Replacement Parts Continued
Description |
| Part No. |
|
|
|
| |
| GLC 80 | GLC 100 | GLC125 |
|
|
|
|
DECAL •BONDED NEUTRAL" | LB0300A00 | LB0300A00 | LB0300A00 |
DECAL •FUSE TYPE & WARNING" | LB0300A01 | LB0300A01 | LB0300A01 |
DECAL, CONTROL PANEL | LB0094B60 | LB0094B60 | LB0094B60 |
PLACARD, •REMOTE START" | LB0095A42 | LB0095A42 | LB0095A42 |
DECAL, BALDOR LOGO,26" | LB0100A27 | LB0100A27 | LB0100A27 |
DECAL, BALDOR LOGO | LB0100A29 | LB0100A29 | LB0100A29 |
DECAL, | LB0094A11 | LB0094A11 | LB0094A11 |
DECAL, WARNING, AUTO START | LB0094A30 | LB0094A30 | LB0094A30 |
PLACARD, •LINE" | LB0095A07 | LB0095A07 | LB0095A07 |
PLACARD, •LOAD" | LB0095A08 | LB0095A08 | LB0095A08 |
PLACARD, •NEUTRAL" | LB0095A15 | LB0095A15 | LB0095A15 |
PLACARD, •L1" | LB0095A16 | LB0095A16 | LB0095A16 |
PLACARD, •L2" | LB0095A17 | LB0095A17 | LB0095A17 |
PLACARD, •L3" |
| LB0095A18 | LB0095A18 |
PLACARD, •A.C. CONNECTION" | LB0095A51 | LB0095A51 | LB0095A51 |
PLACARD, •GROUND" | LB0095A37 | LB0095A37 | LB0095A37 |
Flywheel
Housing
Magnetic
Pickup
Figure A-1 Magnetic Pickup Replacement
This procedure is intended to help during the replacement of a Magnetic Pickup speed sensor.
1.Ensure that the battery is disconnected from the generator set prior to performing any service work on the unit. Remove the old Magnetic Pickup sensor.
2.Ensure that a tooth on the flywheel gear ring is centered directly in the hole for the Magnetic Pickup. If not, rotate the engine/generator to center a tooth by placing a socket on the engine main crank pulley.
d+
Cable 
Jam
Nut
dFlywheel Gear Ring
DO NOT insert a screwdriver into the hole for the magnetic pickup as the threads in the flywheel housing can be damaged. DO NOT use the generator cooling fan to rotate the engine/generator. The fan may crack and will have to be replaced.
3.With a tooth centered in the hole, measure the distance •d" from the top of the tooth to the outside top of the flywheel housing. Set the jam nut on the magnetic pickup slightly beyond that measurement •d+" to ensure that the magnetic pickup fully threads into the housing. (If the flywheel housing or magnetic pickup threads are damaged, the magnetic pickup may seem to have bottomed out when it stopped due to bad threads.)
4.Thread the magnetic pickup into the flywheel housing until it bottoms out on the flywheel tooth.
5.Back the magnetic pickup out 1/2 turn and tighten the jam nut to the flywheel housing.
Note: The 1/2 turn out is very important. Too little can ruin the magnetic pickup and create extra cleanup work. Too much can result in poor operation.
6.Verify proper operation. (1.3 VAC while cranking)
7.Apply a drop of wicking fastener adhesive to the locking nut of the magnetic pickup. (Loctite, Permabond, etc.)
MN2408 | Series GLC |
