Manuals / Aspire Digital / Computer Equipment / Computer Hardware

Aspire Digital M1610, M261 Connect the ODD data cable and power-cable to the rear of ODD, Chapter

Models: M261 M1610

1 80

Download 80 pages 33.8 Kb

Page 64

14.Connect the ODD data cable and power-cable to the rear of ODD.

14.Connect the ODD data cable and power-cable to the rear of ODD.

15.Connect the P1 power-cable and FDD data cable to the MB connector.

16.Connect the PA and PD power-cable to the MB connector.

56

Chapter 3

Image 64

Aspire Digital M1610, M261 manual Connect the ODD data cable and power-cable to the rear of ODD, Chapter

Contents

Aspire M1610/Veriton M261 Service GuidePRINTED IN TAIWAN Revision History Copyright DisclaimerSCREEN ConventionsMESSAGES Preface Page Table of Contents System SpecificationsEntering Setup Product Information Standard CMOS Features Advanced BIOS Features CPU Feature Hard Disk Boot PriorityMachine Disassembly and Replacement TroubleshootingJumper and Connector Information General Information Before You Begin Disassembly ProcedureSystem Specifications FeaturesChapter Operating SystemAudio BIOSIEEE 1394 Reserved I/O Connector Rear I/O ConnectorOnboard Connector Power SupplyMainboard Placement ChapterBlock Diagram ChapterAspire M1610 Front Panel The computer’s front panel consists of the followingAspire M1610 Rear Panel Veriton M261 Front Panel The computer’s front panel consists of the followingThe computer’s rear panel consists of the following Veriton M261 Rear PanelChapter Hardware Specifications and Configurations Processor SupportSystem Memory Interface System ClockSuper I/O - IT8718F SiS 968 MuTIOL 1G Media I/OAudio Sub-Systems - Realtek ALC888SCo-lay ALC888 LAN - Realtek8211BLdefault co-lay 8201CL phy Universal Serial BusTSB43AB23PDTG4 Host Controller Expansion SlotsPower & Power Management Hardware Monitor FunctionWake-Up Event From ACPI StateSPI Bus default System BIOSLPC Bus System Utilities ChapterEntering Setup Save & Exit Setup - Save CMOS value settings to CMOS and exit setup Exit Without Saving - Abandon all CMOS value changes and exit setupThe items in the main menu are explained below PC Health Status - This will display the current status of your PCProduct Information Standard CMOS Features Base Memory640K Extended MemoryParameter DescriptionOptions 1.44M, 3.5 - inchIDE Channel 0/1 Master IDE Channel 0/1 Slave The following screen shows the IDE Channel Slave menuSATA Channel 1/2 Master X Typematic Delay Msec Advanced BIOS FeaturesX Typematic Rate chars/sec NOTE Change these settings only if you are familiar with the chipset Setting to Off will allows users to use the arrowpassword prompt appears only when end users try to run Setup. System means that a passwordCPU Feature The following screen shows the CPU Features menuHard Disk Boot Priority Advanced Chipset Features The following screen shows the Advanced Chipset Features menuInternal Graphic Control X VGA Share Memory Size256 MB Graphic Engine ClockIntegrated Peripherals The following screen shows the Integrated Peripherals FeaturesOnboard IDE Device Onboard PCI Device The following screen shows the Onboard PCI Device menuX UR2 Duplex Mode Onboard Super IO DeviceHalf Power Management X Month AlarmX Day of Month Alarm X Time hh mm ss Alarmusing an ATX power supply. When ““instant off” is selected connect the AC power. Always off means the machine ismachine will always power on when connect the AC power ChapterPnP/PCI Configuration PCI Express relative itemsPC Health Status the extreme values spikes of the pulses creates Frequency/Voltage Controlpulses are reduced to flatter curves. If you do not Load Optimized Defaults Set Supervisor/User Password Save & Exit Setup Exit Without Saving Machine Disassembly and Replacement ChapterGeneral Information Before You BeginDisassembly Procedure Aspire M1610/Veriton M261 Disassembly4. Disconnect the front bezel LED cable 5. Disconnect the audio cables 6. Disconnect the USB cable7. Disconnect the Card Reader cable Chapter8. Disconnect the PA and PD power-cable from the MB connector 9. Disconnect P1 power cable and FDD data cable10. Disconnect the ODD power and data cables Chapter12. Disconnect the System Fan power-cable from the MB connector 11. Disconnect the HDD power and data cablesChapter Front Bezel Front BezelChapter Aspire M161018. Release the memory 17. Disconnect the CPU Cooler power-cable from the MB connectorChapter Chapter Reassembly Procedure Aspire M1610/Veriton M261 Reassembly6. Fit the CPU cooler to the MB and fasten four screws shown 5. Install the MemoryChapter 7. Connect the CPU Cooler power-cable to the MB connector 8. Connect the System Fan power-cable to the MB connector9. Install the ODD into the chassis and slide the ODD rail to lock it 10. Install the FDD and slide the FDD rail to lock it11. Install the front bezel 13. Connect the HDD data cable and power-cable to the rear of HDDVeriton M261 Front Bezel14. Connect the ODD data cable and power-cable to the rear of ODD 15. Connect the P1 power-cable and FDD data cable to the MB connector16. Connect the PA and PD power-cable to the MB connector Chapter19. Connect the AUDIO cables 20. Connect the front bezel LED cable 17. Connect the USB cables 18. Connect the Card Reader cableChapter 21. Install the TV&VGA&MODEM card 22. Close the system ChapterTroubleshooting ChapterChapter Mainboard Jumper Locations Jumper and Connector InformationChapter Jumper Settings Setting JumpersSystem Board Jumper Setting System Board Header SettingFront Audio Front Sys FAN 3pinCPU FAN 4pin HFAN4MM1CONN3FAN4P Clear CMOSHEADER1X2 COM2 Chapter FRU Field Replaceable Unit List ChapterExploded Diagrams Aspire M1610Veriton M261 ChapterParts Lists The SPL will update later