Field and press Enter | Axis Communications 700 specification

76	OG h	AXIS 700 User’s Manual

h

The AXIS 700 log file automatically logs all events and errors that have occurred since the last restart. You can access the log file using one of these methods:

•Control panel

•Web browser

R du	Follow these steps to display the log file from the control panel:
	1.	Press Menu		a few times, until you reach the Advanced
		menu.
	2.			to find the Server log option.
		Use
	3.	Press Enter		to enter the submenu.
	4.
		Use		to scroll through the messages.
kyv P	Follow these steps to display the log file from a Web browser:
	1.	Start the Web browser.
	2.	Enter the name or IP address of the AXIS 700 in the location/address

field and press Enter:

Example

http://172.19.2.254

3.The AXIS 700 Home Page is displayed. Click Administration.

4.Click Event Log.

The event log is displayed.

Image 77

Axis Communications user manual Field and press Enter, Axis 700 Home Page is displayed. Click Administration

Contents

E rs M a n u a l v 1 OlXg D77 User’s Manual User’s Manual Copyright Axis Communications AB, 1997 Axis 700 User’s Manual Revision OlXg D77 User’s Manual Preface Dwy OlXg D77 User’s Manual Table of Contents Huv Zny SII t y OlXg D77 User’s Manual Introduction Xxy GywXxXyyy Kyv gy Auy Axis 700 over the network using FTPThan the other way around GywXx Guxux xyy OlXg D77 User’s Manual Basic Installation GywPuXu Duy Puw duy $,6 9HUVLRQ Ay The Menu key scrolls the menu Enter key Cancel keyUp and Down keys scroll and select menu options Ruwy Always consult the Network Administrator before making Scanning device documentation on how to do thisChanges to the network configuration Turn off the Axis 700 by unplugging the power supply After a few seconds this display will be shown Where x.xx is the software version numberPower up the Axis 700. Press Menu Press Enter to edit the subnet mask Press Enter to edit the default router addressPress Enter to edit the IP address Jyy Press Menu once more to display the final instructionsByy From the Axis 700 control panel Sux CyyzXd Oxx SWRd Au bu IWRd Your Axis 700. Type arp -a to display the ARP table Host will return ‘Reply from 172.19.2.254...’ or a similarCommunication is established Ether for Ethernet networks, e.g. arp -s ether spserv IbXl u cg69IP address and verify the communication Ethernet address Host name Icchd Typically performed using the command bootpd -aWhere Required by your system Http//172.19.2.254 GywPuXu Network protocol settings OlXg D77 User’s Manual Configuring the Axis This brings you to the Axis 700 Home GywRlXg D77 OlXg D77 User’s Manual Configuring the Axis Click Network Settings Tyu Auhd0Oxxy Sy jy GywRlXg D77 OlXg D77 User’s Manual Configuring the Axis From this page you can set the following parameters T4hd0 Tu Oxxy =countrycode Last five fields only apply to file destinations. Configuration parameters are described in The ParameterDescription, Transfer method and Destination fields are Mandatory for all destination types. For FTP destinations, Destination Name is the text that will appear Table. Click Detailed to view the detailed settingsDestination list on the Axis 700 control panel Can make these temporary destinations permanent by clicking Mail destinations Mail addresses using the Smtp protocolT4uy GywRlXg D77 Will be stored When the URL is sent to an e-mail destinationIf z Tu Information Click Destination Defaults to change the default valuesSyyzu Filenamesequencenumber.fileextension, e.g. image001.tif GywRlXg D77 Iy c Profile Name list to edit an existing profile Most needs. This table lists the predefined profilesAxis 700 interface Click New Profile to add a new profile to the list OlXg D77 User’s Manual Configuring the Axis GywRlXg D77 OlXg D77 User’s Manual Configuring the Axis GywRlXg D77 OlXg D77 User’s Manual Using the Axis T4u Gywi Xg D77 Gwu if Kyv P Optionally, press Menu To change the default settings for Axis 700 display shows Send to xxxxxx when it isDestinations on Perform these instructions from the Axis 700 control panel Several separate pages or stacks of papers Setting Canon DR-3020 scanner. a job separation sheet inserted in a Yv gyu gyyOther separation pages will be ignored Sharp AR-series Line Down or re-started Administrator might not allow users to add temporaryInterface Enter the name or IP address of your Axis 700 on OlXg D77 User’s Manual Using the Axis Default profile is Text This table outlines when to use the predefined profilesDepending on your scanning device, some profiles may not be Black/white scanning devices, unless they can do gray-scale Default paper size is Letter Maintained by the AdministratorDu g Syx Example Several separate pages Owuyuxy XuxCRf uw OlXg D77 User’s Manual Using the Axis Owy FTP Axis 700 User’s Manual Appendix a Troubleshooting OG h Axis 700 User’s Manual Tml Gu Xxu By Xxwu czz This table lists a summary of error conditions CDB Flatbed only Work. Attached scanner id is displayed in the event log Event log is displayed Axis 700 Home Page is displayed. Click AdministrationField and press Enter Accessed with location-independence Ldap allows resources and services to be selected with easeAxis 700 User’s Manual Appendix B Ldap System looks like Axis 700 User’s Manual Dwwu Objectclass=personcn=john Only want to retrieve entries of the people class, withCould be achieved with the following filter Axis 700 User’s Manual Appendix B Ldap Axis 700 User’s Manual As in the table below OlXg D77 User’s Manual Appendix C The Parameter ListGives a brief description of the parameter ORG h DefaultRouter URL Smtp = Destination name END Where you can download the latest versions of the software Compare against the latest software issues from AxisAxis web site on how to join the AxisNews OlXg D77 User’s Manual Appendix D Updating the Software OSG i y OlXg D77 User’s Manual Appendix D Updating the Software OSG i y File Transfer Protocol FTP server Client Web browser, and at least one of these protocolsSimple Mail Transfer Protocol Smtp server Netscape Navigator 3.0 or higher Ouu Software over the network using FTP Number is limited by the Eeprom memory. If using Ldap or12V DC 36VA, via external power unit Axis PS-C or 12V DC 13,2VA, via external power unit Axis PS-E Ouu OlXg D77 User’s Manual Appendix F Glossary Axis 700 User’s Manual OlXg D77 User’s Manual Appendix F Glossary 100 OlXg D77 User’s Manual Index 101 Http Dhcp Rarp OlXg D77 User’s Manual Index 103