$,6 9HUVLRQ | Axis Communications 700 manual

14	gywPuXu	AXIS 700 User’s Manual

PThe busy indicator turns on when the AXIS 700 is allocated for use and remains on during the scanning process.

by	The network indicator indicates network activity.
dy	The power indicator indicates that power is connected to the AXIS
	700.
va	ο While the AXIS 700 is idle, the Power indicator should be on, the
	Network indicator should flash randomly, and the Status and
	Busy indicators should be off.
R du	The AXIS 700 message display consists of 2 lines of 16 characters
	indicating status and menu options.

		$;,6
		9HUVLRQ;;;

gwu The Scan key digitize the material in the scanning device. For magazines and books, use this key to digitize each page.

gy The Send key sends the digitized material to the selected destination and releases the AXIS 700 for other users. For a single page/stack of paper, use this key to digitize the material and send the image in one step.

Image 15

Axis Communications 700 user manual $,6 9HUVLRQ

Contents

E rs M a n u a l v 1 OlXg D77 User’s Manual User’s Manual Copyright Axis Communications AB, 1997 Axis 700 User’s Manual Revision OlXg D77 User’s Manual Preface Dwy OlXg D77 User’s Manual Table of Contents Huv Zny SII t y OlXg D77 User’s Manual Introduction Kyv gy GywXxXxy Xyyy Axis 700 over the network using FTP Than the other way aroundAuy GywXx Guxux xyy OlXg D77 User’s Manual Basic Installation GywPuXu Duy Puw duy $,6 9HUVLRQ Ruwy Cancel keyAy The Menu key scrolls the menu Enter key Up and Down keys scroll and select menu options Turn off the Axis 700 by unplugging the power supply Scanning device documentation on how to do thisAlways consult the Network Administrator before making Changes to the network configuration Where x.xx is the software version number Power up the Axis 700. Press MenuAfter a few seconds this display will be shown Press Enter to edit the default router address Press Enter to edit the IP addressPress Enter to edit the subnet mask From the Axis 700 control panel Press Menu once more to display the final instructionsJyy Byy SWRd CyyzSux Xd Oxx Au bu IWRd Host will return ‘Reply from 172.19.2.254...’ or a similar Communication is establishedYour Axis 700. Type arp -a to display the ARP table IbXl u cg69 IP address and verify the communicationEther for Ethernet networks, e.g. arp -s ether spserv Ethernet address Host name Required by your system Typically performed using the command bootpd -aIcchd Where Http//172.19.2.254 GywPuXu Network protocol settings OlXg D77 User’s Manual Configuring the Axis This brings you to the Axis 700 Home GywRlXg D77 OlXg D77 User’s Manual Configuring the Axis Click Network Settings Sy jy Auhd0Tyu Oxxy GywRlXg D77 OlXg D77 User’s Manual Configuring the Axis From this page you can set the following parameters T4hd0 Tu Oxxy =countrycode Mandatory for all destination types. For FTP destinations, Configuration parameters are described in The ParameterLast five fields only apply to file destinations. Description, Transfer method and Destination fields are Can make these temporary destinations permanent by clicking Table. Click Detailed to view the detailed settingsDestination Name is the text that will appear Destination list on the Axis 700 control panel Mail addresses using the Smtp protocol T4uyMail destinations GywRlXg D77 When the URL is sent to an e-mail destination If z TuWill be stored Click Destination Defaults to change the default values SyyzuInformation Filenamesequencenumber.fileextension, e.g. image001.tif GywRlXg D77 Iy c Click New Profile to add a new profile to the list Most needs. This table lists the predefined profilesProfile Name list to edit an existing profile Axis 700 interface OlXg D77 User’s Manual Configuring the Axis GywRlXg D77 OlXg D77 User’s Manual Configuring the Axis GywRlXg D77 OlXg D77 User’s Manual Using the Axis T4u Gywi Xg D77 Gwu if Kyv P Perform these instructions from the Axis 700 control panel Axis 700 display shows Send to xxxxxx when it isOptionally, press Menu To change the default settings for Destinations on Several separate pages or stacks of papers Setting Sharp AR-series Yv gyu gyyCanon DR-3020 scanner. a job separation sheet inserted in a Other separation pages will be ignored Line Enter the name or IP address of your Axis 700 on Administrator might not allow users to add temporaryDown or re-started Interface OlXg D77 User’s Manual Using the Axis Black/white scanning devices, unless they can do gray-scale This table outlines when to use the predefined profilesDefault profile is Text Depending on your scanning device, some profiles may not be Syx Maintained by the AdministratorDefault paper size is Letter Du g Example Several separate pages Xux CRf uwOwuyuxy OlXg D77 User’s Manual Using the Axis Owy FTP Axis 700 User’s Manual Appendix a Troubleshooting OG h Axis 700 User’s Manual Tml Gu Xxu By Xxwu czz This table lists a summary of error conditions CDB Flatbed only Work. Attached scanner id is displayed in the event log Axis 700 Home Page is displayed. Click Administration Field and press EnterEvent log is displayed System looks like Ldap allows resources and services to be selected with easeAccessed with location-independence Axis 700 User’s Manual Appendix B Ldap Axis 700 User’s Manual Dwwu Only want to retrieve entries of the people class, with Could be achieved with the following filterObjectclass=personcn=john Axis 700 User’s Manual Appendix B Ldap Axis 700 User’s Manual OlXg D77 User’s Manual Appendix C The Parameter List Gives a brief description of the parameterAs in the table below ORG h DefaultRouter URL Smtp = Destination name END OlXg D77 User’s Manual Appendix D Updating the Software Compare against the latest software issues from AxisWhere you can download the latest versions of the software Axis web site on how to join the AxisNews OSG i y OlXg D77 User’s Manual Appendix D Updating the Software OSG i y Netscape Navigator 3.0 or higher Client Web browser, and at least one of these protocolsFile Transfer Protocol FTP server Simple Mail Transfer Protocol Smtp server Ouu 12V DC 13,2VA, via external power unit Axis PS-E Number is limited by the Eeprom memory. If using Ldap orSoftware over the network using FTP 12V DC 36VA, via external power unit Axis PS-C or Ouu OlXg D77 User’s Manual Appendix F Glossary Axis 700 User’s Manual OlXg D77 User’s Manual Appendix F Glossary 100 OlXg D77 User’s Manual Index 101 Http Dhcp Rarp OlXg D77 User’s Manual Index 103