Manuals / Aspire Digital / Computer Equipment / Computer Hardware

Aspire Digital M261, M1610 manual Troubleshooting, Chapter

Models: M261 M1610

1 80

Download 80 pages 33.8 Kb

Page 67

Troubleshooting

Chapter 4

Troubleshooting

Please refer to generic troubleshooting guide for troubleshooting information relating to following topics:

•Power-On Self-Test (POST)

•POST Check Points

•POST Error Messages List

•Error Symptoms List

Chapter 4

59

Image 67

Aspire Digital M261, M1610 manual Troubleshooting, Chapter

Contents

Aspire M1610/Veriton M261 Service GuidePRINTED IN TAIWAN Revision History Disclaimer CopyrightSCREEN ConventionsMESSAGES Preface Page Advanced BIOS Features CPU Feature Hard Disk Boot Priority Table of ContentsSystem Specifications Entering Setup Product Information Standard CMOS FeaturesGeneral Information Before You Begin Disassembly Procedure Machine Disassembly and ReplacementTroubleshooting Jumper and Connector InformationOperating System System SpecificationsFeatures ChapterAudio BIOSIEEE 1394 Reserved Power Supply I/O ConnectorRear I/O Connector Onboard ConnectorChapter Mainboard PlacementChapter Block DiagramThe computer’s front panel consists of the following Aspire M1610 Front PanelAspire M1610 Rear Panel The computer’s front panel consists of the following Veriton M261 Front PanelThe computer’s rear panel consists of the following Veriton M261 Rear PanelChapter System Clock Hardware Specifications and ConfigurationsProcessor Support System Memory InterfaceSuper I/O - IT8718F SiS 968 MuTIOL 1G Media I/OAudio Sub-Systems - Realtek ALC888SCo-lay ALC888 Expansion Slots LAN - Realtek8211BLdefault co-lay 8201CL phyUniversal Serial Bus TSB43AB23PDTG4 Host ControllerFrom ACPI State Power & Power ManagementHardware Monitor Function Wake-Up EventSPI Bus default System BIOSLPC Bus Chapter System UtilitiesEntering Setup PC Health Status - This will display the current status of your PC Save & Exit Setup - Save CMOS value settings to CMOS and exit setupExit Without Saving - Abandon all CMOS value changes and exit setup The items in the main menu are explained belowProduct Information Extended Memory Standard CMOS FeaturesBase Memory 640K1.44M, 3.5 - inch ParameterDescription OptionsIDE Channel 0/1 Master The following screen shows the IDE Channel Slave menu IDE Channel 0/1 SlaveSATA Channel 1/2 Master X Typematic Delay Msec Advanced BIOS FeaturesX Typematic Rate chars/sec try to run Setup. System means that a password NOTE Change these settings only if you are familiar with the chipsetSetting to Off will allows users to use the arrow password prompt appears only when end usersThe following screen shows the CPU Features menu CPU FeatureHard Disk Boot Priority The following screen shows the Advanced Chipset Features menu Advanced Chipset FeaturesGraphic Engine Clock Internal Graphic ControlX VGA Share Memory Size 256 MBThe following screen shows the Integrated Peripherals Features Integrated PeripheralsOnboard IDE Device The following screen shows the Onboard PCI Device menu Onboard PCI DeviceX UR2 Duplex Mode Onboard Super IO DeviceHalf X Time hh mm ss Alarm Power ManagementX Month Alarm X Day of Month AlarmChapter using an ATX power supply. When ““instant off” is selectedconnect the AC power. Always off means the machine is machine will always power on when connect the AC powerPCI Express relative items PnP/PCI ConfigurationPC Health Status the extreme values spikes of the pulses creates Frequency/Voltage Controlpulses are reduced to flatter curves. If you do not Load Optimized Defaults Set Supervisor/User Password Save & Exit Setup Exit Without Saving Chapter Machine Disassembly and ReplacementBefore You Begin General InformationAspire M1610/Veriton M261 Disassembly Disassembly ProcedureChapter 4. Disconnect the front bezel LED cable5. Disconnect the audio cables 6. Disconnect the USB cable 7. Disconnect the Card Reader cableChapter 8. Disconnect the PA and PD power-cable from the MB connector9. Disconnect P1 power cable and FDD data cable 10. Disconnect the ODD power and data cables12. Disconnect the System Fan power-cable from the MB connector 11. Disconnect the HDD power and data cablesChapter Aspire M1610 Front BezelFront Bezel Chapter18. Release the memory 17. Disconnect the CPU Cooler power-cable from the MB connectorChapter Chapter Aspire M1610/Veriton M261 Reassembly Reassembly Procedure6. Fit the CPU cooler to the MB and fasten four screws shown 5. Install the MemoryChapter 10. Install the FDD and slide the FDD rail to lock it 7. Connect the CPU Cooler power-cable to the MB connector8. Connect the System Fan power-cable to the MB connector 9. Install the ODD into the chassis and slide the ODD rail to lock itFront Bezel 11. Install the front bezel13. Connect the HDD data cable and power-cable to the rear of HDD Veriton M261Chapter 14. Connect the ODD data cable and power-cable to the rear of ODD15. Connect the P1 power-cable and FDD data cable to the MB connector 16. Connect the PA and PD power-cable to the MB connector19. Connect the AUDIO cables 20. Connect the front bezel LED cable 17. Connect the USB cables 18. Connect the Card Reader cableChapter Chapter 21. Install the TV&VGA&MODEM card 22. Close the systemChapter TroubleshootingChapter Mainboard Jumper Locations Jumper and Connector InformationChapter System Board Header Setting Jumper SettingsSetting Jumpers System Board Jumper SettingFront Audio Sys FAN 3pin FrontClear CMOS CPU FAN 4pinHFAN4MM1 CONN3FAN4PHEADER1X2 COM2 Chapter Chapter FRU Field Replaceable Unit ListAspire M1610 Exploded DiagramsChapter Veriton M261The SPL will update later Parts Lists