Manuals
/
Cisco Systems
/
Computer Equipment
/
Network Router
Cisco Systems
7507 quick start
Models:
7507
1
2
44
44
Download
44 pages
1.1 Kb
1
2
3
4
5
6
7
8
<
>
Install
Configure IP? yes yes Configure IGRP routing? yes yes
Perform a Basic Configuration Using Setup
the copy running-config startup-config command
For DC-Input Power Supply
Enable Booting from Flash Memory
Perform a Basic Configuration Using Configuration Mode
Page 2
Image 2
Page 1
Page 3
Page 2
Image 2
Page 1
Page 3
Contents
INSTALL FIELD REPLACEABLE UNITS FRUS
INSTALL THE HARDWARE
START AND CONFIGURE THE SYSTEM
Quick Start Guide
Page
Install the Hardware
Packing List
For rack-mounting optional
Prepare to Install the Router
For DC-Input Power Supply
For interface modules optional
Install the Router
Install the Hardware
Bracket
Rack-Mount the Router Optional
Install the Hardware
ears to chassis
Mount Brackets to the Rack Posts
Install the Hardware
Install the Hardware
Secure the Spacers
Step
Step
Attach the Chassis Ears
Install the Hardware
Step
Mount the Chassis in the Rack
Install the Hardware
Step
Step
Remove the Chassis Foot
Install the Hardware
Step
Install Interface Processors, Fillers, VIPs, or RSPs
Install the Hardware
Install Power Supplies in the Router
Install the Hardware
Page
Captive installation screws
Install the DC-Input Power Supply
Install the Hardware
on terminal block cover
Step 2 Lift and remove the terminal block cover
Connect the Auxiliary Port
Connect the RSP
Connect the Console Port
Connect the Console and the Auxiliary Y-Cables
Connect the RSP
Start and Configure the System
running-config startup-config command
Configure Using AutoInstall
the copy running-config startup-config command
Start a Basic Configuration
Perform a Basic Configuration Using Setup
Start and Configure the System
Your IGRP autonomous system number 1
running-config startup-config command
Configure IP? yes yes Configure IGRP routing? yes yes
Start and Configure the System
running-config startup-config command
Configuring interface Serial1/0 Is this interface in use? no yes
Configure an Ethernet Interface
NVRAM as follows
Start and Configure the System
Perform a Basic Configuration Using Configuration Mode
running-config startup-config command
Step 2 Enter the interface type slot/port
57002
Install Field Replaceable Units FRUs
Flash Memory Cards
SLOTSLOT
The label should face right
Copy Files to Flash Memory
Use the command copy tftpfilename bootflash
Format a Flash Memory Card
Install Field Replaceable Units FRUs
Step 3 Enter the boot system flash
Make a Flash Memory Card Image Bootable
Enable Booting from Flash Memory
Step 4 Enter the boot system flash bootflashslot0 filename command, as
Prepare to Remove and Install an RSP
Install Field Replaceable Units FRUs
Captive guide installation screw B C
Remove and Install an Interface Processor, Filler, VIP, or RSP
Install Field Replaceable Units FRUs
Bottom ejector lever A Card Card carrier slot
Check the RSP Installation
Install Field Replaceable Units FRUs
Check the Interface Processor or VIP Installation
Install Field Replaceable Units FRUs
Install Field Replaceable Units FRUs
Copy the Configuration File for an RSP
Step Step Step
Remote host ? servername
Router# copy startup-config tftp
server is servername
Translating servername...domain server 1.1.1.1 OK
Install Field Replaceable Units FRUs
The system displays a series of exclamation points
Router# copy tftp startup-config
Retrieve the Configuration File for RSPs
Install Field Replaceable Units FRUs
10.1.1.1
systemrunning-config nvramstartup-config command
Install Field Replaceable Units FRUs
Screw
Remove and Install Port Adapters
Install Field Replaceable Units FRUs
Carrier
See C
Remove and Replace the Power Supply
Install Field Replaceable Units FRUs
Install Field Replaceable Units FRUs
Step 7 Pull the power supply out of the bay and put it aside
Americas
Corporate Headquarters
European Headquarters
Asia Pacific Headquarters