruXure PDU-Operation and Configuration Page Customizing and Updating the PDU Important Safety Instructions Breakers PDU Orderable Part List Customizing and Updating the PDU How to Add Circuit Breakers and Power Cables Add a power cable to the PDUAdd a circuit breaker on the PDU Customizing and Updating the PDU Overview How to attach the circuit breaker to the mounting brackets How to connect the sub-feed cable to the circuit breaker ATS 0 ATS 1 ATS Atsen How to connect contacts to the PDU monitoring unit Contact closure 24VAC 24VDC Contact closure is recommended How to Connect an EPO Switch to the PDU and Test the Switch Contact Closure-Normally Open Contact Closure-Normally Closed24VAC/VDC-Normally Open Problem Action Safety warnings From a local computer How to Download Firmware UpdatesPage 150kW InfraStruXure PDU Specifications Physical PD150G6F PD150L6F InfraStruXure Standard Warranty Warranty Product Information Warranty Life-Support Policy APC Three-Phase Systems How to contact APC How to Obtain Service Index SSH Page Page Page 990-1984