Manuals / Bryant / Household Appliance / Heating System

Bryant 580F Viii. — Adjust Factory-Installedoptions, A. Manual Outdoor-AirDamper

Models: 580F

1 80

Download 80 pages 29.14 Kb

Page 17

VIII. STEP 8 — ADJUST FACTORY-INSTALLED OPTIONS

VIII. STEP 8 — ADJUST FACTORY-INSTALLED OPTIONS

A. Manual Outdoor-Air Damper

The outdoor-air hood and screen are attached to the basepan at the bottom of the unit for shipping.

Assembly:

1.Determine quantity of ventilation required for build- ing. Record amount for use in Step 8.

2.Remove filter access panel by raising panel and swinging panel outward. Panel is now disengaged from track and can be removed. No tools are required to remove the filter access panel. Remove outdoor-air opening panel. Save panels and screws. See Fig. 12.

3.Separate hood and screen from basepan by removing the screws and brackets securing them. Save all screws and discard brackets.

4.Replace outdoor air opening panel with screws saved from Step 2.

5.Place hood on front of outdoor-air opening panel. See Fig. 13 for hood details. Secure top of hood with the 6 screws removed in Step 3. See Fig. 14.

6.Remove and save 6 screws (3 on each side) from sides of the manual outdoor-air damper.

7.Align screw holes on hood with screw holes on side of manual outdoor-air damper. See Fig. 13 and 14. Secure hood with 6 screws from Step 6.

8.Adjusting the manual outdoor-air adjustment screws on the front of the damper blade. See Fig. 12. Slide blade vertically until it is in the appropriate position determined by Fig. 15. Tighten screws.

9.Remove and save screws currently on sides of hood. Insert screens. Secure screens to hood using the screws. See Fig. 14.

10.Replace filter access panel. Ensure filter access panel slides along the tracks and is securely engaged.

OUTDOOR

AIR OPENING

PANEL

Fig. 13 — Outdoor-Air Hood Details

HOOD

NOT

SHOWN)

	3 SCREWS	Fig. 14 — Optional Manual Outdoor-Air Damper
	3 SCREWS	with Hood Attached
	(SIDE)	with Hood Attached

Fig. 12 — Damper Panel with Manual

Outdoor-Air Damper Installed

Fig. 15 — Outdoor-Air Damper Position Setting

—17—

Image 17

Bryant 580F Viii. — Adjust Factory-Installedoptions, A. Manual Outdoor-AirDamper, Outdoor-AirHood Details

Contents

IMPORTANT — READ BEFORE INSTALLING installation, start-upand service instructionsCONTENTS III. Step 3 — Install External Trap forPage Page C. Slab Mount Horizontal Units Only B. Alternate Unit SupportII. STEP 2 — FIELD FABRICATE DUCTWORK IV. STEP 4 — RIG AND PLACE UNITFig. 3 — Roof Curb Details Fig. 5A — Condensate Drain Pan Side View Fig. 4 — Unit Leveling TolerancesFig. 5B — Condensate Drain Piping Details A. PositioningFig. 6 — Rigging Details Page Page —10— —11— VI. STEP 6 — INSTALL GAS PIPING V. STEP 5 — INSTALL FLUE HOODA. Field Power Supply Fig. 8 — Gas Piping Guide With Accessory—13— C. Heat Anticipator Settings—14— —15— Fig. 11 — Field Control Wiring Raceway Fig. 9 — Power Wiring Connections—16— Fig. 10 — Low-VoltageConnectionsOutdoor-AirDamper Installed VIII. STEP 8 — ADJUST FACTORY-INSTALLEDOPTIONSFig. 15 — Outdoor-AirDamper Position Setting A. Manual Outdoor-AirDamperFig. 19 — Indoor Coil Access Panel Relocation Fig. 17 — Typical Access Panel LocationsB. Optional EconoMi$er+ Fig. 16 — EconoMi$er+ Component LocationsFig. 22 — EconoMi$er+ Wiring Fig. 21 — Filter Installation—19— Fig. 20 — Outdoor-AirHood ConstructionE. EconoMi$er+ Controller Wiring C. EconoMi$er+ Control ModeFig. 23 — Barometric Flow Capacity Fig. 24 — Outdoor-AirDamper LeakageG. Outdoor Air Temperature OAT Sensor Provided Table 4 — EconoMi$er+ Field-InstalledAccessoriesH. Supply Air Temperature SAT Sensor Provided J. Return Air Temperature RAT SensorFig. 27 — Return Air Temperature Sensor Fig. 26 — Indoor Air Quality Voltage Setting—22— K. Outdoor Air Humidity Sensor—23— — Thermistor Resolution Temperature Sensors CRTEMPSN001A00 or HH79NZ039Fig. 29 — Enthalpy Changeover Settings Table 6 — Outdoor Air, Return Air, and Supply AirO. Remote EconoMi$er+ Enable Control N. Power ExhaustM. Occupied/Unoccupied Switch Fig. 30 — Humidity Sensor Current vs. Humidity—26— R. CO2 Sensor ConfigurationQ. Demand Ventilation Control Fig. 32 — Demand Ventilation ControlIX. STEP 9 — ADJUST EVAPORATOR-FANSPEED Table 7 — CO2 Sensor* Standard Settings—27— Fig. 33 — Typical Belt-DriveMotor MountingTable 8 — Fan Rpm at Motor Pulley Settings Fig. 35 — Evaporator-FanPulley AdjustmentFig. 34 — Typical Belt-DriveMotor Mounting for SizesGENERAL NOTES FOR FAN PERFORMANCE DATA TABLES —29—Table 10 — Evaporator-FanMotor Performance —30— —31— —32— —33— —34— —35— —36— —37— —38— —39— —40— —41— —42— —43— —44— —45— —46— —47— —48— —49— VII. REFRIGERANT SERVICE PORTS V. INTERNAL WIRINGPRE-START-UP START-UP I. UNIT PREPARATIONX. COOLING A. Adjust Gas InputA. To Shut Off Unit XI. MAIN BURNERSB. Startup Mode XIV. SAFETY RELIEFC. Run Mode D. Read ModeFig. 36 — EconoMi$er+ Controller Board —53—Table 33 — Start-UpMode Sequence —54—Table 32 — EconoMi$er+ Inputs and Outputs Table 35 — Input/Output Channels —55——56— E. Setup Mode—57— F. Manual ModeG. Error Mode —58— —59— C.Demand Ventilation ConfigurationD. Power Exhaust Configuration XVIII. OPERATING SEQUENCE —60—A. Cooling, Units Without EconoMi$er+ B. Heating, Units Without EconoMi$er+I. CLEANING SERVICEFig. 37 — Cleaning Condenser Coil D. Heating, Units With Economizer+IV. BLOWER BELT ADJUSTMENT III.CONDENSER FAN ADJUSTMENT Fig.VI. ECONOMIZER ADJUSTMENT VIII. HIGH-PRESSURESWITCHFig. 41 — Cooling Charging Chart; 580F090 A.To Use Cooling Charging ChartFig. 42 — Cooling Charging Chart; 580F102 —63——64— Fig. 43 — Cooling Charging Chart; 580F120Fig. 44 — Cooling Charging Chart; 580F150 —65— Fig. 45 — Cooling Charging Chart; 580F091—66— Fig. 47 — Cooling Charging Chart; 580F121Fig. 48 — Cooling Charging Chart; 580F151 Table 36 — LED Error Code Description XIV. LIMIT SWITCHXII. FLUE GAS PASSAGEWAYS XIII. COMBUSTION-AIRBLOWERXVII. REPLACEMENT PARTS B.Cleaning and AdjustmentFig. 51 — Spark Gap Adjustment —68—Table 37 — EconoMi$er+ Error Codes TROUBLESHOOTING I. ECONOMI$ER+ TROUBLESHOOTINGA. Error Code 1 — SAT Sensor Failure B. Error Code 2 — RAT Sensor FailureI. Error Mode H. Error Code 8 — E2 Test FailureL. Unit Always In Unoccupied Mode II. UNIT TROUBLESHOOTING—71— Table 39 — Cooling Service Troubleshooting—72— Table 40 — Heating Service Troubleshooting—73— APPENDIX A — ECONOMI$ER+ LABEL —74—APPENDIX A — ECONOMI$ER+ LABEL cont —75——76— INDEX —77—CALL FOR FREE CATALOG SERVICE TRAININGPage START-UPCHECKLIST Remove and Store in Job File TEMPERATURES AND PRESSURESI. PRELIMINARY INFORMATION III.START-UPELECTRICAL