Hardware Installation | B&B Electronics EIR608-xSFP specs

Hardware Installation

Installation Steps

1.Unpack the Industrial switch.

2.Ensure the DIN-Rail is tightly screwed to the Industrial switch. If not, refer to DIN-Rail Mounting section for DIN-Rail installation. To panel mount the Industrial switch, refer to Panel Mounting section.

3.Apply power to the switch (refer to the Wiring the Power Inputs section). The power LED will light.

4.Connect CAT 5 cables to the Industrial switch’s RJ-45 ports and to the network devices.

[NOTE] If the network devices do not support MID/MDIX, a crossover cable may be required.

Manual Documentation Number: EIR608-xSFP_0708m

15

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com

Image 23

B&B Electronics EIR608-xSFP manual Hardware Installation, Installation Steps

Contents

Product Description Eight Port Managed Industrial Ethernet Switches FCC Content Pin Assignment About Web-based Management Preparing for Web Management System Event Log Event Configuration Snmp Configuration Introduction Overview ¾ Gvrp Features Manual Documentation Number EIR608-xSFP0708m Packing List Front Panel Dimensions W x D x H Top View Wiring the Power Inputs LED Indicators Wiring the Fault Alarm Contact „ RJ-45 Pin Assignments Pin Number Pin MDI-X Signal Name MDI Signal NamePorts Cabling Transceiver Inserted LC connector to the transceiver Pull out from the SFP module DIN-Rail Mounting Mounting Installation Panel Mounting Installation Steps Hardware Installation Ring Application Dual Homing Application Coupling Ring Application Pin Assignment Connecting to the Console PortDB9 Connector RJ-45 Connector Login in the Console Interface CLI Management Modes Access Prompt Exit About This Mode1 Method Commands Level Commands Set List System Commands Set High IP PasswordUsername Low IP Port Commands Set 101001000auto PortidFull half Value Enable Disable Trunk Commands Set GroupID Vlan Commands Set PortNumber Group NamePortNumbers GroupName Seconds Spanning Tree Commands Set~61440 Stp-path-cost Spanning-treeHello-time seconds Forward-time seconds TrueFalse AutoTrueFalse Igmp Commands Set QOS Commands Set Mac / Filter Table Commands Set Snmp Commands Set Read View Name Write View Name Notify View NameNoAuthNoPrivAuthNoP RivAuthPriv ExactPrifix View Name SNMPV3 agent Port Mirroring Commands SetRemove specified Mibview table Words 802.1x Commands SetPort ID Number Disable reject acceptSec Authorize Tftp Commands SetSystemLog, Smtp and Event Commands Set SystemlogSMTPBoth ClientserverbothAccount Index Email address Start time End time Sntp Commands Set Timezone Ring Commands SetMinute Dual Homing Port 1st Ring Port 2nd RingCoupling Port Control Port Preparing for Web Management System LoginAbout Web-based Management Main interface System Information IP Configuration Dhcp Client Entries Dhcp Server System configuration Dhcp Server Port and IP Bindings Tftp Update Firmware Tftp Server IP Address Enter the Tftp server IP Tftp Restore ConfigurationTftp Backup Configuration System Event Log Syslog Configuration System Event Log Smtp Configuration System Event Log Event Configuration Fault Relay Alarm Local Time Zone Conversion from UTC Time at 1200 UTC Sntp Configuration Manual Documentation Number EIR608-xSFP0708m Daylight Saving Offset mins Enter the offset in minutes IP Security Port Statistics User Authentication Port Control Port Trunk Aggregator setting Remove Aggregator Information State Activity Port Mirroring Rate Limiting Vlan configuration Port-based Vlan Vlan configuration Vlan Port Based interface „ The Vlan is displayed Use 802.1Q Vlan „ Hybrid Link Both Access Link and Trunk Link 802.1Q Configuration Vlan group name and Vlan ID can be changed Click Apply Rapid Spanning Tree Rstp System Configuration Rstp Port Configuration Snmp Configuration „ Community Strings System Configuration Context Table Trap ConfigurationSNMPV3 Configuration User Profile „ Authentication Password Enter password Snmp V3 configuration interface MIBview Table Access TableGroup Table QoS Policy and Priority Type QoS Configuration Port Base Priority COS Configuration TOS Configuration Igmp Configuration Ring Manual Documentation Number EIR608-xSFP0708m Rstp cannot exist at the same time Security 802.1X/Radius Configuration 802.1x Port Configuration Misc Configuration „ Add the Static MAC Address MAC Address Table MAC Filtering All MAC Addresses Factory Default System Reboot Save Configuration Trouble shooting MAC address StandardProtocol Transfer Rate Consumption Install „ LC Single mode 9/125um Back-planePower Supply Power Relay Alarm SafetyStability testing