Manuals
/
Cisco Systems
/
Computer Equipment
/
Network Router
Cisco Systems
7507 quick start
Models:
7507
1
44
44
Download
44 pages
1.1 Kb
37
38
39
40
41
42
43
44
<
>
Install
Configure IP? yes yes Configure IGRP routing? yes yes
Perform a Basic Configuration Using Setup
the copy running-config startup-config command
For DC-Input Power Supply
Enable Booting from Flash Memory
Perform a Basic Configuration Using Configuration Mode
Page 44
Image 44
42
Page 43
Page 44
Image 44
Page 43
Contents
INSTALL THE HARDWARE
START AND CONFIGURE THE SYSTEM
INSTALL FIELD REPLACEABLE UNITS FRUS
Quick Start Guide
Page
Install the Hardware
Packing List
Prepare to Install the Router
For DC-Input Power Supply
For rack-mounting optional
For interface modules optional
Install the Router
Install the Hardware
Rack-Mount the Router Optional
Install the Hardware
Bracket
ears to chassis
Mount Brackets to the Rack Posts
Install the Hardware
Secure the Spacers
Step
Install the Hardware
Step
Attach the Chassis Ears
Install the Hardware
Mount the Chassis in the Rack
Install the Hardware
Step
Step
Remove the Chassis Foot
Install the Hardware
Step
Step
Install Interface Processors, Fillers, VIPs, or RSPs
Install the Hardware
Install Power Supplies in the Router
Install the Hardware
Page
Install the DC-Input Power Supply
Install the Hardware
Captive installation screws
on terminal block cover
Step 2 Lift and remove the terminal block cover
Connect the Auxiliary Port
Connect the RSP
Connect the Console Port
Connect the Console and the Auxiliary Y-Cables
Connect the RSP
Start and Configure the System
Configure Using AutoInstall
the copy running-config startup-config command
running-config startup-config command
Start a Basic Configuration
Perform a Basic Configuration Using Setup
Start and Configure the System
Your IGRP autonomous system number 1
running-config startup-config command
Configure IP? yes yes Configure IGRP routing? yes yes
running-config startup-config command
Configuring interface Serial1/0 Is this interface in use? no yes
Start and Configure the System
Configure an Ethernet Interface
NVRAM as follows
Perform a Basic Configuration Using Configuration Mode
running-config startup-config command
Start and Configure the System
Step 2 Enter the interface type slot/port
Install Field Replaceable Units FRUs
Flash Memory Cards
57002
SLOTSLOT
The label should face right
Use the command copy tftpfilename bootflash
Format a Flash Memory Card
Copy Files to Flash Memory
Install Field Replaceable Units FRUs
Make a Flash Memory Card Image Bootable
Enable Booting from Flash Memory
Step 3 Enter the boot system flash
Step 4 Enter the boot system flash bootflashslot0 filename command, as
Prepare to Remove and Install an RSP
Install Field Replaceable Units FRUs
Remove and Install an Interface Processor, Filler, VIP, or RSP
Install Field Replaceable Units FRUs
Captive guide installation screw B C
Bottom ejector lever A Card Card carrier slot
Check the RSP Installation
Install Field Replaceable Units FRUs
Check the Interface Processor or VIP Installation
Install Field Replaceable Units FRUs
Install Field Replaceable Units FRUs
Copy the Configuration File for an RSP
Step Step Step
Router# copy startup-config tftp
server is servername
Remote host ? servername
Translating servername...domain server 1.1.1.1 OK
Install Field Replaceable Units FRUs
The system displays a series of exclamation points
Retrieve the Configuration File for RSPs
Install Field Replaceable Units FRUs
Router# copy tftp startup-config
10.1.1.1
systemrunning-config nvramstartup-config command
Install Field Replaceable Units FRUs
Remove and Install Port Adapters
Install Field Replaceable Units FRUs
Screw
Carrier
See C
Remove and Replace the Power Supply
Install Field Replaceable Units FRUs
Install Field Replaceable Units FRUs
Step 7 Pull the power supply out of the bay and put it aside
Corporate Headquarters
European Headquarters
Americas
Asia Pacific Headquarters