Manuals / Cellboost / Lawn and Garden / Utility Vehicle

Cellboost 999-823 General Specifications, Engine System, Hydraulic System, Electrical System

Models: 999-823

1 88

Download 88 pages 11.3 Kb

Page 85

Section 6 – General Specifications

Engine System

Type			Kohler Command Pro
Cooling System			Air Cooled
HP / KW		18 / 13.4
Fuel Tank			3.0 Gallons
Air Cleaner			Standard Air Cleaner
Hydraulic System
Reservoir Capacity			13 gallons
Filter			10 Micron
Electrical System
Battery			12 Volt
Control System
Starting			Keyed ignition switch.
Throttle/Choke			Engine Mounted
Steering	Two spring centered control lever with
Steering		zero turning type controls.
		zero turning type controls.
Warranty
Engine Warranty			Two Year
Product Warranty			One Year
Ground Drive System-Dimensions
Units	English			Metric
Trench Depth	24 - 36		in.	610 - 914		mm
Trench width	4 - 8		in.	101 - 203		mm
Boom travel up			60	Degrees
Boom travel down			61 Degrees
Length (Boom Travel Position)	82		in.	2082.8		mm
Width	35		in.	889		mm
Height	49		in.	1245		mm
Wheel Base	32		in.	813		mm
Ground Speed Forward	200		ft/Min.	61		M/Min.
Ground Speed Reverse	70		ft/Min.	21.3		M/Min.
Chain Speed	280		ft/Min.	7112		M/Min.
Trench center to outside left	15.5		in.	394		mm
Trench center to outside right	19.5		in.	495		mm
Total Weight	1652		lbs	749		kg

6-1

Image 85

Cellboost 999-823 General Specifications, Engine System, Hydraulic System, Electrical System, Control System, Warranty

Contents

COMPACT 118 Operator’s ManualSerial No.s 005 and Higher BIG POWER IN ALL PLACESPOWER WEIGHT118 Operator’s Manual MERTZ MANUFACTURING LLCPage Page WARRANTY AND LIABILITY LIMITATIONS Boxer Product WarrantyCONSEQUENTIAL DAMAGES This warranty is valid only if the following conditions are met TRACK LIMITED PRORATED WARRANTY POLICY STATEMENTThis warranty is subject to the following limitations The following items are not covered by this Track Limited Warranty Please take the time to complete and return this warranty form Boxer Warranty RegistrationFold Affix Stamp Here Mertz Manufacturing, LLC P.O. Box Ponca City, OKBe Prepared - Get to Know All Operating and Safety Instructions Safety IntroductionLearn the Signal Words Used with the Safety Alert Symbol DANGERviii Boxer Product Warranty Table of ContentsTrack Limited Warranty Policy Statement Safety IntroductionConfiguring the Chain SectionTroubleshooting General SpecificationsGENERAL SAFETY Section 1 - Safety PrecautionsSafety Precautions OPERATING SAFETYDO NOT travel ACROSS excessively steep slopes under any circumstances Safety PrecautionsELECTRICAL SYSTEM HAZARDS SERVICE & MAINTENANCE SAFETYSafety Precautions Fuel or oil leaks or spills can create a fire or explosion hazardBattery Hazards Safety PrecautionsJump Starting/Battery Charging Hazards Hydraulic System Hazards Safety PrecautionsSafety Precautions DANGERAlways use a funnel or pour spout when filling the tanks Do not smoke while refueling or when handling the fuel containerSafety Precautions Component Locations Section 2 - Operating ControlsRight Front View DescriptionLeft Rear View Operating ControlsItem No DescriptionOperating Controls Operating ControlsItem No DescriptionOperating Controls Safety DecalsItem No DescriptionOperating Controls Description Operating Controls4. Engine Hour Meter Gauge 5. Hand Grip Operating Controls 9. Keyswitch - Starts and stops the engineSection 3 - Pre-Start Inspection and Operation Daily Service ChecksPre-Start Inspection Table 1 Service Cycle TablePre-Start Inspection and Operation Allow engine to cool before filling fuel tank Pre-Start Inspection and OperationSome examples of common hydraulic hose damage are shown in Figure Pre-Start Inspection and OperationFigure 3-4 Grease Zerk Locations Pre-Start Inspection and OperationBefore starting the engine Pre-Start Inspection and OperationPre-Start Inspection and Operation Operating InstructionsMachine Start-up Machine Shut-down Pre-Start Inspection and OperationTransportation Pre-Start Inspection and Operation Lifting ProceduresPre-Start Inspection and Operation Machine Travel Controls3-10 3-11 Pre-Start Inspection and OperationForward Travel Reverse Travel3-12 Pre-Start Inspection and OperationRight Turn During Forward Travel Right Hand Turn in Forward3-13 Pre-Start Inspection and OperationSpin Turn Figure 3-14 Spin TurnDo not travel up or across a slope steeper than 15. See Figure Pre-Start Inspection and Operation3-14 2437Operating Instructions DO NOT step off of the platform when the chain trencher is engagedPre-Start Inspection and Operation Make sure that you are standing on the operators platform3-16 Pre-Start Inspection and OperationFigure 3-17 Trencher Boom in Raised Position Figure 3-18 Trencher Boom in Raised PositionKeep all workers at least 10 feet from the trenching operation Pre-Start Inspection and Operation3-17 DO NOT travel backwards too fast. The trencher could become unstable Pre-Start Inspection and Operation3-18 Figure 3-21 Trencher at Proper Depththe engine to cool off at idle for 3 - 4 minutes Pre-Start Inspection and Operation3-19 3-20 Pre-Start Inspection and OperationTable 1 Service Cycle Table Section 4 - Routine Service and MaintenanceDaily ActivityRoutine Service and Maintenance Daily Maintenance ProceduresAllow engine to cool before filling fuel tank Routine Service and MaintenanceFigure 4-2 Fuel Level Check Figure 4-3 Air Filter Assembly Routine Service and MaintenanceFigure 4-4 Hydraulic Hose Damage Routine Service and MaintenanceFigure 4-6 Track Adjustment Wrench Storage Routine Service and Maintenance10. Check for proper track tension Figure 4-5 Grease Zerk Locationsh. Shut off the engine and re-measure the deflection dimension Routine Service and MaintenanceRoutine Service and Maintenance New Machine Brake-in Maintenance ProceduresBefore starting the engine Figure 4-8 Engine Oil Filter3. Change the hydraulic filter. See Service Manual and Figure Routine Service and Maintenance4-10 Routine Service and MaintenanceFigure 4-10 Hydraulic Oil Check and Fill 2449Routine Service and Maintenance Weekly Maintenance Procedures4-11 Routine Service and Maintenance Monthly Maintenance ProceduresFigure 4-12 Air Filter Assembly 4-12DANGER Routine Service and Maintenance4. Replace fuel filter 4-137. The electrical system on this machine is a NEGATIVE ground system Routine Service and Maintenance4-14 If the battery needs to be replaced, make sure to dispose of the Routine Service and Maintenance4-15 Routine Service and Maintenance Annual Maintenance Procedures4-16 d. Replace hydraulic filter. See page 4-9, Step Routine Service and Maintenance4-17 Routine Service and Maintenance General MaintenanceDANGER Draining Fuel TankSpilled fuel may be ignited by a hot engine Routine Service and Maintenance4-19 Adjusting Digging Chain Tension Routine Service and Maintenance4-20 1 3/4 - 2”If the chain tension needs to be adjusted Routine Service and Maintenance4-21 Trencher Boom Replacement Routine Service and Maintenance4-22 10. Reinstall the boom guard Item 1, Figure Routine Service and MaintenanceFigure 4-20 Trencher Boom Assembly 4-23Replacing the Digging Teeth Routine Service and Maintenance4-24 Replacing the Drive Sprocket Routine Service and Maintenance4-25 4-26 Routine Service and MaintenanceFigure 4-22 Replacing Drive Sprocket Routine Service and Maintenance RearChain Configuration 4-27Chain Master Link Routine Service and Maintenance4-28 Configuring the Chain Routine Service and Maintenance4-29 Trencher Chain Parts list Parts ListRoutine Service and Maintenance 4-30Configuration A Routine Service and MaintenanceConfiguration D Configuration BRoutine Service and Maintenance Boxer 118 Hydraulic Interconnect DiagramFigure 4-26 Boxer 118 Hydraulic Interconnect Diagram 4-32Problem Section 5 - TroubleshootingPossible Causes Corrective ActionProblem TroubleshootingPossible Causes Corrective ActionProblem TroubleshootingPossible Causes Corrective ActionTroubleshooting Warranty Section 6 - General SpecificationsGround Drive System-Dimensions Engine SystemGeneral Specifications Noise DataDOTTED DO NOT REMOVE THIS PAGE FROM THE MANUALDEGREE SLOPEPhone 800-476-9673 - Fax Compact Power Inc P.O. Box 40 - Fort Mill, SCPart Number