Cisco Systems 3650 Installing a Fan Module

4-3

Catalyst 3650 Switch Hardware Installation Guide

OL-29734-01

Chapter4 Installing the Fan

Fan Module Installation

Installing a Fan Module

Step1 Pinch the fan module release handle, and slide the module out.

Caution You should replace the fan module within 5minutes to avoid overheating the switch.

Step2 Install the fan module in the fan slot, and firmly push it into the slot, applying pressure to the end of the

module, not the extraction handles. When correctly inserted, the fan module is flush with the switch rear

panel. When the fan is operating, a green LED is on in the top left corner of the fan. See Figure 4-2.

Warning

Do not reach into a vacant slot when installing or removing a module. Exposed circuitry is an energy

hazard.

Statement 206

Figure4-2 Installing the Fan Module

1Fan LED

347794

PWR-C2-640WAC PWR-C2-640WDC

CONSOLE MGMT

Contents

Main Preface Purpose Document Conventions Related Documentation Obtaining Documentation and Submitting a Service Request Product Overview Switch Models Page Page Front Panel Page 10/100/1000 Ethernet Ports PoE and PoE+ Management Ports USB Mini-Type B Port USB Type A Port Uplink Ports SFP and SFP+ Modules LEDs SYST LED 01X Port LEDs and Modes Page USB Console LED ACTV LED STACK LED PoE+ LED Uplink Ports LEDs Rear Panel RJ-45 Console Port LED StackWise Ports 1 2 744 85 5 6 76 8 3 4 Power Supply Modules Page Fan Modules Management Ports Ethernet Management Port RJ-45 Console Port Management Options Network Configurations Page Switch Installation Preparing for Installation Safety Warnings 2-2 Installation Guidelines Tools and Equipment Verifying Switch Operation Powering Off the Switch Planning a Switch Data Stack Switch Stacking Guidelines Data Stack Cabling Configurations Data Stack Bandwidth and Partitioning Examples Power-On Sequence for Switch Data Stacks Changes to Switch Stack Membership Installing the Switch Rack-Mounting Attaching the Rack-Mount Brackets 3 4 5 Page Mounting the Switch in a Rack Table- or Shelf-Mounting After Installing the Switch Connecting to the StackWise Ports Page Installing and Removing SFP and SFP+ Modules Installing SFP and SFP+ Modules Page Removing SFP or SFP+ Modules Connecting Devices to the Ethernet Ports 10/100/1000 Ethernet Port Connections Page PoE+ Port Connections Where to Go Next Power Supply Installation Power Supply Module Overview 3 5 6 Page Page Installation Guidelines Installing or Replacing an AC Power Supply Installing a DC Power Supply Equipment That You Need Grounding the Switch Page Page Installing the DC Power Supply in the Switch Wiring the DC Input Power Source Finding the Power Supply Module Serial Number 3-13 Page Installing the Fan Overview Fan Module Installation Installation Guidelines Installing a Fan Module Finding the Fan Module Serial Number Troubleshooting Diagnosing Problems Switch POST Results Switch LEDs Switch Connections Bad or Damaged Cable Ethernet and Fiber Cables Link Status 10/100/1000 Port Connections PoE and PoE+ Port Connections SFP Modules Interface Settings Ping End Device Switch Performance Speed, Duplex, and Autonegotiation Autonegotiation and Network Interface Cards Cabling Distance Resetting the Switch Finding the Switch Serial Number Replacing a Failed Data Stack Member A Technical Specifications Switch Specifications Page Power Supply Module Specifications Page Fan Module Specifications Page B Connector and Cable Specifications Connector Specifications 10/100/1000 Ports 10-Gigabit Ethernet CX1 (SFP+ Copper) Connectors SFP and SFP+ Modules B-3 FigureB-4 Simplex LC Cable Connector FigureB-5 Copper SFP Module RJ-45 Connector 10/100/1000 Ethernet Management Port 23145678Pin Label Console Port Cable and Adapter Specifications StackWise Cables StackWise Cables Minimum Bend Radius and Coiled Diameter StackWise Adapters Locating the StackWise Adapter Serial Number StackWise Adapter Blanks SFP and SFP+ Module Cable Specifications B-8 Four Twisted-Pair Cable Pinouts Two Twisted-Pair Cable Pinouts Identifying a Crossover Cable Console Port Adapter Pinouts Page C Configuring the Switch with the CLI-Based Setup Program Accessing the CLI Accessing the CLI Through Express Setup Accessing the CLI Through a Console Port RJ-45 Console Port USB Console Port Installing the Cisco Microsoft Windows USB Device Driver Uninstalling the Cisco Microsoft Windows USB Driver Uninstalling the Cisco Microsoft Windows USB Driver Using the Add or Remove Programs Utility Uninstalling the Cisco Microsoft Windows XP USB Driver Uninstalling the Cisco Microsoft Windows Vista and 7 USB Driver Uninstalling the Cisco Microsoft Windows USB Driver Using the Setup.exe Program Entering the Initial Configuration Information IP Settings Configuring the Setup Program