Bosch Appliances D9412GV3 manual Phone Parameters, Phone # Format, Point/User Flag

D9412GV3/D7412GV3 Program Entry Guide 2.0 Panel and Area Wide Parameters

EN 14

2.2Phone Parameters

The program items in this category describe panel- wide characteristics for telephone dialing, receiver format, and supervision.

Phone # Format

Default:	Modem IIIa2
Selection:	Modem IIIa2 or Contact ID
Modem IIIa2	Modem IIIa2 Communication Format
Contact ID	ANSI-SIA Contact ID

Central Station Receiver Format for Transmission of Reports: Modem format provides many reporting advantages over the Contact ID format. Refer to the D6500 Report Directory (P/N: 74-04651-001) for more information about the effect of reporting formats.

Reports identify points as 001 through 247 and passcode User ID codes as 000 through 249 at the D6500 or D6600 Receiver (unless Point/User Flag is programmed Yes; refer to the Point/User Flag prompt in this section). When reporting point events, Modem IIIa2 Communication Format also sends point text to the D6500 or D6600 as programmed in Point Assignments.

Keypad Programming of Phone # Format

D1255

1.Refer to Figure 1 on page 7 to access Keypad Programming and navigate to the PHONE PARAMETERS option.

2.At the PHONE 1 - 4 prompt, enter the phone route number you wish to configure and press [ENT].

3.Press [NEXT] or [PREV] to toggle between Contact ID and ModemIIIa2 and press [ENT] to select the desired phone format.

When the keypad reads PARAMETER SAVED, your selection has been configured.

D1260

1.Refer to Figure 2 on page 8 to access Keypad Programming and navigate to the Phone Parameters option and press the corresponding softkey.

2.At the Phone (1-4)prompt, enter the phone route number you wish to configure and press [ENTER]. The current configuration shows.

3.Press the Edit softkey to change the phone format.

4.Select the softkey for the option to which you wish to change. Press the Save softkey

When the keypad reads Parameter Saved, your selection has been configured.

Point/User Flag

Default:	Yes
Selection:	Yes or No
Yes	The control panel sends a flag with
	each report telling the D6500 or
	D6600 to convert point numbers and
	User ID numbers to COMEX format.
	Refer to Table 5 and Table 6 for
	conversion information. When this
	parameter is programmed Yes,
	points and User ID numbers are
	converted, regardless of the
	programming of the D6500 or D6600
	Receiver for output to the computer
	system. Refer to Appendix C in the
	Conettix D6600/D6100
	Receiver/Gateway Computer
	Interface Manual (P/N: 4998122703).
No	The control panel does not send the
	flag. The D6500 or D6600 outputs
	point numbers as 001 to 247 (rather
	than 100 to 732) and User ID
	numbers as 000 to 249 (rather than
	000 to F08), as indicated in Table 5
	and Table 6.

This program item determines how point and User ID numbers are presented at the D6500 or D6600 display, printer, and computer RS-232 output.

When Phone # Format is Yes, the control panel sends expanded Bosch Modem IIIa2 Communication Format reports to the D6500 or D6600. If your central station data files are not set up for point and User ID number reporting, you can use this program item to convert these numbers to COMEX Reports.

When Phone # Format is Yes, the control panel sends expanded Bosch Modem IIIa2 Communication Format Reports to the receiver. Point/User Flag affects Bosch Modem IIIa2 Communication Format data as shown in Table 5. The Bosch Security Systems, Inc. D6500 or D6600 Receiver adds the leading zero in the User ID number with Point/User Flag programmed No.

Bosch Security Systems, Inc. 10/11 F01U170807-02