Bosch Appliances D9412GV3 manual Programming Primary and Backup Destinations, Enhanced Routing

D9412GV3/D7412GV3 Program Entry Guide 2.0 Panel and Area Wide Parameters

EN 18

2.3.3Programming Primary and Backup Destinations

Each route number has an R# Primary Device and an R# Backup Device. For example, if two phone numbers are programmed, the R# Primary Device destination is the phone number that the route group attempts to dial first. If the R# Primary Device destination does not connect to the central station receiver after two dialing attempts, the control panel dials the R# Backup Device destination.

You can also program the control panel so that the R# Primary Device or the R# Backup Device uses an SDI device, such as a Network Interface Module.

With enhanced communications, the R# Primary Device destination can be either the phone number or the path number for the SDI device, to which the route group first attempts to send the event. If the R# Primary Device destination fails to connect to the central station receiver after two attempts, the control panel attempts to connect with the R# Backup Device destination.

2.3.4Enhanced Routing

The D9412GV3 and D7412GV3 allow events to be sent to up to four additional SDI Paths. The network interface modules (NIMs) connect directly to the SDI Bus and occupy SDI Address 88 or 92. For additional information regarding the specific programming requirements for enhanced communications, refer to Section 5.5 Programming Path Numbers and IP Addresses for Enhanced Communications on page 131.

2.3.5Programming a Duplicate Report

Select Yes for each available route number to allow an event within a group to send a report to multiple groups. For instance, if fire alarms are programmed for Route Group 1 and Route Group 2, a fire alarm sends a report first to Route Group 1, followed by a duplicate report to Route Group 2.

2.3.6Routing Destination Communication Failures

When the R# Primary Device fails to connect to the central station receiver after two attempts by phone, the R# Backup Device phone number will be dialed. The central station will receive the original event with a COMM TROUBLE PHONE # = (1, 2, 3, or 4) message

added. This event does not occur if there is no backup phone number. If the R# Primary Device is an SDI Path, the central station receives the original event with a COMM TROUBLE RG8 SDI## event modifier. Refer to Table 8 on page 18.

Table 8: SDI Path Number by Device

Path	1	2	3	4
SDI 88	88	89	90	91
SDI 92	92	93	94	95

When all attempts to both the R# Primary Device and R# Backup Device fail, a COMM FAIL RG# event is generated. COMM RESTORE RG# events are generated when a successful report (via phone or IP) or a successful poll (via IP) is sent over either route within the failed Route Group, even if the report is sent using a different Route Group.

The same COMM TROUBLE conditions occur if the control panel does not receive a positive acknowledgement to a poll from the central station receiver after the configured number of retries. Refer to Path # Poll Rate on page 132.

2.3.7Message Prioritization within a Route Number

The D9412GV3/D7412GV3 Control Panels meet the digital reporting requirements for UL 864. Fire Alarm Events have the highest priority and reports are sent first for each group. Other events are sent in the following order: Panic, Duress, Medical, Intrusion Alarm, Supervisory, and all troubles and restorals.

To comply with NFPA and UL 864 , program Route 1 to send a report of only Fire Alarm Events to ensure the fastest reporting time.

2.3.8Communication Attempts

The control panel makes up to ten communication attempts using the primary and backup devices within a route group. If unsuccessful, it sends a Comm Fail Report. The communication attempts occur in the following sequence:

1.Primary device

2.Primary device

3.Backup device

4.Backup device

5.Primary device

6.Backup device

7.Primary device

8.Backup device

9.Primary device

10.Backup device

When only one destination is programmed, the control panel makes ten attempts to contact that destination. When reporting via phone, each group takes approximately 10 min to go into Comm Fail.

Bosch Security Systems, Inc. 10/11 F01U170807-02