Manuals / Aspire Digital / Computer Equipment / Computer Hardware

Aspire Digital M1610, M261 Disconnect the CPU Cooler power-cable from the MB connector, Chapter

Models: M261 M1610

1 80

Download 80 pages 33.8 Kb

Page 58

Image 58

17.Disconnect the CPU Cooler power-cable from the MB connector.

18.Release the memory.

19.Remove the System FAN by releasing the four screws shown then removing the fan from the chassis.

Chapter 3

Page 58

Image 58

Aspire Digital M1610, M261 manual Disconnect the CPU Cooler power-cable from the MB connector, Release the memory, Chapter

Contents

Aspire M1610/Veriton M261 Service GuidePRINTED IN TAIWAN Revision History Copyright DisclaimerSCREEN ConventionsMESSAGES Preface Page Entering Setup Product Information Standard CMOS Features Table of ContentsSystem Specifications Advanced BIOS Features CPU Feature Hard Disk Boot PriorityJumper and Connector Information Machine Disassembly and ReplacementTroubleshooting General Information Before You Begin Disassembly ProcedureChapter System SpecificationsFeatures Operating SystemAudio BIOSIEEE 1394 Reserved Onboard Connector I/O ConnectorRear I/O Connector Power SupplyMainboard Placement ChapterBlock Diagram ChapterAspire M1610 Front Panel The computer’s front panel consists of the followingAspire M1610 Rear Panel Veriton M261 Front Panel The computer’s front panel consists of the followingThe computer’s rear panel consists of the following Veriton M261 Rear PanelChapter System Memory Interface Hardware Specifications and ConfigurationsProcessor Support System ClockSuper I/O - IT8718F SiS 968 MuTIOL 1G Media I/OAudio Sub-Systems - Realtek ALC888SCo-lay ALC888 TSB43AB23PDTG4 Host Controller LAN - Realtek8211BLdefault co-lay 8201CL phyUniversal Serial Bus Expansion SlotsWake-Up Event Power & Power ManagementHardware Monitor Function From ACPI StateSPI Bus default System BIOSLPC Bus System Utilities ChapterEntering Setup The items in the main menu are explained below Save & Exit Setup - Save CMOS value settings to CMOS and exit setupExit Without Saving - Abandon all CMOS value changes and exit setup PC Health Status - This will display the current status of your PCProduct Information 640K Standard CMOS FeaturesBase Memory Extended MemoryOptions ParameterDescription 1.44M, 3.5 - inchIDE Channel 0/1 Master IDE Channel 0/1 Slave The following screen shows the IDE Channel Slave menuSATA Channel 1/2 Master X Typematic Delay Msec Advanced BIOS FeaturesX Typematic Rate chars/sec password prompt appears only when end users NOTE Change these settings only if you are familiar with the chipsetSetting to Off will allows users to use the arrow try to run Setup. System means that a passwordCPU Feature The following screen shows the CPU Features menuHard Disk Boot Priority Advanced Chipset Features The following screen shows the Advanced Chipset Features menu256 MB Internal Graphic ControlX VGA Share Memory Size Graphic Engine ClockIntegrated Peripherals The following screen shows the Integrated Peripherals FeaturesOnboard IDE Device Onboard PCI Device The following screen shows the Onboard PCI Device menuX UR2 Duplex Mode Onboard Super IO DeviceHalf X Day of Month Alarm Power ManagementX Month Alarm X Time hh mm ss Alarmmachine will always power on when connect the AC power using an ATX power supply. When ““instant off” is selectedconnect the AC power. Always off means the machine is ChapterPnP/PCI Configuration PCI Express relative itemsPC Health Status the extreme values spikes of the pulses creates Frequency/Voltage Controlpulses are reduced to flatter curves. If you do not Load Optimized Defaults Set Supervisor/User Password Save & Exit Setup Exit Without Saving Machine Disassembly and Replacement ChapterGeneral Information Before You BeginDisassembly Procedure Aspire M1610/Veriton M261 Disassembly7. Disconnect the Card Reader cable 4. Disconnect the front bezel LED cable5. Disconnect the audio cables 6. Disconnect the USB cable Chapter10. Disconnect the ODD power and data cables 8. Disconnect the PA and PD power-cable from the MB connector9. Disconnect P1 power cable and FDD data cable Chapter12. Disconnect the System Fan power-cable from the MB connector 11. Disconnect the HDD power and data cablesChapter Chapter Front BezelFront Bezel Aspire M161018. Release the memory 17. Disconnect the CPU Cooler power-cable from the MB connectorChapter Chapter Reassembly Procedure Aspire M1610/Veriton M261 Reassembly6. Fit the CPU cooler to the MB and fasten four screws shown 5. Install the MemoryChapter 9. Install the ODD into the chassis and slide the ODD rail to lock it 7. Connect the CPU Cooler power-cable to the MB connector8. Connect the System Fan power-cable to the MB connector 10. Install the FDD and slide the FDD rail to lock itVeriton M261 11. Install the front bezel13. Connect the HDD data cable and power-cable to the rear of HDD Front Bezel16. Connect the PA and PD power-cable to the MB connector 14. Connect the ODD data cable and power-cable to the rear of ODD15. Connect the P1 power-cable and FDD data cable to the MB connector Chapter19. Connect the AUDIO cables 20. Connect the front bezel LED cable 17. Connect the USB cables 18. Connect the Card Reader cableChapter 21. Install the TV&VGA&MODEM card 22. Close the system ChapterTroubleshooting ChapterChapter Mainboard Jumper Locations Jumper and Connector InformationChapter System Board Jumper Setting Jumper SettingsSetting Jumpers System Board Header SettingFront Audio Front Sys FAN 3pinCONN3FAN4P CPU FAN 4pinHFAN4MM1 Clear CMOSHEADER1X2 COM2 Chapter FRU Field Replaceable Unit List ChapterExploded Diagrams Aspire M1610Veriton M261 ChapterParts Lists The SPL will update later