! WARNING

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 19

AlIgNINg RIp fENCE

! WARNING To prevent personal injury, always disconnect plug from power source

before making any adjustments. The rip fence must be parallel with the SAWBLADE in order to prevent KICKBACK when ripping.

Your table saw is equipped with a Self-Aligning, Squarelock™ rip fence. Once the adjustments below have been made, the rip fence will self align when the fence is locked into position.

NOTE: The blade must be parallel with the miter gauge slots (see page 18) and be perpendicular to table before proceeding with rip fence alignment.

To prevent personal injury, always make sure the rip fence is locked

before making rip cuts.

1.Lift both guard barriers 2 to their up locked posi- tion.

2.Raise lock handle 1 and slide fence 3 until it is alongside the sawblade, by lifting right side pawl 4 above fence (Fig. 23).

The fence should touch the blade teeth at the front and rear of the blade. If fence does not touch the teeth at front and rear of blade continue with the following the steps:

3.Loosen the two screws 5 on the top front section of the rip fence using the included 5mm hex wrench.

4.Move fence 3 until it touches the teeth and is parallel to the blade.

5.Hold fence in place and lower lock handle, check to make sure the fence stayed parallel to the blade then tighten screws (Fig. 23).

6.Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side.

RIp fENCE pOINTER AdjUSTMENT

The distance of the rip fence body from the blade when ripping on the right side of the blade is deter- mined by lining the pointer 7 with the desired dimen- sion on the scale 8 (Fig. 24).

TO SET THE RIp fENCE pOINTER:

1.Lift both guard barriers 2 to their up locked posi- tion (Fig. 23).

2.Raise lock handle 1 and slide fence 3 until it is alongside the sawblade, by lifting right side pawl 4 above fence. Lock fence in place (Fig. 23).

3.Loosen pointer adjustment screw 9, adjust pointer 7 to “0” mark on lower scale 8, then re-tighten screw 9 (Fig. 24).

FIG. 23

2

45

6 1

3

FIG. 24

7

8 9

-19-

Page 19
Image 19
Bosch Power Tools GTS1031 manual AlIgNINg RIp fENCE, RIp fENCE pOINTER AdjUSTMENT, To SET the RIp fENCE pOINTER

GTS1031 specifications

The Bosch Power Tools GTS1031 is a compact job site table saw designed to deliver precision cutting in a portable format. This powerful saw is equipped with a robust 15-amp motor that can easily handle a wide variety of applications, making it an excellent choice for contractors and DIY enthusiasts alike.

One of the standout features of the GTS1031 is its Smart Guard System. This integrated safety feature includes a modular blade guard, riving knife, and anti-kickback pawls. The blade guard helps protect the user from accidental contact with the blade, while the riving knife reduces the risk of kickback during operation. The entire system is designed to be easy to install and adjust, promoting both safety and efficiency on the job.

The GTS1031 boasts a portable, lightweight design that weighs just 52 pounds. This makes it easy to transport, set up, and store. Its foldable stand provides a stable base while offering simple setup and breakdown without the need for additional tools. The compact size of the saw, along with its sturdy construction, makes it extremely convenient for use in tight spaces or on busy job sites.

Another notable characteristic of the GTS1031 is its cutting capacity. With a 10-inch blade, it can make cuts up to 26 inches wide with a depth of 3.5 inches at 90 degrees and 2.5 inches at 45 degrees. The precision machined aluminum table ensures accurate cuts and durability, while the integrated measurements allow for easy adjustments and repeatability.

The saw features an onboard storage system for its accessories, ensuring that everything needed for operation is within arm's reach. This organization helps users stay efficient, reducing downtime during projects. The table saw is also designed for easy blade changes, minimizing interruption and allowing users to switch between different types of blades based on their cutting needs.

With its blend of power, portability, and safety features, the Bosch Power Tools GTS1031 stands out as a reliable choice for both professionals and hobbyists. Its emphasis on precision and user-friendly design makes it an indispensable tool for a wide range of applications, from framing to fine woodworking.