Manuals / Aspire Digital / Computer Equipment / Computer Hardware

Aspire Digital manual Disassembly Procedure, Aspire M1610/Veriton M261 Disassembly

Models: M261 M1610

1 80

Page 53

Disassembly Procedure

This section tells you how to disassemble the system when you need to perform system service. Please also refer to the disassembly video, if available.

CAUTION: Before you proceed, make sure you have turned off the system and all peripherals connected to it.

Aspire M1610/Veriton M261 Disassembly

NOTE: The only physical difference between the two models is the front bezel as shown in the procedures.

1.Place the system unit on a flat, steady surface.

Aspire M1610

Veriton M261

2.Release the Lock-handle then slide the left side door out.

3.Disconnect the VGA&TV&MODEM card.

Chapter 3

Page 53

Image 53

Aspire Digital manual Disassembly Procedure, Aspire M1610/Veriton M261 Disassembly

Contents

PRINTED IN TAIWAN Service GuideAspire M1610/Veriton M261 Revision History Disclaimer CopyrightMESSAGES ConventionsSCREEN Preface Page System Specifications Table of ContentsEntering Setup Product Information Standard CMOS Features Advanced BIOS Features CPU Feature Hard Disk Boot PriorityTroubleshooting Machine Disassembly and ReplacementJumper and Connector Information General Information Before You Begin Disassembly ProcedureFeatures System SpecificationsChapter Operating SystemIEEE 1394 Reserved BIOSAudio Rear I/O Connector I/O ConnectorOnboard Connector Power SupplyChapter Mainboard PlacementChapter Block DiagramThe computer’s front panel consists of the following Aspire M1610 Front PanelAspire M1610 Rear Panel The computer’s front panel consists of the following Veriton M261 Front PanelChapter Veriton M261 Rear PanelThe computer’s rear panel consists of the following Processor Support Hardware Specifications and ConfigurationsSystem Memory Interface System ClockAudio Sub-Systems - Realtek ALC888SCo-lay ALC888 SiS 968 MuTIOL 1G Media I/OSuper I/O - IT8718F Universal Serial Bus LAN - Realtek8211BLdefault co-lay 8201CL phyTSB43AB23PDTG4 Host Controller Expansion SlotsHardware Monitor Function Power & Power ManagementWake-Up Event From ACPI StateLPC Bus System BIOSSPI Bus default Chapter System UtilitiesEntering Setup Exit Without Saving - Abandon all CMOS value changes and exit setup Save & Exit Setup - Save CMOS value settings to CMOS and exit setupThe items in the main menu are explained below PC Health Status - This will display the current status of your PCProduct Information Base Memory Standard CMOS Features640K Extended MemoryDescription ParameterOptions 1.44M, 3.5 - inchIDE Channel 0/1 Master The following screen shows the IDE Channel Slave menu IDE Channel 0/1 SlaveSATA Channel 1/2 Master X Typematic Rate chars/sec Advanced BIOS FeaturesX Typematic Delay Msec Setting to Off will allows users to use the arrow NOTE Change these settings only if you are familiar with the chipsetpassword prompt appears only when end users try to run Setup. System means that a passwordThe following screen shows the CPU Features menu CPU FeatureHard Disk Boot Priority The following screen shows the Advanced Chipset Features menu Advanced Chipset FeaturesX VGA Share Memory Size Internal Graphic Control256 MB Graphic Engine ClockThe following screen shows the Integrated Peripherals Features Integrated PeripheralsOnboard IDE Device The following screen shows the Onboard PCI Device menu Onboard PCI DeviceHalf Onboard Super IO DeviceX UR2 Duplex Mode X Month Alarm Power ManagementX Day of Month Alarm X Time hh mm ss Alarmconnect the AC power. Always off means the machine is using an ATX power supply. When ““instant off” is selectedmachine will always power on when connect the AC power ChapterPCI Express relative items PnP/PCI ConfigurationPC Health Status pulses are reduced to flatter curves. If you do not Frequency/Voltage Controlthe extreme values spikes of the pulses creates Load Optimized Defaults Set Supervisor/User Password Save & Exit Setup Exit Without Saving Chapter Machine Disassembly and ReplacementBefore You Begin General InformationAspire M1610/Veriton M261 Disassembly Disassembly Procedure5. Disconnect the audio cables 6. Disconnect the USB cable 4. Disconnect the front bezel LED cable7. Disconnect the Card Reader cable Chapter9. Disconnect P1 power cable and FDD data cable 8. Disconnect the PA and PD power-cable from the MB connector10. Disconnect the ODD power and data cables ChapterChapter 11. Disconnect the HDD power and data cables12. Disconnect the System Fan power-cable from the MB connector Front Bezel Front BezelChapter Aspire M1610Chapter 17. Disconnect the CPU Cooler power-cable from the MB connector18. Release the memory Chapter Aspire M1610/Veriton M261 Reassembly Reassembly ProcedureChapter 5. Install the Memory6. Fit the CPU cooler to the MB and fasten four screws shown 8. Connect the System Fan power-cable to the MB connector 7. Connect the CPU Cooler power-cable to the MB connector9. Install the ODD into the chassis and slide the ODD rail to lock it 10. Install the FDD and slide the FDD rail to lock it13. Connect the HDD data cable and power-cable to the rear of HDD 11. Install the front bezelVeriton M261 Front Bezel15. Connect the P1 power-cable and FDD data cable to the MB connector 14. Connect the ODD data cable and power-cable to the rear of ODD16. Connect the PA and PD power-cable to the MB connector ChapterChapter 17. Connect the USB cables 18. Connect the Card Reader cable19. Connect the AUDIO cables 20. Connect the front bezel LED cable Chapter 21. Install the TV&VGA&MODEM card 22. Close the systemChapter TroubleshootingChapter Chapter Jumper and Connector InformationMainboard Jumper Locations Setting Jumpers Jumper SettingsSystem Board Jumper Setting System Board Header SettingFront Audio Sys FAN 3pin FrontHFAN4MM1 CPU FAN 4pinCONN3FAN4P Clear CMOSHEADER1X2 COM2 Chapter Chapter FRU Field Replaceable Unit ListAspire M1610 Exploded DiagramsChapter Veriton M261The SPL will update later Parts Lists