Press Enter to edit the IP address | Axis Communications 700

18	gywPuXu	AXIS 700 User’s Manual

4.Press Enter to edit the IP address:

(GLW,3DGGUHVV

5.Press Menu to move through the digits and highlight each digit, one at a time.

6.Use to increase or decrease each highlighted digit, as required.

7.Press Enter to confirm the changes.

8.Press Menu to display the default router address:

'HIDXOWURXWHU

9.Press Enter to edit the default router address:

(GLWURXWHU

10.To change the value, repeat steps 5-7 above.

11.Press Menu to display the subnet mask:

1HWPDVN

12.Press Enter to edit the subnet mask:

(GLWQHWPDVN

13.To change the value, repeat steps 5-7 above.

14.Press Menu to display the node address. This address is not editable. The node address should equal the AXIS 700 serial number found on the underside label of the unit.

Image 19

Axis Communications 700 user manual Press Enter to edit the IP address, Press Enter to edit the default router address

Contents

E rs M a n u a l v 1 OlXg D77 User’s Manual User’s Manual Copyright Axis Communications AB, 1997 Axis 700 User’s Manual Revision OlXg D77 User’s Manual Preface Dwy OlXg D77 User’s Manual Table of Contents Huv Zny SII t y OlXg D77 User’s Manual Introduction Kyv gy GywXxXxy Xyyy Than the other way around Axis 700 over the network using FTPAuy GywXx Guxux xyy OlXg D77 User’s Manual Basic Installation GywPuXu Duy Puw duy $,6 9HUVLRQ Ruwy Cancel keyAy The Menu key scrolls the menu Enter key Up and Down keys scroll and select menu options Turn off the Axis 700 by unplugging the power supply Scanning device documentation on how to do thisAlways consult the Network Administrator before making Changes to the network configuration Power up the Axis 700. Press Menu Where x.xx is the software version numberAfter a few seconds this display will be shown Press Enter to edit the IP address Press Enter to edit the default router addressPress Enter to edit the subnet mask From the Axis 700 control panel Press Menu once more to display the final instructionsJyy Byy SWRd CyyzSux Xd Oxx Au bu IWRd Communication is established Host will return ‘Reply from 172.19.2.254...’ or a similarYour Axis 700. Type arp -a to display the ARP table IP address and verify the communication IbXl u cg69Ether for Ethernet networks, e.g. arp -s ether spserv Ethernet address Host name Required by your system Typically performed using the command bootpd -aIcchd Where Http//172.19.2.254 GywPuXu Network protocol settings OlXg D77 User’s Manual Configuring the Axis This brings you to the Axis 700 Home GywRlXg D77 OlXg D77 User’s Manual Configuring the Axis Click Network Settings Sy jy Auhd0Tyu Oxxy GywRlXg D77 OlXg D77 User’s Manual Configuring the Axis From this page you can set the following parameters T4hd0 Tu Oxxy =countrycode Mandatory for all destination types. For FTP destinations, Configuration parameters are described in The ParameterLast five fields only apply to file destinations. Description, Transfer method and Destination fields are Can make these temporary destinations permanent by clicking Table. Click Detailed to view the detailed settingsDestination Name is the text that will appear Destination list on the Axis 700 control panel T4uy Mail addresses using the Smtp protocolMail destinations GywRlXg D77 If z Tu When the URL is sent to an e-mail destinationWill be stored Syyzu Click Destination Defaults to change the default valuesInformation Filenamesequencenumber.fileextension, e.g. image001.tif GywRlXg D77 Iy c Click New Profile to add a new profile to the list Most needs. This table lists the predefined profilesProfile Name list to edit an existing profile Axis 700 interface OlXg D77 User’s Manual Configuring the Axis GywRlXg D77 OlXg D77 User’s Manual Configuring the Axis GywRlXg D77 OlXg D77 User’s Manual Using the Axis T4u Gywi Xg D77 Gwu if Kyv P Perform these instructions from the Axis 700 control panel Axis 700 display shows Send to xxxxxx when it isOptionally, press Menu To change the default settings for Destinations on Several separate pages or stacks of papers Setting Sharp AR-series Yv gyu gyyCanon DR-3020 scanner. a job separation sheet inserted in a Other separation pages will be ignored Line Enter the name or IP address of your Axis 700 on Administrator might not allow users to add temporaryDown or re-started Interface OlXg D77 User’s Manual Using the Axis Black/white scanning devices, unless they can do gray-scale This table outlines when to use the predefined profilesDefault profile is Text Depending on your scanning device, some profiles may not be Syx Maintained by the AdministratorDefault paper size is Letter Du g Example Several separate pages CRf uw XuxOwuyuxy OlXg D77 User’s Manual Using the Axis Owy FTP Axis 700 User’s Manual Appendix a Troubleshooting OG h Axis 700 User’s Manual Tml Gu Xxu By Xxwu czz This table lists a summary of error conditions CDB Flatbed only Work. Attached scanner id is displayed in the event log Field and press Enter Axis 700 Home Page is displayed. Click AdministrationEvent log is displayed System looks like Ldap allows resources and services to be selected with easeAccessed with location-independence Axis 700 User’s Manual Appendix B Ldap Axis 700 User’s Manual Dwwu Could be achieved with the following filter Only want to retrieve entries of the people class, withObjectclass=personcn=john Axis 700 User’s Manual Appendix B Ldap Axis 700 User’s Manual Gives a brief description of the parameter OlXg D77 User’s Manual Appendix C The Parameter ListAs in the table below ORG h DefaultRouter URL Smtp = Destination name END OlXg D77 User’s Manual Appendix D Updating the Software Compare against the latest software issues from AxisWhere you can download the latest versions of the software Axis web site on how to join the AxisNews OSG i y OlXg D77 User’s Manual Appendix D Updating the Software OSG i y Netscape Navigator 3.0 or higher Client Web browser, and at least one of these protocolsFile Transfer Protocol FTP server Simple Mail Transfer Protocol Smtp server Ouu 12V DC 13,2VA, via external power unit Axis PS-E Number is limited by the Eeprom memory. If using Ldap orSoftware over the network using FTP 12V DC 36VA, via external power unit Axis PS-C or Ouu OlXg D77 User’s Manual Appendix F Glossary Axis 700 User’s Manual OlXg D77 User’s Manual Appendix F Glossary 100 OlXg D77 User’s Manual Index 101 Http Dhcp Rarp OlXg D77 User’s Manual Index 103