Port Mirroring | B&B Electronics EIR608-xSFP specs

Port Mirroring

Port mirroring is a method to monitor traffic in switched networks. Traffic flowing through the indicated ports can be monitored by a specified port.

Destination Port: Only one port can be selected as the destination (mirror) port for monitoring both RX and TX traffic from the source port. Two ports may be configured to monitor RX and TX traffic separately. A LAN analyzer can be connected to the mirror port.

Source Port: Select the ports to monitor. All monitored port traffic will be sent to the mirror (destination) port. Multiple source ports by can be selected by checking the RX or TX check boxes.

Click Apply

Port Trunk – Port Mirroring interface

Manual Documentation Number: EIR608-xSFP_0708m

65

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com

Image 73

B&B Electronics EIR608-xSFP manual Port Mirroring

Contents

Product Description Eight Port Managed Industrial Ethernet Switches FCC Content Pin Assignment About Web-based Management Preparing for Web Management System Event Log Event Configuration Snmp Configuration Introduction Overview ¾ Gvrp Features Manual Documentation Number EIR608-xSFP0708m Packing List Front Panel Dimensions W x D x H Top View Wiring the Power Inputs LED Indicators Wiring the Fault Alarm Contact Ports Pin MDI-X Signal Name MDI Signal Name„ RJ-45 Pin Assignments Pin Number Cabling Transceiver Inserted LC connector to the transceiver Pull out from the SFP module DIN-Rail Mounting Mounting Installation Panel Mounting Installation Steps Hardware Installation Ring Application Dual Homing Application Coupling Ring Application DB9 Connector RJ-45 Connector Connecting to the Console PortPin Assignment Login in the Console Interface CLI Management Modes Access Prompt Exit About This Mode1 Method Commands Level Commands Set List System Commands Set Username PasswordLow IP High IP Port Commands Set Full half Portid101001000auto Value Enable Disable Trunk Commands Set GroupID Vlan Commands Set PortNumbers Group NameGroupName PortNumber ~61440 Spanning Tree Commands SetSeconds Hello-time seconds Spanning-treeForward-time seconds Stp-path-cost TrueFalse AutoTrueFalse Igmp Commands Set QOS Commands Set Mac / Filter Table Commands Set Snmp Commands Set NoAuthNoPrivAuthNoP RivAuthPriv NameExactPrifix Read View Name Write View Name Notify View Remove specified Port Mirroring Commands SetMibview table View Name SNMPV3 agent Port ID 802.1x Commands SetWords Sec Disable reject acceptNumber SystemLog, Smtp and Event Commands Set Tftp Commands SetAuthorize Account ClientserverbothIndex Email address SystemlogSMTPBoth Start time End time Sntp Commands Set Minute Ring Commands SetTimezone Coupling Port 1st Ring Port 2nd RingControl Port Dual Homing Port About Web-based Management System LoginPreparing for Web Management Main interface System Information IP Configuration Dhcp Client Entries Dhcp Server System configuration Dhcp Server Port and IP Bindings Tftp Update Firmware Tftp Backup Configuration Tftp Restore ConfigurationTftp Server IP Address Enter the Tftp server IP System Event Log Syslog Configuration System Event Log Smtp Configuration System Event Log Event Configuration Fault Relay Alarm Local Time Zone Conversion from UTC Time at 1200 UTC Sntp Configuration Manual Documentation Number EIR608-xSFP0708m Daylight Saving Offset mins Enter the offset in minutes IP Security Port Statistics User Authentication Port Control Port Trunk Aggregator setting Remove Aggregator Information State Activity Port Mirroring Rate Limiting Vlan configuration Port-based Vlan Vlan configuration Vlan Port Based interface „ The Vlan is displayed Use 802.1Q Vlan „ Hybrid Link Both Access Link and Trunk Link 802.1Q Configuration Vlan group name and Vlan ID can be changed Click Apply Rapid Spanning Tree Rstp System Configuration Rstp Port Configuration Snmp Configuration „ Community Strings System Configuration SNMPV3 Configuration Trap ConfigurationContext Table User Profile „ Authentication Password Enter password Snmp V3 configuration interface Group Table Access TableMIBview Table QoS Policy and Priority Type QoS Configuration Port Base Priority COS Configuration TOS Configuration Igmp Configuration Ring Manual Documentation Number EIR608-xSFP0708m Rstp cannot exist at the same time Security 802.1X/Radius Configuration 802.1x Port Configuration Misc Configuration „ Add the Static MAC Address MAC Address Table MAC Filtering All MAC Addresses Factory Default System Reboot Save Configuration Trouble shooting Protocol StandardTransfer Rate MAC address Power Supply „ LC Single mode 9/125um Back-planePower Consumption Install Stability testing SafetyRelay Alarm