BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 31

NON THRU-SAWINg

Add 8" high flat facing board to the fence, the full length of the fence (Fig. 53).

Use featherboards for all “Non Thru-Sawing” oper- ations (when sawblade guard must be removed). Featherboards 1 are used to keep the work in con- tact with the fence and table as shown, and to stop kickbacks.

Mount featherboards 1 to fence and table as shown, so that leading edges of featherboards will support workpiece until cut is complete, and the workpiece has been pushed completely past the cutter (saw- blade, dado head, etc.) with a Push Stick 2, as in ripping.

Before starting the operation (switch saw “OFF” and set cutter below table surface):

cuts across the width of the workpiece to obtain the desired width of cut. DO NOT use the rip fence for rabbeting across the end.

4.INSTALL SMART GUARD SYSTEM IMMEDI- ATELY UPON COMPLETION OF RABBETING OPERATION.

Rabbet cuts can also be made in one pass of the workpiece over the cutter using the dado head.

FIG. 53

“C” CLAMPS

1

 

WORK

SUPPORT

A. Install featherboards so they exert pressure on the workpiece; BE POSITIVE THEY ARE SE-

CURELY ATTACHED.

B.Make sure by trial that the featherboards will stop a kickback if one should occur.

2

Featherboards are not employed during non thru- sawing operations when using the miter gauge.

REPLACE THE SMART GUARD SYSTEM AS

 

SOON AS THE NON THRU-SAWING OPERATION

 

IS COMPLETE.

1

RAbbETINg

RABBETING is known as cutting out a section of the

 

corner of a piece of material, across an end or along

 

an edge (Fig. 54).

 

Making a RABBET requires cuts which do not go all

 

the way through the material. Therefore the Smart

FIG. 54

Guard System must be removed.

FIRST CUT

 

1. Remove blade guard.

 

2.For rabbeting along an edge (long way of work- piece) as shown, add facing to rip fence approxi- mately as high as the workpiece is wide. Adjust rip fence and blade to required dimensions; then make first cut with board flat on table, follow set- up Fig. 53. Make second cut with workpiece on edge. Follow all precautions, safety instructions, and operation instructions as for ripping or rip type operations, including featherboards and Push Stick, etc.

3.For rabbeting across an end, for workpiece 10- 1/2" and narrower make the rabbet cut with the board flat on the table. Using the miter gauge fit- ted with a facing, follow the same procedures and instructions for crosscutting making successive

RABBET

SECOND CUT

RABBETING ALONG

THE EDGE

RABBETING ACROSS

THE END

-31-

Page 30 Page 32
Page 31
Image 31
Bosch Power Tools GTS1031 Work Support, RAbbETINg, First CUT, Rabbet Second CUT Rabbeting Along Edge Rabbeting Across END
Page 30 Page 32

GTS1031 specifications

The Bosch Power Tools GTS1031 is a compact job site table saw designed to deliver precision cutting in a portable format. This powerful saw is equipped with a robust 15-amp motor that can easily handle a wide variety of applications, making it an excellent choice for contractors and DIY enthusiasts alike.

One of the standout features of the GTS1031 is its Smart Guard System. This integrated safety feature includes a modular blade guard, riving knife, and anti-kickback pawls. The blade guard helps protect the user from accidental contact with the blade, while the riving knife reduces the risk of kickback during operation. The entire system is designed to be easy to install and adjust, promoting both safety and efficiency on the job.

The GTS1031 boasts a portable, lightweight design that weighs just 52 pounds. This makes it easy to transport, set up, and store. Its foldable stand provides a stable base while offering simple setup and breakdown without the need for additional tools. The compact size of the saw, along with its sturdy construction, makes it extremely convenient for use in tight spaces or on busy job sites.

Another notable characteristic of the GTS1031 is its cutting capacity. With a 10-inch blade, it can make cuts up to 26 inches wide with a depth of 3.5 inches at 90 degrees and 2.5 inches at 45 degrees. The precision machined aluminum table ensures accurate cuts and durability, while the integrated measurements allow for easy adjustments and repeatability.

The saw features an onboard storage system for its accessories, ensuring that everything needed for operation is within arm's reach. This organization helps users stay efficient, reducing downtime during projects. The table saw is also designed for easy blade changes, minimizing interruption and allowing users to switch between different types of blades based on their cutting needs.

With its blend of power, portability, and safety features, the Bosch Power Tools GTS1031 stands out as a reliable choice for both professionals and hobbyists. Its emphasis on precision and user-friendly design makes it an indispensable tool for a wide range of applications, from framing to fine woodworking.
Top Page Image Contents