Maximum Height = 1.272 3.228 cm | ATTO Technology 2100R guide

ATTO Technology, Inc.

ATTO FibreBridge Installation & Operation Manual

Maximum Height

= 1.272” (3.228 cm)

Figure C-2 ATTO FibreBridge 2200R/D and 3200R Product Modules’ Board Layout

ATTO Technology, Inc.

- 49 -

Image 54

ATTO Technology 2100R, 2200R/D, 3200R manual Maximum Height = 1.272 3.228 cm

Contents

Atto Technology, Inc Atto FibreBridge Atto Technology, Inc Atto Fibrebridge Benefits and Features Updating the Firmware Within the Fibrebridge Atto Technology, Inc Introduction FibreBridge Product Module DescriptionFC Rack System Product Description Fibre Channel Technology References Atto FibreBridge Benefits and Features Fibre Channel Switch SupportAtto FibreChain Feature FibreBridge Feature Comparison Atto FC Rack Enclosure and Power Modules Physical DimensionsMounting Environmental Cooling AirflowCooling Fans Internal Power Distribution Power Module LED Indicator IEC Power Receptacle and SwitchInstallation and Removal Atto FC Rack System Installation Considerations Power Requirements Atto FibreBridge Product Module Integration Atto FibreBridge Power Connector Fibre Channel Ports Scsi Ports LED Indicators FibreChain Ports 2100 model onlyAtto FibreChain Port LEDs 2100R model only Ethernet Port Serial Port FibreBridge 2200R/D FibreBridge2200R/D Front View 2200R/D Side view with hole dimensions Power Supply Cooling and Airflow Fibre Channel Port Scsi LED Indicators on FibreBridge 2200R/D Quick Installation Instructions Cabling a FibreBridgeScsi Cabling Typical Scsi Cables Scsi Termination Fibre Channel Cabling ConnectorConnector Laser Type Cable Length Gbic Installation Instructions Gbic Module and Gbic Guide System Gbic Removal Instructions Media Interface Adapters MIAPin # Name MIA DB9 Connector MIA Installation Accessing the Atto FibreBridge over the RS-232 interface FibreBridge ServicesAtto BridgeTools Graphical Interface Configuration Program Monitoring and Managing the Atto FibreBridge Accessing the Atto FibreBridge over the Ethernet Port Setting up the IP Address using the RS-232 port Accessing through FTP Atto Technology, Inc Serverless Backup Support What is Serverless Backup? Target Descriptors General Operation of Serverless BackupEnabling Serverless Backup on the FibreBridge Segment Descriptors Updating the Firmware Within the FibreBridge Flashing the FibreBridge Addressing Scsi Devices Identifying the FibreBridge Identifying the Scsi Devices Connected to the FibreBridge Default Address Translation Appendix a Fibre Channel to Scsi Address Mapping Addressing Devices Connected to the FibreBridge Fibre Channel World Wide Name WWN Fibre Channel AddressingScsi Address Components Arbitrated Loop Port Address Alpa Scsi Architecture Model SAM-2 Logical Unit Addressing Bit Bit Number Address Address Method Specific Definition Peripheral Device Addressing Method FibreBridge Default Mode Virtual Device Addressing MethodLogical Unit Addressing Method Fibre Channel to Scsi Address Mapping SCSI-3 Command Changes for Hierarchical Addressing SupportSCSI-3 Inquiry Command Address Descriptors Setting the ID of the FibreBridge What to Expect When Setting Device IDsSCSI-3 Report LUNs Command Addressing Connected Scsi Devices Atto Technology, Inc Configuration for Consecutive IDs Scsi Device ID Translated LUN as it appears to the Host Atto Technology, Inc Canadian Standards Appendix B Radio and Television InterferenceFCC Standards European Standards Further results of FCC Testing Maximum Height = 1.582 4.015 cm Maximum Height = 1.272 3.228 cm Figure C-3 Atto FibreBridge 3200R Connector Layout Appendix D Fibre Channel Resources MIAs Appendix E Fibre Channel AccessoriesField Replacement Units FRU Cables/Copper Cables/Optical Cables/FibreChainCables/SCSI Appendix F How to Contact Atto Technology, Inc