Additional Safety Rules

e. NEVER place your face or body in line with the cutting tool.

•NEVER place your fingers and hands in the path of the sawblade or other cutting tool.

•NEVER reach in back of the cutting tool with either hand to hold down or support the workpiece, remove wood scraps, or for any other reason. Avoid awkward operations and hand positions where sudden slip could cause fingers or hand to move into a sawblade or other cutting tool.

•DO NOT perform any operation “FREEHAND” — always use either the rip fence or the miter gauge to position and guide the work.

•NEVER use the rip fence when crosscutting or the miter gauge when ripping. DO NOT use the rip fence as a length stop.

•NEVER hold onto or touch the “free end” of the workpiece or a “free piece” that is cut off, while power is “ON” and/or the sawblade is rotating.

•Shut “OFF” the saw and disconnect the power cord when removing the table insert, changing the cutting tool, removing or replacing the blade guard, or making adjustments.

•Provide adequate support to the rear and sides of the saw table for wider or long workpieces.

•Plastic and composition (like hardboard) materials may be cut on your saw. However, since these are usually quite hard and slippery, the anti-kickback pawls may not stop a kick- back. Therefore, be especially attentive to following proper set-up and cutting procedures for ripping. Do not stand, or permit anyone else to stand, in line with a potential kickback.

f. If you stall or jam the sawblade in the workpiece, turn saw “OFF”, remove the workpiece from the sawblade, and check to see if the sawblade is parallel to the table slots or grooves and if the spreader is in proper alignment with the sawblade. If ripping at the time, check to see if rip fence is parallel with the sawblade. Readjust as indicated.

g. NEVER gang crosscut — lining up more than one work- piece in front of the blade (stacked vertically, or horizontally outward on the table) and then pushing thru sawblade. The blade could pick up one or more pieces and cause a binding or loss of control and possible injury.

h. DO NOT remove small pieces of cut-off material that may become trapped inside the blade guard while the saw is running. This could endanger your hands or cause a kick- back. Turn saw “OFF” and wait until blade stops.

11. KNOW YOUR CUTTING TOOLS

Dull, gummy or improperly sharpened or set cutting tools can cause material to stick, jam, stall the saw, or kickback at the operator. Minimize potential injury by proper cutting tool and machine maintenance. NEVER ATTEMPT TO FREE A STALLED SAWBLADE WITHOUT FIRST TURNING THE SAW OFF.

a. NEVER use grinding wheels, abrasive cut-off wheels, fric- tion wheels (metal slitting blades) wire wheels or buffing wheels.

b. USE ONLY RECOMMENDED ACCESSORIES.

c. Crosscutting operations are more conveniently worked and with greater safety if an auxiliary wood facing is attached to the miter gauge. (See Page 64).

d. Make sure the top of the cutting tool rotates toward you when standing in normal operating position. Also make sure the cutting tool, arbor collars and arbor nut are installed prop- erly. Keep the cutting tool as low as possible for the oper- ation being performed. Keep all guards in place whenever possible.

•Do not use any blade or other cutting tool marked for an operating speed less than 4800 R.P.M. Never use a cutting tool larger in diameter than the diameter for which the saw was designed. For greatest safety and efficiency when rip- ping, use the maximum diameter blade for which the saw is designed, since under these conditions the spreader is near- est the blade.

e. Make sure the table insert is flush or slightly below the table surface on all sides except for rear side. NEVER oper- ate the saw unless the proper insert is installed.

NOTE AND FOLLOW SAFETY INSTRUCTIONS THAT APPEAR

ON THE FRONT OF YOUR TABLE SAW.

4.

Page 3 Page 5
Page 4
Image 4
Bosch Appliances 4100-09, 4100DG manual Know Your Cutting Tools
Page 3 Page 5

4100DG, 4100-09, 4100 specifications

Bosch Appliances 4100, 4100-09, and 4100DG are a series of highly regarded kitchen appliances designed to enhance efficiency and performance in home cooking. Bosch has a long-standing reputation for crafting high-quality products, and this series is no exception. Each model combines cutting-edge technology with sleek design to meet the needs of modern households.

A standout feature of the Bosch 4100 series is its powerful performance. These appliances come equipped with high-performance motors and advanced cooking capabilities that ensure consistent results. Whether baking, broiling, or roasting, users can expect even heat distribution and precise temperature control, which are critical for achieving culinary perfection.

The 4100 appliances also emphasize intuitive usability, featuring easy-to-navigate controls and thoughtful design. The models include user-friendly digital displays and simple button interfaces, making it easy for anyone, regardless of cooking experience, to operate them seamlessly. Additionally, the Bosch 4100 series is designed with a focus on safety, incorporating advanced systems that prevent overheating and ensure secure operation.

In terms of design, the Bosch 4100 models boast a streamlined aesthetic that blends well with any kitchen décor. Constructed from high-quality materials, they offer durability while exuding a modern, sophisticated look. The stainless-steel finishes not only add elegance but are also easy to clean and maintain, making them practical for everyday use.

Another noteworthy characteristic of the Bosch 4100 series is the energy efficiency standards they meet. These appliances are designed to utilize less energy without compromising performance, helping homeowners save on utility bills while minimizing their environmental footprint.

The 4100DG model specifically stands out for its dual-fuel capabilities, allowing users to harness the benefits of both gas and electric cooking methods. This versatility provides chefs with greater flexibility and precision, accommodating a variety of cooking styles and preferences.

Overall, Bosch Appliances 4100, 4100-09, and 4100DG exemplify craftsmanship and innovation in the kitchen appliance sector. Their combination of advanced technology, user-friendly features, and stylish designs make them an excellent choice for anyone looking to elevate their cooking experience and enhance their kitchen functionality.
Top Page Image Contents