! WARNING
! WARNING

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 32

dAdO CUTTINg

Instructions for operating the saw with Dado Head sets are contained in the booklet furnished with these accessories.

ALWAYS USE AN APPROPRIATE BOSCH TABLE INSERT AND WASHERS LISTED UNDER REC- OMMENDED ACCESSORIES (see page 35).

ALWAYS PLACE THE BLADE WASHERS IN THE ORIGINAL POSITIONS WHEN YOU ARE FIN- ISHED DADO CUTTING.

INSTAllINg A dAdO SET

A dado set is an accessory system used to make non-thru grooves or lap cuts on work pieces. These tools are commonly used in furniture and cabinet building. After work pieces have been properly dado cut, they can be tightly joined together. The GTS1031 table saw can accommodate dado cutting up to 1/2” wide in a single pass.

To reduce the risk of injury, al- ways disconnect plug from

power source before changing blades.

To reduce the risk of injury, al- ways use the bosch dado blade Table Insert No.TS1013 (comes with a dado ac-

cessory washer). Never make dado cuts without this insert. Do not use dado sets larger than 8” di- ameter. Never set dado cutters to any bevel angle other than the vertical 0° angle. Follow all warnings and instructions shown here and those that accom- pany your dado set. Failure to comply with these warnings may result in serious bodily injuries.

! WARNING

To reduce the risk of injury, do

 

not use dado sets larger than 8

 

inches in diameter. The saw is not designed to ac- cept larger sized dados.

USINg STACKEd dAdO SETS

NOTE: These instructions are based on using the

Bosch 8” and 6” Professional Dado Sets: Model Nos. PRO824DADO, PRO840DADO and PRO624DADO. They also apply to most standard stacked dado sets.

1.Disconnect plug from power source.

2.Remove the Barrier Guard Assembly and Anti- Kickback Device (see pages 12 & 13). Lower and lock the Riving Knife in its lowest position.

3.Remove standard table insert plate. Raise saw blade to maximum height.

4.Remove the arbor nut, then outer washer, and saw blade, (see page 15). Note: For only dado cutting, leave the inner washer in place. The outer washer will be replaced with the combination nut/washer included with the TS1013 insert.

5.Installing a dado stack (Fig. 55)

A)Place the desired parts of the dado set onto the arbor shaft.

B)Place the desired parts of the dado set onto the arbor shaft.

C)Place the supplied combination nut/washer from the Dado Accessory Kit (TS1013) onto the outside of the dado stack and tighten.

6. Placing dado blades and chippers: (see Fig. 55)

For 1/4” wide cuts, place the two outside dado blades (cutters) on the shaft. The two dado out- side blades may be different, check for informa- tion on the blade and the manufacturer's instructions for proper installation.

For wider cuts (up to 1/2” maximum), chipper blades and spacers can be placed only between the outside blades (cutters).

FIG. 55

INNER BLADE

 

 

WASHER

COMBINATION

 

 

 

 

NUT/WASHER

 

ARBOR

 

INNER BLADE

OUTER BLADE

CHIPPERS

-32-

Page 32
Image 32
Bosch Power Tools GTS1031 manual DAdO CUTTINg, INSTAllINg a dAdO SET, Power source before changing blades

GTS1031 specifications

The Bosch Power Tools GTS1031 is a compact job site table saw designed to deliver precision cutting in a portable format. This powerful saw is equipped with a robust 15-amp motor that can easily handle a wide variety of applications, making it an excellent choice for contractors and DIY enthusiasts alike.

One of the standout features of the GTS1031 is its Smart Guard System. This integrated safety feature includes a modular blade guard, riving knife, and anti-kickback pawls. The blade guard helps protect the user from accidental contact with the blade, while the riving knife reduces the risk of kickback during operation. The entire system is designed to be easy to install and adjust, promoting both safety and efficiency on the job.

The GTS1031 boasts a portable, lightweight design that weighs just 52 pounds. This makes it easy to transport, set up, and store. Its foldable stand provides a stable base while offering simple setup and breakdown without the need for additional tools. The compact size of the saw, along with its sturdy construction, makes it extremely convenient for use in tight spaces or on busy job sites.

Another notable characteristic of the GTS1031 is its cutting capacity. With a 10-inch blade, it can make cuts up to 26 inches wide with a depth of 3.5 inches at 90 degrees and 2.5 inches at 45 degrees. The precision machined aluminum table ensures accurate cuts and durability, while the integrated measurements allow for easy adjustments and repeatability.

The saw features an onboard storage system for its accessories, ensuring that everything needed for operation is within arm's reach. This organization helps users stay efficient, reducing downtime during projects. The table saw is also designed for easy blade changes, minimizing interruption and allowing users to switch between different types of blades based on their cutting needs.

With its blend of power, portability, and safety features, the Bosch Power Tools GTS1031 stands out as a reliable choice for both professionals and hobbyists. Its emphasis on precision and user-friendly design makes it an indispensable tool for a wide range of applications, from framing to fine woodworking.