Manuals / Aspire Digital / Computer Equipment / Computer Hardware

Aspire Digital manual Front Bezel, Chapter, Aspire M1610, Veriton M261

Models: M261 M1610

1 80

Download 80 pages 33.8 Kb

Page 57

Aspire M1610

14.Release the three latches on the front bezel, then remove the front bezel.

Aspire M1610	Veriton M261
Front Bezel	Front Bezel

15.Disconnect the ODD by railing the ODD-holder as shown below. Remove the ODD from the chassis.

16.Release the CPU cooler from the MB by removing the four securing screws.

Chapter 3

49

Image 57

Aspire Digital manual Front Bezel, Chapter, Aspire M1610, Veriton M261

Contents

Service Guide Aspire M1610/Veriton M261PRINTED IN TAIWAN Revision History Disclaimer CopyrightConventions SCREENMESSAGES Preface Page System Specifications Table of ContentsEntering Setup Product Information Standard CMOS Features Advanced BIOS Features CPU Feature Hard Disk Boot PriorityTroubleshooting Machine Disassembly and ReplacementJumper and Connector Information General Information Before You Begin Disassembly ProcedureFeatures System SpecificationsChapter Operating SystemBIOS AudioIEEE 1394 Reserved Rear I/O Connector I/O ConnectorOnboard Connector Power SupplyChapter Mainboard PlacementChapter Block DiagramThe computer’s front panel consists of the following Aspire M1610 Front PanelAspire M1610 Rear Panel The computer’s front panel consists of the following Veriton M261 Front PanelVeriton M261 Rear Panel The computer’s rear panel consists of the followingChapter Processor Support Hardware Specifications and ConfigurationsSystem Memory Interface System ClockSiS 968 MuTIOL 1G Media I/O Super I/O - IT8718FAudio Sub-Systems - Realtek ALC888SCo-lay ALC888 Universal Serial Bus LAN - Realtek8211BLdefault co-lay 8201CL phyTSB43AB23PDTG4 Host Controller Expansion SlotsHardware Monitor Function Power & Power ManagementWake-Up Event From ACPI StateSystem BIOS SPI Bus defaultLPC Bus Chapter System UtilitiesEntering Setup Exit Without Saving - Abandon all CMOS value changes and exit setup Save & Exit Setup - Save CMOS value settings to CMOS and exit setupThe items in the main menu are explained below PC Health Status - This will display the current status of your PCProduct Information Base Memory Standard CMOS Features640K Extended MemoryDescription ParameterOptions 1.44M, 3.5 - inchIDE Channel 0/1 Master The following screen shows the IDE Channel Slave menu IDE Channel 0/1 SlaveSATA Channel 1/2 Master Advanced BIOS Features X Typematic Delay MsecX Typematic Rate chars/sec Setting to Off will allows users to use the arrow NOTE Change these settings only if you are familiar with the chipsetpassword prompt appears only when end users try to run Setup. System means that a passwordThe following screen shows the CPU Features menu CPU FeatureHard Disk Boot Priority The following screen shows the Advanced Chipset Features menu Advanced Chipset FeaturesX VGA Share Memory Size Internal Graphic Control256 MB Graphic Engine ClockThe following screen shows the Integrated Peripherals Features Integrated PeripheralsOnboard IDE Device The following screen shows the Onboard PCI Device menu Onboard PCI DeviceOnboard Super IO Device X UR2 Duplex ModeHalf X Month Alarm Power ManagementX Day of Month Alarm X Time hh mm ss Alarmconnect the AC power. Always off means the machine is using an ATX power supply. When ““instant off” is selectedmachine will always power on when connect the AC power ChapterPCI Express relative items PnP/PCI ConfigurationPC Health Status Frequency/Voltage Control the extreme values spikes of the pulses createspulses are reduced to flatter curves. If you do not Load Optimized Defaults Set Supervisor/User Password Save & Exit Setup Exit Without Saving Chapter Machine Disassembly and ReplacementBefore You Begin General InformationAspire M1610/Veriton M261 Disassembly Disassembly Procedure5. Disconnect the audio cables 6. Disconnect the USB cable 4. Disconnect the front bezel LED cable7. Disconnect the Card Reader cable Chapter9. Disconnect P1 power cable and FDD data cable 8. Disconnect the PA and PD power-cable from the MB connector10. Disconnect the ODD power and data cables Chapter11. Disconnect the HDD power and data cables 12. Disconnect the System Fan power-cable from the MB connectorChapter Front Bezel Front BezelChapter Aspire M161017. Disconnect the CPU Cooler power-cable from the MB connector 18. Release the memoryChapter Chapter Aspire M1610/Veriton M261 Reassembly Reassembly Procedure5. Install the Memory 6. Fit the CPU cooler to the MB and fasten four screws shownChapter 8. Connect the System Fan power-cable to the MB connector 7. Connect the CPU Cooler power-cable to the MB connector9. Install the ODD into the chassis and slide the ODD rail to lock it 10. Install the FDD and slide the FDD rail to lock it13. Connect the HDD data cable and power-cable to the rear of HDD 11. Install the front bezelVeriton M261 Front Bezel15. Connect the P1 power-cable and FDD data cable to the MB connector 14. Connect the ODD data cable and power-cable to the rear of ODD16. Connect the PA and PD power-cable to the MB connector Chapter17. Connect the USB cables 18. Connect the Card Reader cable 19. Connect the AUDIO cables 20. Connect the front bezel LED cableChapter Chapter 21. Install the TV&VGA&MODEM card 22. Close the systemChapter TroubleshootingChapter Jumper and Connector Information Mainboard Jumper LocationsChapter Setting Jumpers Jumper SettingsSystem Board Jumper Setting System Board Header SettingFront Audio Sys FAN 3pin FrontHFAN4MM1 CPU FAN 4pinCONN3FAN4P Clear CMOSHEADER1X2 COM2 Chapter Chapter FRU Field Replaceable Unit ListAspire M1610 Exploded DiagramsChapter Veriton M261The SPL will update later Parts Lists