OG h Axis 700 User’s Manual | Axis Communications instruction

70	OG h	AXIS 700 User’s Manual

fy

Follow these steps to restore the default settings using the Reset

button:

1.

Turn off the AXIS 700.

2.

Press and hold the Reset button while you switch on the AXIS 700.

Keep the Reset button pressed until the Status, Busy and Network

indicators flash at regular two second intervals.

fy

3.Release the Reset button and wait at least two seconds (one flash of the indicators).

4.Press and hold the Reset button for at least five seconds until the Network indicator remains constantly lit.

5.The AXIS 700 is now reset to factory default settings.

6.Restart the AXIS 700 by turning it off and then back on again.

kyv P	Follow these steps to reset to the defaults settings from a Web browser:
	1.	Start the Web browser.
	2.	Enter the name or the IP address of the AXIS 700 in the
		location/address field. The AXIS 700 Home Page is displayed.
	3.	Click Administration.
	4.	Click This AXIS 700.
	5.	Click Factory Defaults.
	The AXIS 700 will now restart with the factory default settings.

Image 71

Axis Communications user manual OG h Axis 700 User’s Manual

Contents

E rs M a n u a l v 1 OlXg D77 User’s Manual User’s Manual Copyright Axis Communications AB, 1997 Axis 700 User’s Manual Revision OlXg D77 User’s Manual Preface Dwy OlXg D77 User’s Manual Table of Contents Huv Zny SII t y OlXg D77 User’s Manual Introduction Kyv gy GywXxXxy Xyyy Auy Axis 700 over the network using FTPThan the other way around GywXx Guxux xyy OlXg D77 User’s Manual Basic Installation GywPuXu Duy Puw duy $,6 9HUVLRQ Ruwy Cancel keyAy The Menu key scrolls the menu Enter key Up and Down keys scroll and select menu options Turn off the Axis 700 by unplugging the power supply Scanning device documentation on how to do thisAlways consult the Network Administrator before making Changes to the network configuration After a few seconds this display will be shown Where x.xx is the software version numberPower up the Axis 700. Press Menu Press Enter to edit the subnet mask Press Enter to edit the default router addressPress Enter to edit the IP address From the Axis 700 control panel Press Menu once more to display the final instructionsJyy Byy SWRd CyyzSux Xd Oxx Au bu IWRd Your Axis 700. Type arp -a to display the ARP table Host will return ‘Reply from 172.19.2.254...’ or a similarCommunication is established Ether for Ethernet networks, e.g. arp -s ether spserv IbXl u cg69IP address and verify the communication Ethernet address Host name Required by your system Typically performed using the command bootpd -aIcchd Where Http//172.19.2.254 GywPuXu Network protocol settings OlXg D77 User’s Manual Configuring the Axis This brings you to the Axis 700 Home GywRlXg D77 OlXg D77 User’s Manual Configuring the Axis Click Network Settings Sy jy Auhd0Tyu Oxxy GywRlXg D77 OlXg D77 User’s Manual Configuring the Axis From this page you can set the following parameters T4hd0 Tu Oxxy =countrycode Mandatory for all destination types. For FTP destinations, Configuration parameters are described in The ParameterLast five fields only apply to file destinations. Description, Transfer method and Destination fields are Can make these temporary destinations permanent by clicking Table. Click Detailed to view the detailed settingsDestination Name is the text that will appear Destination list on the Axis 700 control panel Mail destinations Mail addresses using the Smtp protocolT4uy GywRlXg D77 Will be stored When the URL is sent to an e-mail destinationIf z Tu Information Click Destination Defaults to change the default valuesSyyzu Filenamesequencenumber.fileextension, e.g. image001.tif GywRlXg D77 Iy c Click New Profile to add a new profile to the list Most needs. This table lists the predefined profilesProfile Name list to edit an existing profile Axis 700 interface OlXg D77 User’s Manual Configuring the Axis GywRlXg D77 OlXg D77 User’s Manual Configuring the Axis GywRlXg D77 OlXg D77 User’s Manual Using the Axis T4u Gywi Xg D77 Gwu if Kyv P Perform these instructions from the Axis 700 control panel Axis 700 display shows Send to xxxxxx when it isOptionally, press Menu To change the default settings for Destinations on Several separate pages or stacks of papers Setting Sharp AR-series Yv gyu gyyCanon DR-3020 scanner. a job separation sheet inserted in a Other separation pages will be ignored Line Enter the name or IP address of your Axis 700 on Administrator might not allow users to add temporaryDown or re-started Interface OlXg D77 User’s Manual Using the Axis Black/white scanning devices, unless they can do gray-scale This table outlines when to use the predefined profilesDefault profile is Text Depending on your scanning device, some profiles may not be Syx Maintained by the AdministratorDefault paper size is Letter Du g Example Several separate pages Owuyuxy XuxCRf uw OlXg D77 User’s Manual Using the Axis Owy FTP Axis 700 User’s Manual Appendix a Troubleshooting OG h Axis 700 User’s Manual Tml Gu Xxu By Xxwu czz This table lists a summary of error conditions CDB Flatbed only Work. Attached scanner id is displayed in the event log Event log is displayed Axis 700 Home Page is displayed. Click AdministrationField and press Enter System looks like Ldap allows resources and services to be selected with easeAccessed with location-independence Axis 700 User’s Manual Appendix B Ldap Axis 700 User’s Manual Dwwu Objectclass=personcn=john Only want to retrieve entries of the people class, withCould be achieved with the following filter Axis 700 User’s Manual Appendix B Ldap Axis 700 User’s Manual As in the table below OlXg D77 User’s Manual Appendix C The Parameter ListGives a brief description of the parameter ORG h DefaultRouter URL Smtp = Destination name END OlXg D77 User’s Manual Appendix D Updating the Software Compare against the latest software issues from AxisWhere you can download the latest versions of the software Axis web site on how to join the AxisNews OSG i y OlXg D77 User’s Manual Appendix D Updating the Software OSG i y Netscape Navigator 3.0 or higher Client Web browser, and at least one of these protocolsFile Transfer Protocol FTP server Simple Mail Transfer Protocol Smtp server Ouu 12V DC 13,2VA, via external power unit Axis PS-E Number is limited by the Eeprom memory. If using Ldap orSoftware over the network using FTP 12V DC 36VA, via external power unit Axis PS-C or Ouu OlXg D77 User’s Manual Appendix F Glossary Axis 700 User’s Manual OlXg D77 User’s Manual Appendix F Glossary 100 OlXg D77 User’s Manual Index 101 Http Dhcp Rarp OlXg D77 User’s Manual Index 103