Manuals / Aspire Digital / Computer Equipment / Computer Hardware

Aspire Digital M1610 IDE Channel 0/1 Slave, The following screen shows the IDE Channel Slave menu

Models: M261 M1610

1 80

Download 80 pages 33.8 Kb

Page 30

Image 30

IDE Channel 0/1 Slave

The following screen shows the IDE Channel Slave menu.

NOTE: IDE Channel 0 and Channel 1 Slave have the same options, the only difference is the menu title.

Phoenix - AwardBIOS CMOS Setup Utility

IDE Channel 0 Slave

IDE Auto Detection	[Press Enter]	Item Help
		Item Help
Extended IDE Drive	[Auto]	Menu Level XX
Access Mode	[Auto]
Capacity	320 MB
Cylinder	0
Head	0
Precomp	0
Landing Zone	0
Sector	0

KLIJ :Move Enter: Select +/-/PU/PD :Value	F10: Save and Exit ESC:Exit
F1: General Help F5: Previous Values	F7: Optimized Defaults

Chapter 2

Page 30

Image 30

Aspire Digital M1610, M261 manual IDE Channel 0/1 Slave, The following screen shows the IDE Channel Slave menu

Contents

Service Guide Aspire M1610/Veriton M261PRINTED IN TAIWAN Revision History Copyright DisclaimerConventions SCREENMESSAGES Preface Page Entering Setup Product Information Standard CMOS Features Table of ContentsSystem Specifications Advanced BIOS Features CPU Feature Hard Disk Boot PriorityJumper and Connector Information Machine Disassembly and ReplacementTroubleshooting General Information Before You Begin Disassembly ProcedureChapter System SpecificationsFeatures Operating SystemBIOS AudioIEEE 1394 Reserved Onboard Connector I/O ConnectorRear I/O Connector Power SupplyMainboard Placement ChapterBlock Diagram ChapterAspire M1610 Front Panel The computer’s front panel consists of the followingAspire M1610 Rear Panel Veriton M261 Front Panel The computer’s front panel consists of the followingVeriton M261 Rear Panel The computer’s rear panel consists of the followingChapter System Memory Interface Hardware Specifications and ConfigurationsProcessor Support System ClockSiS 968 MuTIOL 1G Media I/O Super I/O - IT8718FAudio Sub-Systems - Realtek ALC888SCo-lay ALC888 TSB43AB23PDTG4 Host Controller LAN - Realtek8211BLdefault co-lay 8201CL phyUniversal Serial Bus Expansion SlotsWake-Up Event Power & Power ManagementHardware Monitor Function From ACPI StateSystem BIOS SPI Bus defaultLPC Bus System Utilities ChapterEntering Setup The items in the main menu are explained below Save & Exit Setup - Save CMOS value settings to CMOS and exit setupExit Without Saving - Abandon all CMOS value changes and exit setup PC Health Status - This will display the current status of your PCProduct Information 640K Standard CMOS FeaturesBase Memory Extended MemoryOptions ParameterDescription 1.44M, 3.5 - inchIDE Channel 0/1 Master IDE Channel 0/1 Slave The following screen shows the IDE Channel Slave menuSATA Channel 1/2 Master Advanced BIOS Features X Typematic Delay MsecX Typematic Rate chars/sec password prompt appears only when end users NOTE Change these settings only if you are familiar with the chipsetSetting to Off will allows users to use the arrow try to run Setup. System means that a passwordCPU Feature The following screen shows the CPU Features menuHard Disk Boot Priority Advanced Chipset Features The following screen shows the Advanced Chipset Features menu256 MB Internal Graphic ControlX VGA Share Memory Size Graphic Engine ClockIntegrated Peripherals The following screen shows the Integrated Peripherals FeaturesOnboard IDE Device Onboard PCI Device The following screen shows the Onboard PCI Device menuOnboard Super IO Device X UR2 Duplex ModeHalf X Day of Month Alarm Power ManagementX Month Alarm X Time hh mm ss Alarmmachine will always power on when connect the AC power using an ATX power supply. When ““instant off” is selectedconnect the AC power. Always off means the machine is ChapterPnP/PCI Configuration PCI Express relative itemsPC Health Status Frequency/Voltage Control the extreme values spikes of the pulses createspulses are reduced to flatter curves. If you do not Load Optimized Defaults Set Supervisor/User Password Save & Exit Setup Exit Without Saving Machine Disassembly and Replacement ChapterGeneral Information Before You BeginDisassembly Procedure Aspire M1610/Veriton M261 Disassembly7. Disconnect the Card Reader cable 4. Disconnect the front bezel LED cable5. Disconnect the audio cables 6. Disconnect the USB cable Chapter10. Disconnect the ODD power and data cables 8. Disconnect the PA and PD power-cable from the MB connector9. Disconnect P1 power cable and FDD data cable Chapter11. Disconnect the HDD power and data cables 12. Disconnect the System Fan power-cable from the MB connectorChapter Chapter Front BezelFront Bezel Aspire M161017. Disconnect the CPU Cooler power-cable from the MB connector 18. Release the memoryChapter Chapter Reassembly Procedure Aspire M1610/Veriton M261 Reassembly5. Install the Memory 6. Fit the CPU cooler to the MB and fasten four screws shownChapter 9. Install the ODD into the chassis and slide the ODD rail to lock it 7. Connect the CPU Cooler power-cable to the MB connector8. Connect the System Fan power-cable to the MB connector 10. Install the FDD and slide the FDD rail to lock itVeriton M261 11. Install the front bezel13. Connect the HDD data cable and power-cable to the rear of HDD Front Bezel16. Connect the PA and PD power-cable to the MB connector 14. Connect the ODD data cable and power-cable to the rear of ODD15. Connect the P1 power-cable and FDD data cable to the MB connector Chapter17. Connect the USB cables 18. Connect the Card Reader cable 19. Connect the AUDIO cables 20. Connect the front bezel LED cableChapter 21. Install the TV&VGA&MODEM card 22. Close the system ChapterTroubleshooting ChapterChapter Jumper and Connector Information Mainboard Jumper LocationsChapter System Board Jumper Setting Jumper SettingsSetting Jumpers System Board Header SettingFront Audio Front Sys FAN 3pinCONN3FAN4P CPU FAN 4pinHFAN4MM1 Clear CMOSHEADER1X2 COM2 Chapter FRU Field Replaceable Unit List ChapterExploded Diagrams Aspire M1610Veriton M261 ChapterParts Lists The SPL will update later