Fault Relay Alarm | B&B Electronics EIR608-xSFP specification

System event selection: Four selections available – Cold Start, Warm Start, SNMP Authentication Failure, and X-ring topology change. Mark the checkbox to select the event. When the selected events occur, the system will send the logs.

Event Configuration interface

Port event selection: When a port specific event occurs, the system will generate a log entry and email notification. Three selections are available – Link UP, Link Down, and Link UP & Link Down.

Fault Relay Alarm

Power Failure: When the check box is marked, the Fault LED will light

54	Manual Documentation Number: EIR608-xSFP_0708m
	Manual Documentation Number: EIR608-xSFP_0708m
	B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
	B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com

Image 62

B&B Electronics EIR608-xSFP manual Fault Relay Alarm

Contents

Product Description Eight Port Managed Industrial Ethernet Switches FCC Content Pin Assignment About Web-based Management Preparing for Web Management System Event Log Event Configuration Snmp Configuration Overview Introduction Features ¾ Gvrp Manual Documentation Number EIR608-xSFP0708m Packing List Dimensions W x D x H Front Panel Top View Wiring the Power Inputs Wiring the Fault Alarm Contact LED Indicators „ RJ-45 Pin Assignments Pin Number Pin MDI-X Signal Name MDI Signal NamePorts Cabling Transceiver Inserted LC connector to the transceiver Pull out from the SFP module Mounting Installation DIN-Rail Mounting Panel Mounting Hardware Installation Installation Steps Ring Application Coupling Ring Application Dual Homing Application Pin Assignment Connecting to the Console PortDB9 Connector RJ-45 Connector Login in the Console Interface CLI Management Commands Level Modes Access Prompt Exit About This Mode1 Method Commands Set List System Commands Set Low IP PasswordUsername High IP Port Commands Set 101001000auto PortidFull half Enable Disable Value Trunk Commands Set Vlan Commands Set GroupID GroupName Group NamePortNumbers PortNumber Seconds Spanning Tree Commands Set~61440 Forward-time seconds Spanning-treeHello-time seconds Stp-path-cost AutoTrueFalse TrueFalse QOS Commands Set Igmp Commands Set Mac / Filter Table Commands Set Snmp Commands Set ExactPrifix NameNoAuthNoPrivAuthNoP RivAuthPriv Read View Name Write View Name Notify View Mibview table Port Mirroring Commands SetRemove specified View Name SNMPV3 agent Words 802.1x Commands SetPort ID Number Disable reject acceptSec Authorize Tftp Commands SetSystemLog, Smtp and Event Commands Set Index Email address ClientserverbothAccount SystemlogSMTPBoth Sntp Commands Set Start time End time Timezone Ring Commands SetMinute Control Port 1st Ring Port 2nd RingCoupling Port Dual Homing Port Preparing for Web Management System LoginAbout Web-based Management Main interface IP Configuration System Information Dhcp Server System configuration Dhcp Client Entries Tftp Update Firmware Dhcp Server Port and IP Bindings Tftp Server IP Address Enter the Tftp server IP Tftp Restore ConfigurationTftp Backup Configuration System Event Log Syslog Configuration System Event Log Smtp Configuration System Event Log Event Configuration Fault Relay Alarm Sntp Configuration Local Time Zone Conversion from UTC Time at 1200 UTC Manual Documentation Number EIR608-xSFP0708m Daylight Saving Offset mins Enter the offset in minutes IP Security User Authentication Port Statistics Port Control Aggregator setting Port Trunk Remove Aggregator Information State Activity Port Mirroring Rate Limiting Vlan configuration Vlan configuration Port-based Vlan Vlan Port Based interface „ The Vlan is displayed Use 802.1Q Vlan 802.1Q Configuration „ Hybrid Link Both Access Link and Trunk Link Vlan group name and Vlan ID can be changed Click Apply Rstp System Configuration Rapid Spanning Tree Rstp Port Configuration Snmp Configuration System Configuration „ Community Strings Context Table Trap ConfigurationSNMPV3 Configuration „ Authentication Password Enter password User Profile Snmp V3 configuration interface MIBview Table Access TableGroup Table QoS Configuration QoS Policy and Priority Type COS Configuration Port Base Priority Igmp Configuration TOS Configuration Ring Manual Documentation Number EIR608-xSFP0708m Rstp cannot exist at the same time 802.1X/Radius Configuration Security 802.1x Port Configuration Misc Configuration MAC Address Table „ Add the Static MAC Address MAC Filtering Factory Default All MAC Addresses Save Configuration System Reboot Trouble shooting Transfer Rate StandardProtocol MAC address Power „ LC Single mode 9/125um Back-planePower Supply Consumption Install Relay Alarm SafetyStability testing