Manuals / Cisco Systems / Computer Equipment / Network Router

Cisco Systems ASR 903 manual Interface Module LEDs, RSP LEDs continued

Models: ASR 903

1 118

Download 118 pages 26.92 Kb

Page 110

RSP LEDs (continued)

Chapter 5 Troubleshooting

LED Summary

Table 5-10	RSP LEDs (continued)

LED	Color/State	Description (two LEDs for eachT1/E1 port)

	Flashing	Holdover
	yellow

	Green	Locked to source

USB flash	Flashing	USB activity
(MEM)	green

BITS	Off	Out of service/not configured

	Amber	Fault or loop condition

	Green	In frame/working properly

Interface Module LEDs

Table 5-11summarizes the interface module LEDs. This LED summary applies to the following interface modules:

•SFP Gigabit Ethernet Interface Module

•RJ45 Gigabit Ethernet Interface Module

•XFP 10 Gigabit Ethernet XFP Interface Module

	Table 5-11	Interface Module LEDs

	LED	Color/State	Description

	Power	Off	Disabled/no power to IM
	(PWR)
	(PWR)	Green	Enabled and power rails on IM in range
		Green	Enabled and power rails on IM in range

	Status	Off	Disabled/power-down
	(STAT)
	(STAT)	Red	Failure (on at reset)
		Red	Failure (on at reset)

		Amber	Booting (if local CPU)

		Green	Operational

	Link status	Off	Inactive or no connection
	(L)
	(L)	Amber	Fault/loop condition
		Amber	Fault/loop condition

		Green	Ok with no activity

		Flashing	OK with activity
		green

	Speed (S)	Off	100/10 Mbps/Slow

		Green	1Gbps/Full

Cisco ASR 903 Router Hardware Installation Guide

5-8	OL-25178-04

Image 110

Cisco Systems ASR 903 manual Interface Module LEDs, RSP LEDs continued

Contents

Cisco ASR 903 Router Hardware Installation Guide Cisco Systems, IncJune Text Part Number OL-25178-04THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS RSP Modules Obtaining Documentation and Submitting a Service RequestC O N T E N T S Dying GaspPreparing for Installation Safety GuidelinesInstalling the Chassis Brackets Precautions for Rack-MountingInstalling the Fan Tray RSP InstallationInstalling the Cisco Microsoft Windows USB Device Driver Installing an Interface ModuleUsing the Console Interface Connecting Ethernet CablesVerifying the Hardware Configuration TroubleshootingSite Log A-1 Alarm ConditionsFan Tray LEDs ContentsOL-25178-04 viiiContents Cisco ASR 903 Router Hardware Installation Guide Document Revision History Obtaining Documentation and Submitting a Service Request, pageAbout this Book Document AudienceInitial Configuration” Installation”Chapter 3, “Installing the Cisco ASR Chapter 5, “Troubleshooting”Obtaining Documentation and Submitting a Service Request Tip Means the following information will help you solve a problemChapter Cisco ASR 903 Router Hardware Installation Guide OL-25178-04C H A P T E R Cisco ASR 903 Router FeaturesCisco ASR 903 Router Overview System Specifications Interface modulesRedundancy, page Dying Gasp, page Status LEDs, page Power Supply FeaturesDC Power Specifications, page Redundancy DC Power SpecificationsAC Power Specifications, page Dying GaspAC Power Specifications Fan TrayNetwork Timing Interfaces, page RSP Interfaces, page Supported RSP Features, page RSP Redundancy, pageRSP Modules RSP Redundancy Supported RSP FeaturesSupported RSPs Label Network Timing InterfacesRSP Interfaces InterfaceSupported SFP Modules Interface ModulesGigabit Ethernet SFP Interface Module Gigabit Ethernet SFP Interface Module, pageGigabit Ethernet RJ45 Interface Module 1-10Supported SFP Modules 10 Gigabit Ethernet XFP Interface Module1-11 1-12 DWDM-XFP-46.92 DWDM-XFP-47.72 DWDM-XFP-48.51 DWDM-XFP-50.12Figure 1-7 16 x T1/E1 Interface Module T1/E1 Interface Module1-13 Supported SFP Modules OC-3 Interface Module1-14 Serial Number Label Location Temperature SensorInterface Numbering 1-15Information for the Cisco ASR 903 Router document Regulatory Compliance1-16 Safety Guidelines, page Site Planning, page Preparing for InstallationSafety Guidelines Safety Guidelines for Personal Safety and Equipment Protection, pageStandard Warning Statements Safety Guidelines for Personal Safety and Equipment Protection Safety Precautions for Module Installation and RemovalSafety with Electricity Warning Use copper conductors only. Statement Warning Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement Page Power Supply Considerations Preventing ESD DamageGeneral Precautions, page Site Planning Checklist, page General PrecautionsSite Planning Checklist Floor Loading Considerations, page Site Power Guidelines, pageEnvironmental Requirements Physical CharacteristicsSite Selection Guidelines 2-10Air exhaust Air Flow Guidelines2-11 Room airFloor Loading Considerations Site Power GuidelinesAir Flow Guidelines for Enclosed Rack Installation 2-122-13 Site Cabling GuidelinesElectrical Circuit Requirements Electromagnetic Interference Asynchronous Terminal ConnectionsInterference Considerations Radio Frequency InterferencePrecautions for Rack-Mounting, page Rack Selection Guidelines, page Precautions for Rack-MountingLightning and AC Power Fault Interference Rack-Mounting GuidelinesEquipment Rack Guidelines Locating for SafetyLocating for Easy Maintenance 2-16Locating for Proper Airflow 2-17Installation Checklist 2-182-19 Receiving the Cisco ASR 903 RouterCreating a Site Log 2-20 Chassis-Lifting GuidelinesTools and Equipment 2-21 Unpacking and Verifying the Shipped ContentsStatement 2-22 Accessories kitPrerequisites, page Installing the Router in a Rack, page Installing the Cisco ASR 903 RouterInstalling the Router in a Rack Installing the Chassis Ground Connection, pageInstalling the Chassis Brackets Installing the Router Chassis in the Rack Figure 3-6 Cable Management Bracket Installation Attaching the Cable Management BracketsFigure 3-5 Installing the Chassis in a 300 mm ETSI Cabinet Installing the Chassis Ground Connection 0.5 in. 12.7 mm ± 0.02 in. 0.5 mm Figure 3-9 Stripping a Ground WireWire lead InsulationFigure 3-10 Crimping a Ground Lug onto the Ground Wire Installing the Fan Tray Removing and Replacing the Fan TrayHandle Captive installation screwFigure 3-12 Detaching the Fan Tray Hot-Swapping an RSP Module, page RSP InstallationInstalling an RSP Module, page Removing an RSP Module, page 3-10Installing an RSP Module 3-11Removing an RSP Module 3-12Hot-Swapping an RSP Module 3-13Installing an Interface Module, page Interface Module InstallationInstalling an Interface Module Removing an Interface Module, page3-15 Removing an Interface ModuleHot-Swapping an Interface Module 3-16 Caution To avoid erroneous failure messages, note the current configuration of all interfaces before you remove or replace an interface module, and allow at least 2 minutes for the system to reinitialize after a module has been removed or replaced. This time is recommended in order to allow for synchronization between components within the interface module and for synchronization with the standby RSPPreventing Power Loss, page Power Connection Guidelines, page Installing the Power SupplyPreventing Power Loss Installing the DC Power Supply, pageGuidelines for AC-Powered Systems Power Connection GuidelinesGuidelines for DC-Powered Systems 3-18Installing the DC Power Supply Module, page Installing the DC Power SupplyInstalling the DC Power Supply Module Installing the Terminal Block, pageInstalling the Terminal Block 3-203-21 Ground lead wire3-22 Torque is from 4.425 in.-lb .5 N-m to 5.310 in-lb .6 N-mActivating the DC Power Supply 3-23Statement Removing and Replacing the DC Power Supply3-24 StatementInstalling the AC Power Supply Module, page Installing the AC power SupplyInstalling the AC Power Supply Module Activating the AC Power Supply, page3-26 Removing and Replacing the AC Power SupplyActivating the AC Power Supply Connecting Console Cables, page Connecting the Cisco ASR 903 Router to the NetworkConnecting Console Cables Connecting to the Auxiliary Port, pageConnecting to the Serial Port using Microsoft Windows 3-28Connecting the Cisco ASR 903 Router to the Network 3-29Chapter 3 Installing the Cisco ASR 903 Router Cisco ASR 903 Router Hardware Installation GuideStep 1 Use the Finder to go to Applications Utilities Terminal Connecting to the Console Port using Mac OSConnecting to the Console Port using Linux 3-30Installing the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows USB Device DriverInstalling the Cisco Microsoft Windows XP USB Driver “Installing the Cisco Microsoft Windows XP USB Driver”Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver Uninstalling the Cisco Microsoft Windows USB DriverInstalling the Cisco Microsoft Windows Vista USB Driver “Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver”3-33 Connecting to the Auxiliary PortUninstalling the Cisco Microsoft Windows Vista USB Driver 3-34 To connect a modem to the router, follow these stepsConnecting a USB Flash Device Connecting a Management Ethernet CableInstalling and Removing SFP and XFP Modules 3-35Connecting Cables to the BITS Interface, page Connecting Timing CablesConnecting Cables to the BITS Interface Connecting Cables to a GPS Interface, page3-37 Step 4 Turn on power to the routerConnecting Cables to the Output 10Mhz or 1PPS Interface Connecting Cables to a GPS InterfaceConnecting Cables to the Input 10Mhz or 1PPS Interface Connecting Cables to the ToD InterfaceConnecting Ethernet Cables 3-39Installing the Cable Connector Connecting Cables to SFP ModulesConnecting T1/E1 cables 3-40For the T1/E1 ports, see the “T1/E1 Port Pinout” section on page Connecting Cables to the Patch PanelRJ45 Cable Pinouts 3-413-42 Connecting the Fan Tray Alarm PortRecommended Patch Panel Chapter 3 Installing the Cisco ASR 903 Router Connector and Cable Specifications3-43 Connecting the Cisco ASR 903 Router to the NetworkConnecting the Cisco ASR 903 Router to the Network 3-44Chapter 3 Installing the Cisco ASR 903 Router Cisco ASR 903 Router Hardware Installation GuideConfiguring the Cisco ASR 903 Router at Startup, page Cisco ASR 903 Router Initial ConfigurationPowering Up the Cisco ASR 903 Router, page Safely Powering Off the Cisco ASR 903 Router, pagePowering Up the Cisco ASR 903 Router Example 4-1 Loading the Default System Boot ImageCisco ASR 903 Router Hardware Installation Guide Chapter 4 Cisco ASR 903 Router Initial ConfigurationPowering Up the Cisco ASR 903 Router initrd at 009B9000 isord at 01007000 0D1DF800 avail ram 00400000Cisco ASR 903 Router Hardware Installation Guide Chapter 4 Cisco ASR 903 Router Initial ConfigurationPowering Up the Cisco ASR 903 Router Verifying the Front Panel LEDs Configuring the Cisco ASR 903 Router at StartupVerifying the Hardware Configuration Checking Hardware and Software CompatibilityUsing the Console Interface Configuring Global ParametersRouter# show running-config Checking the Running Configuration SettingsSaving the Running Configuration to NVRAM Safely Powering Off the Cisco ASR 903 Router USB Console Port Pinout, page Fiber-Optic Specifications, page TroubleshootingTime of Day Port Pinout, page Alarm Port Pinout, page PinoutsBITS Port Pinout continued GPS Port PinoutTime of Day Port Pinout GPS Port PinoutExternal Alarm Input Pinout Alarm Port PinoutConsole/Aux RJ45 RS232 Serial Port Pinout RJ45 1PPS/ToD Port Pinout continuedT1/E1 Port Pinout T1/E1 Interface PinoutsT1/E1 Interface Pinouts continued Management Ethernet Port PinoutFan Tray Alarm Port Pinout USB Flash/MEM Port Pinout Fiber-Optic SpecificationsUSB Console Port Pinout Single USB Console PortLED Summary RSP LEDs, page Interface Module LEDs, page Power Supply LEDs, pageFan Tray LEDs, page Alarm Conditions, page RSP LEDsInterface Module LEDs Interface Module LEDsRSP LEDs continued Color/State OC-3 Interface Module LEDsT1/E1 Interface Module LEDs Description5-10 Power Supply LEDsFan Tray LEDs Color/StateAlarm Type Alarm Conditions5-11 Alarm MeaningCisco ASR 903 Router Hardware Installation Guide 5-12Chapter 5 Troubleshooting LED Summary OL-25178-04Site Log A P P E N D I X ADate Cisco ASR 903 Router Hardware Installation GuideDescription of Action Performed or Symptom Observed Table A-1I N D E IN-1IN-2