Appendix C Configuring the Switch with the CLI-Based Setup Program

Entering the Initial Configuration Information

 

 

 

 

At any point you may enter a question mark '?' for help.

 

 

 

 

Use ctrl-c to abort configuration dialog at any prompt.

 

 

 

 

Default settings are in square brackets '[]'.

 

 

 

 

Basic management setup configures only enough connectivity

 

 

 

 

for management of the system, extended setup will ask you

 

 

 

 

to configure each interface on the system.

 

 

 

 

Would you like to enter basic management setup? [yes/no]: yes

 

 

 

Step 2

Enter a host name for the switch, and press Return.

 

 

 

 

On a command switch, the host name is limited to 28 characters and on a member switch to 31

 

 

 

 

characters. Do not use -n, where n is a number, as the last character in a host name for any switch.

 

 

 

 

Enter host name [Switch]: host_name

 

 

 

Step 3

Enter an enable secret password, and press Return.

 

 

 

 

The password can be from 1 to 25 alphanumeric characters, can start with a number, is case sensitive,

 

 

 

 

allows spaces, but ignores leading spaces. The secret password is encrypted, and the enable password is

 

 

 

 

in plain text.

 

 

 

 

Enter enable secret: secret_password

 

 

 

Step 4

Enter an enable password, and press Return.

 

 

 

 

Enter enable password: enable_password

 

 

 

Step 5

Enter a virtual terminal (Telnet) password, and press Return.

 

 

 

 

The password can be from 1 to 25 alphanumeric characters, is case sensitive, allows spaces, but ignores

 

 

 

 

leading spaces.

 

 

 

 

Enter virtual terminal password: terminal-password

 

 

 

Step 6

To configure the country code, enter yes and press Return.

 

 

 

 

Do you want to configure country code? [no]: yes

 

 

 

Step 7

Enter the country code, and press Return.

 

 

 

 

Enter the country code[US]:US

 

 

 

Step 8

(Optional) Configure Simple Network Management Protocol (SNMP) by responding to the prompts. You

 

 

 

 

can also configure SNMP later through the CLI, Device Manager, or the Cisco Network Assistant

 

 

 

 

application. To configure SNMP later, enter no.

 

 

 

 

Configure SNMP Network Management? [no]: no

 

 

 

Step 9

Enter the interface name (physical interface or VLAN name) of the interface that connects to the

 

 

 

 

management network, and press Return. For this release, always use vlan1 as that interface.

 

 

 

 

Enter interface name used to connect to the

 

 

 

 

management network from the above interface summary: vlan1

 

 

 

Step 10 Configure the interface by entering the switch IP address and subnet mask and pressing Return. The IP

 

 

 

 

address and subnet masks shown are examples.

 

 

 

 

Configuring interface vlan1:

 

 

 

 

Configure IP on this interface? [yes]: yes

 

 

 

 

IP address for this interface: 10.4.120.106

 

 

 

 

Subnet mask for this interface [255.0.0.0]: 255.0.0.0

 

 

 

Catalyst 3650 Switch Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

C-6

 

 

OL-29734-01

 

 

 

 

 

Page 92
Image 92
Cisco Systems 3650 manual Enter a host name for the switch, and press Return