Table- or Shelf-Mounting | Cisco Systems 3650 specs

Chapter 2 Switch Installation

Installing the Switch

Table- or Shelf-Mounting

To install the switch on a table or shelf, locate the adhesive strip with the rubber feet in the mounting-kit envelope. Attach the four rubber feet to the recessed areas on the bottom of the chassis (see Figure 2-10).

Figure 2-10 Attaching the Adhesive Pads for Table- or Shelf-Mounting

PWR-C2-640WAC

PWR-C2-640WAC

CONSOLE

MGMT

1	3
	47793
	1

1

Adhesive pads

When you complete the switch installation, see the “After Installing the Switch” section on page 2-14for more information about the switch configuration.

After Installing the Switch

After the switch is installed, you might need to:

•Configure the switch by running Express Setup to enter the initial switch configuration. For instructions, see the switch getting started guide that shipped with the switch and also on Cisco.com.

•Use the CLI setup program to enter the initial switch configuration. See Appendix C, “Configuring the Switch with the CLI-Based Setup Program.”

•Connect to the front-panel ports. See the “Connecting Devices to the Ethernet Ports” section on page 2-19.

	Catalyst 3650 Switch Hardware Installation Guide
2-14	OL-29734-01

Image 38

Cisco Systems 3650 manual Table- or Shelf-Mounting, After Installing the Switch

Contents

Document Conventions PrefacePurpose Obtaining Documentation and Submitting a Service Request Related Documentation Product Overview Switch ModelsSwitch Model Cisco IOS Image Description Product Overview Switch Models Switch Model Cisco IOS Image Description Front Panel Catalyst 3650-48PD-L Switch Front Panel Management Ports 10/100/1000 Ethernet PortsPoE and PoE+ USB Type a Port USB Mini-Type B Port SFP and SFP+ Modules Uplink PortsLEDs 3 4 5 Color System Status Mode LED Port Mode Description Port LEDs and Modes Port Mode Port LED Color Meaning USB Console LED Color PoE+ LED Color Description Uplink Ports LEDs Color PoE+ Status Rear Panel Color Uplink Ports Link Status RJ-45 Console Port Status1 RJ-45 Console Port LEDStackWise Ports Power Supply Modules AC-Power Supply Module LEDs Models Default Power Supply Available PoE PowerPoE Option Port Switch Models DC-Power Supply Module LEDs Fan Modules RJ-45 Console Port Management OptionsEthernet Management Port Network Configurations OL-29734-01 Safety Warnings Switch InstallationPreparing for Installation OL-29734-01 Installation Guidelines Powering Off the Switch Planning a Switch Data StackVerifying Switch Operation Tools and Equipment Switch Stacking Guidelines Data Stack Cabling Configurations Data Stacking up to Four Switches in a Side-by-Side Mounting Data Stack Bandwidth and Partitioning Examples Power-On Sequence for Switch Data Stacks Example of a Data Stack with Half Bandwidth Connections Changes to Switch Stack Membership Installing the Switch Rack-Mounting Attaching the Rack-Mount Brackets Rack-Mounting Brackets Attaching Brackets for 19-inch Racks Mounting the Switch in a Rack Mounting the Switch in a Rack After Installing the Switch Table- or Shelf-Mounting Connecting to the StackWise Ports Installing the StackWise Adapter in a StackWise Port Installing and Removing SFP and SFP+ Modules Installing SFP and SFP+ Modules 14 Installing an SFP Module in an Uplink Port 10/100/1000 Ethernet Port Connections Connecting Devices to the Ethernet PortsRemoving SFP or SFP+ Modules Switch Installation Connecting Devices to the Ethernet Ports PoE+ Port Connections Device Crossover Cable Where to Go Next Part Number Description Power Supply InstallationPower Supply Module Overview AC OK LED 640-W AC Power Supply Module 6 5 DC Power Supply Module LEDs Installation GuidelinesAC Power Supply Module LEDs Installing or Replacing an AC Power Supply Installing a DC Power Supply Statement Grounding the Switch Equipment That You Need Stripping the Ground Wire 10 Attaching the Ground Lug and Wire Assembly Installing the DC Power Supply in the Switch Wiring the DC Input Power Source Finding the Power Supply Module Serial Number 12 DC Source a Isolated From Source B with No Common Ground 14 1025-W AC Power Supply Serial Number 16 640-W DC Power Supply Module Serial Number Installing the Fan Overview Fan Module Installation Installing a Fan Module Fan LED Finding the Fan Module Serial Number Fan Module Serial Number Switch Post Results TroubleshootingDiagnosing Problems Switch LEDs Ethernet and Fiber Cables Switch ConnectionsBad or Damaged Cable Link Status SFP Modules 10/100/1000 Port ConnectionsPoE and PoE+ Port Connections Ping End Device Switch PerformanceInterface Settings Spanning Tree Loops Cabling Distance Resetting the SwitchAutonegotiation and Network Interface Cards Finding the Switch Serial Number Replacing a Failed Data Stack Member Environmental Ranges Technical SpecificationsSwitch Specifications Physical Specifications Power Supply Module Specifications Power Specifications Power Specifications Operating Specification Fan Module SpecificationsPhysical Specification OL-29734-01 10/100/1000 Ports Connector and Cable SpecificationsConnector Specifications Gigabit Ethernet CX1 SFP+ Copper Connectors SFP and SFP+ Modules Figure B-4 Simplex LC Cable Connector 10/100/1000 Ethernet Management Port Console Port Figure B-7 10/100 Port Pinouts Cable and Adapter Specifications StackWise Cables Locating the StackWise Adapter Serial Number StackWise AdaptersStackWise Cables Minimum Bend Radius and Coiled Diameter Cable Part Number Cable Length Minimum Bend Radius SFP and SFP+ Module Cable Specifications StackWise Adapter Blanks Four Twisted-Pair Cable Pinouts Two Twisted-Pair Cable Pinouts Console Port Adapter Pinouts Switch Console RJ-45-to-DB-9 Port DTEIdentifying a Crossover Cable Device Switch Console RJ-45-to-DB-25 Port DTE DSR DTR CTS RTS Accessing the CLI Through Express Setup Configuring the Switch with the CLI-Based Setup ProgramAccessing the CLI Accessing the CLI Through a Console Port USB Console Port Installing the Cisco Microsoft Windows USB Device Driver Uninstalling the Cisco Microsoft Windows USB Driver Uninstalling the Cisco Microsoft Windows XP USB Driver Configuring the Setup Program Entering the Initial Configuration InformationIP Settings Enter a host name for the switch, and press Return These choices appear OL-29734-01