—74—
MODE OF OPERATION |
| PUSHBUTTONS |
|
| LED INDICATORS |
| ||||||
|
|
| Button 1 | Button 2 | DS1 (Red) | DS2 (Yellow) | DS3 (Green) | DS4 (Green) | ||||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |||
STARTUP MODE | Action |
|
| flash |
| flash |
| flash |
| flash | ||
|
|
|
|
|
|
|
|
| ||||
Note 1 | Indicators flash in sequence at .5 sec intervals |
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| |
RUN MODE | Names |
|
| HB | ECONO | Y1 | Y2 | |||||
Actions |
|
| flash | flash | steady | steady | ||||||
|
|
|
| |||||||||
|
|
|
|
|
| |||||||
Note 1 Heartbeat Indicator flashes to indicate proper operation of the control |
|
|
| |||||||||
Note 2 | Econo indicator flashes to indicate free cooling being used |
|
|
|
|
| ||||||
Note 3 | Y1 and Y2 are on steady when a call thermostat Y1 and Y2 are closed |
|
|
| ||||||||
Note 4 | ERROR - HB and Econo are on steady to indicate the presence of an error |
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
| |
|
| Names | READ | ADV | SET NO | I/O NO | TEN'S | ONES OR | ||||
READ MODE | OR ON | OFF | ||||||||||
|
|
|
|
|
|
| ||||||
|
| Actions | Push | Push | flash, no | flash no | flash no | flash no | ||||
|
|
|
|
|
|
|
|
|
|
|
| |
Note 1 Push and release the READ button to enter Read Mode. The SET NO Indicator flashes once to indicate the setup point is selected for viewing
Note 2 Push and release ADV button repeatedly to advance to the desired setup point or I/O point Each time the ADV button is pushed, the SET NO flashes the point number until the desired I/O point is reached and then the I/O NO flashes the I/O point no.
Note 3 After the SET NO indicator identifies the desired point no, push and release the READ button to display the value in the TEN's and ONE's indicator (i.e., 5 flashes for a value of 5) or a steady TEN's indicator for an on and a steady ONE's for off.
To aid in counting, values of 5 are flashed in groups of 5 (i.e., 150 = 3 groups of fast 5 flashes) and then follow by balance in slow flashes (i.e., 7 = 5 quick flashes + 2 slow flashes)
Note 4 Setpoint values are displayed first followed by I/O values and then back to Setpoint values Red Set No LED displays Setup item numbers, and Yellow I/O LED displays I/O item no
Note 5 Routine exits after 10 min of no activity or push and hold button 1 and 2 for 3 seconds to exit
MODE OF OPERATION |
| PUSHBUTTONS |
| LED INDICATORS |
| ||||||
|
|
| Button 1 |
| Button 2 | DS1 (Red) | DS2 (Yellow) |
| DS3 (Green) |
| DS4 (Green) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Names | ADJUST |
| ADV | SET NO | SETUP |
| TEN'S |
| ONES OR |
SETUP MODE |
|
| OR ON |
| OFF | ||||||
|
|
|
|
|
|
|
| ||||
|
| Actions | Hold/Push |
| Push | flash, no | steady |
| flash no |
| flash no |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
| ||||||||
Note 1 Push and hold the ADJUST button until the SETUP indicator turns on. |
|
|
| ||||||||
Note 2 Push and release ADV button repeatedly to advance to the desired setup point. |
| ||||||||||
| Each time the ADV button is pushed, the SET NO flashes the point number and then displays | ||||||||||
| the current setting |
|
|
|
|
|
|
|
|
| |
Note 3 | Once the current value has been displayed the TENS indicator will turn on steady and while it | ||||||||||
| on use the ADJUST button to enter the value. (i.e., push the button 4 times to enter 4) | ||||||||||
| Then wait for the ONES indicator to turn on and enter the ONES setting |
|
|
| |||||||
| Wait for indicator to turn off and then push read/adjust to check the setting |
| |||||||||
Note 4 | Routine exits after 10 min of no activity or push and hold button 1 and 2 for 3 seconds to exit | ||||||||||
|
|
|
|
|
|
|
|
|
|
| |
|
| Names | ADJUST |
| MAN | MAN | I/O NO |
| TEN'S |
| ONES OR |
|
|
|
| OR ON |
| OFF | |||||
| MANUAL |
|
|
|
|
|
|
|
| ||
| Actions | Push | Hold/Push | steady | flash no |
| flash no |
| flash no | ||
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note 1 Push and hold the MAN button until the MAN indicator turns on.
Note 2 Push and release MAN button repeatedly to advance to the desired I/O point. Each time the MAN button is pushed, the I/O NO flashes the I/O point number.
Note 3 After the desired I/O No is reached push and release the ADJUST to toggle the output on and off or open and closed
Note 4 Routine exits after 10 min of no activity or push and hold button 1 and 2 for 3 seconds to exit
APPENDIX A — ECONOMI$ER+ LABEL
I/O POINTS
NO | I/O Points | UNITS |
|
|
|
1 | C1 Output | - |
2 | C2 Output | - |
3 | C3 Output | - |
4 | C4 Output | - |
5 | Economizer Damper Output | % |
6 | Supply Air temperature | F |
7 | Outside Air temperature | F |
8 | Return Air Temperature | F |
9 | Indoor Relative Humidity | % |
10 | Outdoor Relative Humidity | % |
11 | Indoor Air Quality | PPM |
12 | Remote Minimum Position | % |
13 | Y1 Status (next version) | - |
14 | Y2 Status (next version) | - |
15 | G Status (next version) | - |
16 | Occ Status (next version) | - |
ALARM CODES
NO DESCRIPTION
1SAT sensor invalid
2RAT Sensor Invalid (only with changeover type 3&5)
3OAT Sensor Invalid
4ORH Sensor invalid (only with changeover type 3&4)
5IRH Sensor invalid (only with changeover type 5)
6IAQ Sensor Invalid (only if IAQ=1)
7Y2 on Y1 off
8Micro Fails E2 test
note 1 Micro Fails RAM test
note 2 Micro Fails ROM test
Note 1 DS1+DS3/DS2+D4 will alternately flash Note 2 DS1+DS2/DS3+D4 will alternately flash
