Bosch Appliances D9412GV3 manual User Interface, Example

D9412GV3/D7412GV3 Program Entry Guide 2.0 Panel and Area Wide Parameters

EN 59

128 to 143 Enable Custom Function 128 through 143 (Menu Function only): This function determines if a passcode is needed to access a Custom Function from the menu list. ENTER PASSCODE (or Enter Passcode + Enter Key on the D1260) appears when this function is passcode protected.

If a command within the Custom Function is passcode protected, ENTER PASSCODE appears at the keypad. The user must enter a valid passcode before proceeding with the rest of the Custom Function. If a passcode is not entered within 10 sec, the Custom Function times out and the display returns to idle text.

Skeds cannot execute Custom Functions that are passcode protected. The D720 LED keypad does not support Custom Functions that are passcode protected.

Some functions cannot be entered directly because they are nested inside a higher-level function. To automatically execute these functions, you must add the appropriate keystrokes.

For example: The Change Display (COMMAND

49) function has three sub-functions: Bright Display, Dim Display, and Date/Time Display.

-To turn up the display, enter: [A][4][9][E]

-To dim the display, enter: [A][4][9][D][E]

-To display time and date, enter: [A][4][9][B][E]

Custom Functions can perform several tasks at one time. For example:

 To toggle relays 7, 8, and 9 in one Custom Function enter:

[A] [5] [4] [7] [E] [E] [8] [E] [E] [9] [E] [E] [C]

To add a temporary passcode, enter:

[A][5] [6] [3] [0] [E] [E] [9] [8] [7] [E] [E] [D] [E]

[1] [E] [1] [E] [1] [E] [1] [E] [1] [E] [1] [E] [1] [E]

[1] [E] [C]

This adds user 30, passcode 987 with authority level 1 in all areas.

To delete the passcode, enter:

[A][5] [3] [3] [0] [E] [E] [E] [C]

To program multiple-area Arming or Disarming functions, use keystroke sequences including COMMAND 50 (Move to Area) and COMMAND 1.

Custom function cannot be used to change time (such as Daylight Saving Time). Use Skeds S## Function Codes 13 and 14 to adjust for Daylight Saving Time (refer to S## Custom Function prompt in Section 4.2 Schedules (Skeds) on page 114.

Example 1

Execute the third function in a keypad menu function list:

D1255 CDDE

D1260 C8C7C5

The custom functions in Example 1 are not compatible between keypad types.

Example 2

Instant master Arm (CMD 11):

D1255 A11

D1260 A11

The custom functions in Example 2 are compatible between keypad types.

The GV3 control panel series uses separate keystrokes to program the custom functions that accurately represent the two separate user interfaces, the D1255 and D1260 keypads.

Custom functions written for the D1255 that use the [PREV], [ESC], and [NEXT] keys do not work on the D1260.

Custom function written for the D1260 that use the softkeys (located on the sides of the keypad display) do not work when executed from the D1255 keypad.

2.10User Interface

Define which functions can be used by each of the fourteen user authority levels. Each user can be assigned the same or different authority level by area. The user has rights in the area where the keypad is assigned, based on the authority level assigned to the user’s passcode for that area.

When the passcode is entered at the keypad, the control panel checks the authority level. The control panel executes the function only in areas where the passcode has the authority to use the function.

Bosch Security Systems, Inc. 10/11 F01U170807-02