Power control port
The Wizard IP Plus provides a serial port for connection to one or more optional power control units. This allows you to control the mains power being supplied to the connected host(s) so that an authorised remote user can, if necessary, perform a complete cold reboot on a failed host system.
The control connector of the first power switch is connected, via serial cable, to the rear panel of the Wizard IP Plus. Any additional power switches are then connected via a
control | BLACK BOX |
| Power |
connections |
|
| |
| LOC REM VNC 100 LNK PWR | switch | |
|
|
| |
|
|
| boxes |
Box 1 | IN | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
| OUT |
|
|
|
|
|
|
|
|
Box 2 | IN | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
| OUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Power to computer |
|
|
|
|
|
|
|
|
| Box 2, port 6 - address: 26 |
Box 3 | IN | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
| OUT |
|
|
|
|
|
|
|
|
Box 4 | IN | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
The power ports are connected to the power inputs of each computer and the power switch box(es) are then connected to a mains power supply.
IMPORTANT: Power switching devices have a maximum current rating. It is essential to ensure that the total current drawn by the equipment connected to the power switching device does not exceed the current rating of the power switching device. You must also ensure that the current drawn from any mains socket does not exceed the current rating of the mains socket.
Setting up, configuring and using power switching requires three main steps:
•Connect and address the switch boxes
•Configure the power strings
•Operate remote power switching
To connect and address the switch boxes
Note: The Wizard IP Plus can be powered on during this procedure, however, the switch boxes should be switched off.
1Mount up to four switch boxes in positions where they are close to the computers that they will control and not too distant from the Wizard IP Plus (preferably within 2.5 metres).
2Use a serial cable with an RJ9 and a
SOLE | VG | |
A | ||
|
DVI |
| PO |
|
|
|
| |
| VG | WER | CONT |
|
| ||
|
|
| |
|
|
| R |
|
|
| OL |
|
| K/ |
|
|
| SWITCH |
|
|
| M |
|
|
|
| V |
|
|
| M |
3For each of the remaining switch boxes (if used), use a serial cable with RJ9 connectors at both ends (see Appendix 7 for specification). Connect one end to the socket marked ‘OUT’ of the previous box and the other end to the socket marked ‘IN’ of the next box.
4Set the addressing switches on each switch
box using the two micro switches marked Box Switch 1 Switch 2
‘Slct’ on the front panel. The box connected | 1 | Off | Off | |
directly to the Wizard IP Plus is Box 1 and | 2 | On | Off | |
so on, down the | 3 | Off | On | |
the end. | ||||
4 | On | On | ||
5 Connect IEC to IEC power leads between | ||||
Off = switch upwards |
| |||
each port and the power input socket |
| |||
On = switch downwards |
| |||
of each computer that requires power | Switch 1 is on the left side |
| ||
switching. Carefully note to which power
ports, on which boxes, each computer is connected. If server systems have multiple power inputs, then each input must be connected via separate ports, which can be on the same, or different boxes.
6 Connect each box to a suitable mains power input.
Now proceed to the configuration stage covered in the Power switching configuration section within the Configuration chapter.
®
14
