Bosch Power Tools GTS1031 manual Double Insulated Tools, Table of Contents

! WARNING

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 6

double Insulated Tools

Double insulation is a design concept used in electric power tools which eliminates the need for the three wire grounded power cord and grounded power supply system. It is a recognized and ap- proved system by Underwriter’s Laboratories, CSA and Federal OSHA authorities.

IMpORTANT: Servicing of a tool with double insu- lation requires care and knowledge of the system and should be performed only by a qualified service technician.

WHEN SERVICING, USE ONLY IDENTICAL RE- PLACEMENT PARTS.

POLARIZED PLUGS. To reduce the risk of electri- cal shock, your tool is equipped with a polarized plug (one blade is wider than the other), this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. To reduce the risk of electrical shock, do not change the plug in any way.

EXTENSION CORdS

Replace damaged cords immedi- ! WARNING ately. Use of damaged cords can

shock, burn or electrocute.

If an extension cord is necessary, a cord with adequate size conductors should be used to prevent excessive voltage drop,

loss of power or overheating. The table shows the correct size to use, depending on cord length and nameplate amperage rating of tool. If in doubt, use the next heavier gauge. Always use U.L. and CSA listed extension cords.

RECOMMENdEd SIZES Of EXTENSION CORdS 120 VOlT AlTERNATINg CURRENT TOOlS

Tool’s	Cord Size in A.W.g.				Wire Sizes in mm2
Ampere	Cord length in feet				Cord length in Meters
Rating	25	50	100	150	15	30	60	120
3-6
	18	16	16	14	0.75	0.75	1.5	2.5
6-8	18	16	14	12	0.75	1.0	2.5	4.0
8-10	18	16	14	12	0.75	1.0	2.5	4.0
10-12	16	16	14	12	1.0	2.5	4.0	—
12-16	14	12	—	—	—	—	—	—

NOTE: The smaller the gauge number, the heavier the cord.

“SAVE THESE INSTRUCTIONS”

Table of Contents

	Page		Page
General Safety Rules	. . . .2	Table Insert	. . . . .9
Additional Safety Rules	. .3–5	Table	. . . .10
Double Insulated Tools & Extension Cords	. . . .6	Miter Gauge	. . . .10
Table of Contents	. .6-7	Cord Wrap	. . . .10
Glossary of Terms	. .7-8	Rip Fence Storage	. . . .10
Tools Needed For Assembly	. . . .8	Push Stick & Wrench Storage	. . . .10
Getting To Know Your Table Saw	.9, 10	One-Handed Carry Handle	. . . .10
Power Switch	. . . .9	Smart Guard System Storage	. . . .10
Elevation Wheel	. . . .9	Dust Port/Vacuum Hook-Up	. . . .10
Blade Bevel Lock Handle	. . . .9	Anti-Kickback Device Storage	. . . .10
Blade Bevel Scale	. . . .9	Miter Gauge Storage	. . . .10
Base	. . . .9	Hex Wrench & Storage compartment	. . . .10
Table Extension Lock Handle	. . . .9	Stand Attachment Bracket	. . . .10
Push Stick	. . . .9	Unpacking and Checking Contents	. . . .11
Table Extension	. . . .9	Table of Loose Parts	. . . .11
Rip Fence	. . . .9	Assembly	.12–16
Rip Fence Scale	. . . .9	Attaching Smart Guard
Smart Guard System	. . . .9	System Components	.12, 13

-6-