Non Thru-Sawing

Add 8" high flat facing board to the fence, the full length of the

fence (Fig. 66).

 

 

Use featherboards for all “Non Thru-Sawing” operations (when

 

 

sawblade guard must be removed). Featherboards 1 are used to

 

 

FIG. 66

keep the work in contact with the fence and table as shown, and to

 

 

stop kickbacks.

WORK SUPPORT

Mount featherboards 1 to fence and table as shown, so that

SUPPORT

leading edges of featherboards will support workpiece until cut is

APOYO DE LA

complete, and the workpiece has been pushed completely past the

PIEZA DE TRABAJO

cutter (sawblade, dado head, molding head, etc.) with a Push Stick

 

 

2, as in ripping.

 

 

Before starting the operation (switch saw “OFF” and set cutter

 

 

below table surface):

 

 

A. Install featherboards so they exert pressure on the workpiece;

 

 

BE POSITIVE THEY ARE SECURELY ATTACHED.

 

 

B. Make sure by trial that the featherboards will stop a kickback if

 

 

one should occur.

 

 

Featherboards are not employed during non thru-sawing

 

 

operations when using the miter gauge.

 

 

REPLACE THE SMART GUARD SYSTEM AS SOON AS THE

 

 

NON THRU-SAWING OPERATION IS COMPLETE.

 

 

Rabbeting

RABBETING is known as cutting out a section of the corner of a

piece of material, across an end or along an edge (Fig. 67).

 

 

 

Making a RABBET requires cuts which do not go all the way

 

 

 

through the material. Therefore the Smart Guard System must be

 

 

 

removed.

 

 

 

1. Remove blade guard.

 

 

 

2. For rabbeting along an edge (long way of workpiece) as shown,

 

 

 

 

FIG. 67

add facing to rip fence approximately as high as the workpiece is

 

 

 

wide. Adjust rip fence and blade to required dimensions; then

 

 

 

make first cut with board flat on table, follow set-up Fig. 66. Make

 

RABBET

second cut with workpiece on edge. Follow all precautions,

 

FEUILLURE

safety instructions, and operation instructions as for ripping or rip

 

REBAJO

type operations, including featherboards and Push Stick, etc.

 

 

 

 

3. For rabbeting across an end, for workpiece 10-1/2" and narrower

 

 

 

make the rabbet cut with the board flat on the table. Using the

 

 

 

miter gauge fitted with a facing, follow the same procedures and

 

 

 

instructions for crosscutting making successive cuts across the

 

 

 

width of the workpiece to obtain the desired width of cut. DO

 

 

 

NOT use the rip fence for rabbeting across the end.

 

 

 

“C” CLAMPS

 

SERRE-JOINTS EN C

 

ABRAZADERAS EN “C”

1

 

2

1

FIRST CUT

PREMIÈRE COUPE

PRIMER CORTE

SECOND CUT

DEUXIÈME COUPE

SEGUNDO CORTE

4.INSTALL SMART GUARD SYSTEM IMMEDIATELY UPON COMPLETION OF RABBETING OPERATION.

Rabbet cuts can also be made in one pass of the workpiece over the cutter using the dado head or molding head.

RABBETING ALONG

RABBETING ACROSS

THE EDGE

THE END

RÉALISATION D’UNE

RÉALISATION D’UNE

FEUILLURE LE LONG D’UN

FEUILLURE EN TRAVERS

BORD

D’UNE EXTRÉMITÉ

REBAJO A LO LARGO

REBAJO TRANSVERSAL

DEL BORDE

AL EXTREMO

76.

Page 75 Page 77
Page 76
Image 76
Bosch Appliances 4100-09, 4100DG manual Non Thru-Sawing, Rabbeting, Be Positive They are Securely Attached
Page 75 Page 77

4100DG, 4100-09, 4100 specifications

Bosch Appliances 4100, 4100-09, and 4100DG are a series of highly regarded kitchen appliances designed to enhance efficiency and performance in home cooking. Bosch has a long-standing reputation for crafting high-quality products, and this series is no exception. Each model combines cutting-edge technology with sleek design to meet the needs of modern households.

A standout feature of the Bosch 4100 series is its powerful performance. These appliances come equipped with high-performance motors and advanced cooking capabilities that ensure consistent results. Whether baking, broiling, or roasting, users can expect even heat distribution and precise temperature control, which are critical for achieving culinary perfection.

The 4100 appliances also emphasize intuitive usability, featuring easy-to-navigate controls and thoughtful design. The models include user-friendly digital displays and simple button interfaces, making it easy for anyone, regardless of cooking experience, to operate them seamlessly. Additionally, the Bosch 4100 series is designed with a focus on safety, incorporating advanced systems that prevent overheating and ensure secure operation.

In terms of design, the Bosch 4100 models boast a streamlined aesthetic that blends well with any kitchen décor. Constructed from high-quality materials, they offer durability while exuding a modern, sophisticated look. The stainless-steel finishes not only add elegance but are also easy to clean and maintain, making them practical for everyday use.

Another noteworthy characteristic of the Bosch 4100 series is the energy efficiency standards they meet. These appliances are designed to utilize less energy without compromising performance, helping homeowners save on utility bills while minimizing their environmental footprint.

The 4100DG model specifically stands out for its dual-fuel capabilities, allowing users to harness the benefits of both gas and electric cooking methods. This versatility provides chefs with greater flexibility and precision, accommodating a variety of cooking styles and preferences.

Overall, Bosch Appliances 4100, 4100-09, and 4100DG exemplify craftsmanship and innovation in the kitchen appliance sector. Their combination of advanced technology, user-friendly features, and stylish designs make them an excellent choice for anyone looking to elevate their cooking experience and enhance their kitchen functionality.
Top Page Image Contents