reverse, the guard can be easily removed for special operations such as dados or rabbets.

The Anti-Kickback Device can be easily attached by aligning the attachment pin with the hole in the rear of the riving knife. It can be easily removed by depressing the compression pads on either side of the Anti-Kickback Device and lifting it away.

The Riving Knife can be easily adjusted to one of three heights by removing the table insert, raising the blade to its full height and releasing the riving knife release lever at the base of the Riving Knife. The Riving Knife should be locked in its highest position for use with the Main Barrier Guard and Anti-Kickback Device. It can be adjusted to its middle position for non-through cuts and for use as a material splitter without the Main Barrier Guard and Anti-Kickback Device.

In the event that the Riving Knife can not be used for a specific cut, it can be adjusted to its lowest position, thus placing it 1” above the surface of the table (while the blade is at its full height).

System Storage

1

FIG. 33

2

 

When not in use, the Main Barrier Guard and Anti-Kickback Device can be stored under the right side table extension.

!

WARNING

Use of all the components of the Smart Guard

System, including Main Barrier Guard, Anti-

 

 

Kickback Device, and Riving Knife is highly recommended to provide protection against accidents and injury.

FIG. 34

4

3

1.Slide the Main Barrier Guard assembly (upside down) up and back into the U-bracket at the rear right side of the saw (Fig. 33).

2.Pivot the rear of the guard up and into the front mounting bracket.

3.Lock the Main Barrier Guard assembly into place in the same manner as you would attach it to the Riving Knife (Fig. 34).

4.Attach the Anti-Kickback Device to the hanging bracket in the same manner that it attaches to the Riving Knife.

Blade Bevel Control

Loosen blade bevel lock handle 1 counterclockwise (Fig. 35), slide the elevation wheel 2 until pointer 3 is at desired angle and tighten blade tilt lock handle 1 clockwise.

Extending Table Extension

To extend the table, raise the table extension lock handle 4 (Fig. 35) and slide table extension 5 to desired width (Fig 36). To secure table setting, lower the lock handle 4.

3 1

FIG. 35

4

2

FIG. 36

5

46.

Page 45 Page 47
Page 46
Image 46
Bosch Appliances 4100-09, 4100DG manual Blade Bevel Control, Extending Table Extension, System Storage
Page 45 Page 47

4100DG, 4100-09, 4100 specifications

Bosch Appliances 4100, 4100-09, and 4100DG are a series of highly regarded kitchen appliances designed to enhance efficiency and performance in home cooking. Bosch has a long-standing reputation for crafting high-quality products, and this series is no exception. Each model combines cutting-edge technology with sleek design to meet the needs of modern households.

A standout feature of the Bosch 4100 series is its powerful performance. These appliances come equipped with high-performance motors and advanced cooking capabilities that ensure consistent results. Whether baking, broiling, or roasting, users can expect even heat distribution and precise temperature control, which are critical for achieving culinary perfection.

The 4100 appliances also emphasize intuitive usability, featuring easy-to-navigate controls and thoughtful design. The models include user-friendly digital displays and simple button interfaces, making it easy for anyone, regardless of cooking experience, to operate them seamlessly. Additionally, the Bosch 4100 series is designed with a focus on safety, incorporating advanced systems that prevent overheating and ensure secure operation.

In terms of design, the Bosch 4100 models boast a streamlined aesthetic that blends well with any kitchen décor. Constructed from high-quality materials, they offer durability while exuding a modern, sophisticated look. The stainless-steel finishes not only add elegance but are also easy to clean and maintain, making them practical for everyday use.

Another noteworthy characteristic of the Bosch 4100 series is the energy efficiency standards they meet. These appliances are designed to utilize less energy without compromising performance, helping homeowners save on utility bills while minimizing their environmental footprint.

The 4100DG model specifically stands out for its dual-fuel capabilities, allowing users to harness the benefits of both gas and electric cooking methods. This versatility provides chefs with greater flexibility and precision, accommodating a variety of cooking styles and preferences.

Overall, Bosch Appliances 4100, 4100-09, and 4100DG exemplify craftsmanship and innovation in the kitchen appliance sector. Their combination of advanced technology, user-friendly features, and stylish designs make them an excellent choice for anyone looking to elevate their cooking experience and enhance their kitchen functionality.
Top Page Image Contents