Manuals / Cisco Systems / Computer Equipment / Network Router

Cisco Systems ASR 903 manual

Models: ASR 903

1 118

Download 118 pages 26.92 Kb

Page 34

Warning Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035

Chapter 2 Preparing for Installation

Safety Guidelines

Warning Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035

Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036

Warning Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network voltages. Statement 1041

Warning This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260. Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The telecommunications lines must be disconnected 1) before unplugging the main power connector or 2) while the housing is open, or both. Statement 1043

Warning This product requires short-circuit (overturned) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045

Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046

Warning Never install an AC power module and a DC power module in the same chassis. Statement 1050

Warning Failure to securely tighten the power and relay connector captive screws can result in an electrical arc if the connector is accidentally removed. Statement 1058

Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use.

Warning If you connect or disconnect the console cable with power applied to the switch or any device on the network, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding. To verify switch operation, perform POST on the switch in a nonhazardous location before installation. Statement 1065

Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074

Cisco ASR 903 Router Hardware Installation Guide

2-6	OL-25178-04

Image 34

Cisco Systems ASR 903 manual

Contents

Cisco ASR 903 Router Hardware Installation Guide Cisco Systems, IncJune Text Part Number OL-25178-04THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS RSP Modules Obtaining Documentation and Submitting a Service RequestC O N T E N T S Dying GaspPreparing for Installation Safety GuidelinesInstalling the Chassis Brackets Precautions for Rack-MountingInstalling the Fan Tray RSP InstallationInstalling the Cisco Microsoft Windows USB Device Driver Installing an Interface ModuleUsing the Console Interface Connecting Ethernet CablesVerifying the Hardware Configuration TroubleshootingSite Log A-1 Alarm ConditionsFan Tray LEDs ContentsContents Cisco ASR 903 Router Hardware Installation Guide viiiOL-25178-04 Document Revision History Obtaining Documentation and Submitting a Service Request, pageAbout this Book Document AudienceInitial Configuration” Installation”Chapter 3, “Installing the Cisco ASR Chapter 5, “Troubleshooting”Obtaining Documentation and Submitting a Service Request Tip Means the following information will help you solve a problemChapter Cisco ASR 903 Router Hardware Installation Guide OL-25178-04Cisco ASR 903 Router Overview Cisco ASR 903 Router FeaturesC H A P T E R System Specifications Interface modulesDC Power Specifications, page Power Supply FeaturesRedundancy, page Dying Gasp, page Status LEDs, page Redundancy DC Power SpecificationsAC Power Specifications, page Dying GaspAC Power Specifications Fan TrayRSP Modules Supported RSP Features, page RSP Redundancy, pageNetwork Timing Interfaces, page RSP Interfaces, page Supported RSPs Supported RSP FeaturesRSP Redundancy Label Network Timing InterfacesRSP Interfaces InterfaceSupported SFP Modules Interface ModulesGigabit Ethernet SFP Interface Module Gigabit Ethernet SFP Interface Module, pageGigabit Ethernet RJ45 Interface Module 1-101-11 10 Gigabit Ethernet XFP Interface ModuleSupported SFP Modules 1-12 DWDM-XFP-46.92 DWDM-XFP-47.72 DWDM-XFP-48.51 DWDM-XFP-50.121-13 T1/E1 Interface ModuleFigure 1-7 16 x T1/E1 Interface Module 1-14 OC-3 Interface ModuleSupported SFP Modules Serial Number Label Location Temperature SensorInterface Numbering 1-151-16 Regulatory ComplianceInformation for the Cisco ASR 903 Router document Safety Guidelines, page Site Planning, page Preparing for InstallationSafety Guidelines Safety Guidelines for Personal Safety and Equipment Protection, pageStandard Warning Statements Safety Guidelines for Personal Safety and Equipment Protection Safety Precautions for Module Installation and RemovalSafety with Electricity Warning Use copper conductors only. Statement Warning Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement Page Power Supply Considerations Preventing ESD DamageGeneral Precautions, page Site Planning Checklist, page General PrecautionsSite Planning Checklist Floor Loading Considerations, page Site Power Guidelines, pageEnvironmental Requirements Physical CharacteristicsSite Selection Guidelines 2-10Air exhaust Air Flow Guidelines2-11 Room airFloor Loading Considerations Site Power GuidelinesAir Flow Guidelines for Enclosed Rack Installation 2-12Electrical Circuit Requirements Site Cabling Guidelines2-13 Electromagnetic Interference Asynchronous Terminal ConnectionsInterference Considerations Radio Frequency InterferencePrecautions for Rack-Mounting, page Rack Selection Guidelines, page Precautions for Rack-MountingLightning and AC Power Fault Interference Rack-Mounting GuidelinesEquipment Rack Guidelines Locating for SafetyLocating for Easy Maintenance 2-16Locating for Proper Airflow 2-17Installation Checklist 2-18Creating a Site Log Receiving the Cisco ASR 903 Router2-19 Tools and Equipment Chassis-Lifting Guidelines2-20 Statement Unpacking and Verifying the Shipped Contents2-21 2-22 Accessories kitPrerequisites, page Installing the Router in a Rack, page Installing the Cisco ASR 903 RouterInstalling the Router in a Rack Installing the Chassis Ground Connection, pageInstalling the Chassis Brackets Installing the Router Chassis in the Rack Figure 3-5 Installing the Chassis in a 300 mm ETSI Cabinet Attaching the Cable Management BracketsFigure 3-6 Cable Management Bracket Installation Installing the Chassis Ground Connection 0.5 in. 12.7 mm ± 0.02 in. 0.5 mm Figure 3-9 Stripping a Ground WireWire lead InsulationFigure 3-10 Crimping a Ground Lug onto the Ground Wire Installing the Fan Tray Removing and Replacing the Fan TrayFigure 3-12 Detaching the Fan Tray Captive installation screwHandle Hot-Swapping an RSP Module, page RSP InstallationInstalling an RSP Module, page Removing an RSP Module, page 3-10Installing an RSP Module 3-11Removing an RSP Module 3-12Hot-Swapping an RSP Module 3-13Installing an Interface Module, page Interface Module InstallationInstalling an Interface Module Removing an Interface Module, pageHot-Swapping an Interface Module Removing an Interface Module3-15 3-16 Caution To avoid erroneous failure messages, note the current configuration of all interfaces before you remove or replace an interface module, and allow at least 2 minutes for the system to reinitialize after a module has been removed or replaced. This time is recommended in order to allow for synchronization between components within the interface module and for synchronization with the standby RSPPreventing Power Loss, page Power Connection Guidelines, page Installing the Power SupplyPreventing Power Loss Installing the DC Power Supply, pageGuidelines for AC-Powered Systems Power Connection GuidelinesGuidelines for DC-Powered Systems 3-18Installing the DC Power Supply Module, page Installing the DC Power SupplyInstalling the DC Power Supply Module Installing the Terminal Block, pageInstalling the Terminal Block 3-203-21 Ground lead wire3-22 Torque is from 4.425 in.-lb .5 N-m to 5.310 in-lb .6 N-mActivating the DC Power Supply 3-23Statement Removing and Replacing the DC Power Supply3-24 StatementInstalling the AC Power Supply Module, page Installing the AC power SupplyInstalling the AC Power Supply Module Activating the AC Power Supply, pageActivating the AC Power Supply Removing and Replacing the AC Power Supply3-26 Connecting Console Cables, page Connecting the Cisco ASR 903 Router to the NetworkConnecting Console Cables Connecting to the Auxiliary Port, pageConnecting to the Serial Port using Microsoft Windows 3-28Connecting the Cisco ASR 903 Router to the Network 3-29Chapter 3 Installing the Cisco ASR 903 Router Cisco ASR 903 Router Hardware Installation GuideStep 1 Use the Finder to go to Applications Utilities Terminal Connecting to the Console Port using Mac OSConnecting to the Console Port using Linux 3-30Installing the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows USB Device DriverInstalling the Cisco Microsoft Windows XP USB Driver “Installing the Cisco Microsoft Windows XP USB Driver”Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver Uninstalling the Cisco Microsoft Windows USB DriverInstalling the Cisco Microsoft Windows Vista USB Driver “Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver”Uninstalling the Cisco Microsoft Windows Vista USB Driver Connecting to the Auxiliary Port3-33 3-34 To connect a modem to the router, follow these stepsConnecting a USB Flash Device Connecting a Management Ethernet CableInstalling and Removing SFP and XFP Modules 3-35Connecting Cables to the BITS Interface, page Connecting Timing CablesConnecting Cables to the BITS Interface Connecting Cables to a GPS Interface, page3-37 Step 4 Turn on power to the routerConnecting Cables to the Output 10Mhz or 1PPS Interface Connecting Cables to a GPS InterfaceConnecting Cables to the Input 10Mhz or 1PPS Interface Connecting Cables to the ToD InterfaceConnecting Ethernet Cables 3-39Installing the Cable Connector Connecting Cables to SFP ModulesConnecting T1/E1 cables 3-40For the T1/E1 ports, see the “T1/E1 Port Pinout” section on page Connecting Cables to the Patch PanelRJ45 Cable Pinouts 3-41Recommended Patch Panel Connecting the Fan Tray Alarm Port3-42 Chapter 3 Installing the Cisco ASR 903 Router Connector and Cable Specifications3-43 Connecting the Cisco ASR 903 Router to the NetworkConnecting the Cisco ASR 903 Router to the Network 3-44Chapter 3 Installing the Cisco ASR 903 Router Cisco ASR 903 Router Hardware Installation GuideConfiguring the Cisco ASR 903 Router at Startup, page Cisco ASR 903 Router Initial ConfigurationPowering Up the Cisco ASR 903 Router, page Safely Powering Off the Cisco ASR 903 Router, pagePowering Up the Cisco ASR 903 Router Example 4-1 Loading the Default System Boot ImageCisco ASR 903 Router Hardware Installation Guide Chapter 4 Cisco ASR 903 Router Initial ConfigurationPowering Up the Cisco ASR 903 Router initrd at 009B9000 isord at 01007000 0D1DF800 avail ram 00400000Powering Up the Cisco ASR 903 Router Chapter 4 Cisco ASR 903 Router Initial ConfigurationCisco ASR 903 Router Hardware Installation Guide Verifying the Front Panel LEDs Configuring the Cisco ASR 903 Router at StartupVerifying the Hardware Configuration Checking Hardware and Software CompatibilityUsing the Console Interface Configuring Global ParametersSaving the Running Configuration to NVRAM Checking the Running Configuration SettingsRouter# show running-config Safely Powering Off the Cisco ASR 903 Router USB Console Port Pinout, page Fiber-Optic Specifications, page TroubleshootingTime of Day Port Pinout, page Alarm Port Pinout, page PinoutsBITS Port Pinout continued GPS Port PinoutTime of Day Port Pinout GPS Port PinoutExternal Alarm Input Pinout Alarm Port PinoutConsole/Aux RJ45 RS232 Serial Port Pinout RJ45 1PPS/ToD Port Pinout continuedT1/E1 Port Pinout T1/E1 Interface PinoutsFan Tray Alarm Port Pinout Management Ethernet Port PinoutT1/E1 Interface Pinouts continued USB Flash/MEM Port Pinout Fiber-Optic SpecificationsUSB Console Port Pinout Single USB Console PortLED Summary RSP LEDs, page Interface Module LEDs, page Power Supply LEDs, pageFan Tray LEDs, page Alarm Conditions, page RSP LEDsRSP LEDs continued Interface Module LEDsInterface Module LEDs Color/State OC-3 Interface Module LEDsT1/E1 Interface Module LEDs Description5-10 Power Supply LEDsFan Tray LEDs Color/StateAlarm Type Alarm Conditions5-11 Alarm MeaningCisco ASR 903 Router Hardware Installation Guide 5-12Chapter 5 Troubleshooting LED Summary OL-25178-04Site Log A P P E N D I X ADate Cisco ASR 903 Router Hardware Installation GuideDescription of Action Performed or Symptom Observed Table A-1I N D E IN-1IN-2