BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 18

AdjUSTINg blAdE pARAllEl TO

FIG. 20

THE MITER gAUgE SlOTS

 

The blade was adjusted parallel to the miter gauge

 

slots at the factory. In order to insure accurate cuts

 

and help prevent kickback, this adjustment should

 

be rechecked. If adjustment is necessary, follow

 

the steps below.

 

To prevent personal injury, al- ! WARNING ways disconnect the plug from

power source before making any adjustments.

1.Turn elevation wheel and raise blade as high as it will go.

2.Select a point on the body of the saw blade that is set to the left when viewing blade from the front of saw, and mark 1 with a pencil (Fig. 20).

3.Place the base of a combination square against the edge of the miter gauge slot, and extend the

sliding rule of square so it just touches the marked point 1 on the body of the saw blade at the rear of the table.

4.Rotate blade and check the same marked point 1 of the saw blade at the front of the table (Fig. 20).

5.If the front and back measurements, shown in Figure 20, are not identical, loosen the four alignment bolts 2, located on the underside of the table at the front and rear of the saw with hex wrench supplied with your saw (Fig. 21 & 22). Carefully move the saw blade until the blade is parallel to the miter gauge slot, and se- curely tighten all four bolts.

1

FIG. 21

 

UNDER FRONT

2

OF TABLE

 

FIG. 22

UNDER REAR OF TABLE

2

-18-

Page 17 Page 19
Page 18
Image 18
Bosch Power Tools GTS1031 AdjUSTINg blAdE pARAllEl to Miter gAUgE SlOTS, Blade was adjusted parallel to the miter gauge
Page 17 Page 19

GTS1031 specifications

The Bosch Power Tools GTS1031 is a compact job site table saw designed to deliver precision cutting in a portable format. This powerful saw is equipped with a robust 15-amp motor that can easily handle a wide variety of applications, making it an excellent choice for contractors and DIY enthusiasts alike.

One of the standout features of the GTS1031 is its Smart Guard System. This integrated safety feature includes a modular blade guard, riving knife, and anti-kickback pawls. The blade guard helps protect the user from accidental contact with the blade, while the riving knife reduces the risk of kickback during operation. The entire system is designed to be easy to install and adjust, promoting both safety and efficiency on the job.

The GTS1031 boasts a portable, lightweight design that weighs just 52 pounds. This makes it easy to transport, set up, and store. Its foldable stand provides a stable base while offering simple setup and breakdown without the need for additional tools. The compact size of the saw, along with its sturdy construction, makes it extremely convenient for use in tight spaces or on busy job sites.

Another notable characteristic of the GTS1031 is its cutting capacity. With a 10-inch blade, it can make cuts up to 26 inches wide with a depth of 3.5 inches at 90 degrees and 2.5 inches at 45 degrees. The precision machined aluminum table ensures accurate cuts and durability, while the integrated measurements allow for easy adjustments and repeatability.

The saw features an onboard storage system for its accessories, ensuring that everything needed for operation is within arm's reach. This organization helps users stay efficient, reducing downtime during projects. The table saw is also designed for easy blade changes, minimizing interruption and allowing users to switch between different types of blades based on their cutting needs.

With its blend of power, portability, and safety features, the Bosch Power Tools GTS1031 stands out as a reliable choice for both professionals and hobbyists. Its emphasis on precision and user-friendly design makes it an indispensable tool for a wide range of applications, from framing to fine woodworking.
Top Page Image Contents