Component Description | Cisco Systems ASR 903 manual

Chapter 2 Preparing for Installation

Receiving the Cisco ASR 903 Router

Table 2-2

Cisco ASR 903 Router Shipping Container Contents (continued)

Component

Description

Accessories kit	Chassis rack-mount brackets (19-inch EIA)

	Three sets of screws:
	• Front and rear rack-mount bracket screws (2 sets)
	• Cable-management bracket screws

	Six cable-management brackets (one per bracket)

	One earth lug with two 10-32 screws.

	1 RJ45 to RJ45 crossover cable
	1 RJ45 to DB-9 (female) adapter

ESD, wrist strap (disposable)	One disposable wrist strap (optional)

Documentation	Regulatory Compliance and Safety Information for the Cisco ASR 903 Router

Optional equipment	Check the container for the following optional equipment:
	• Power cord if an AC power supply was shipped. There are no cords for the DC
	power supply units.
	• T1/E1 cable connector (required only for T1/E1 interface modules)

Note Most Cisco documentation is available online. Documentation that is shipped with your Cisco ASR 903 Router includes the Regulatory Compliance and Safety Information for the

Cisco ASR 903 Router document, and the Cisco ASR 903 Router Documentation Roadmap that contains information about the various documents that are available online and the links to them.

	Cisco ASR 903 Router Hardware Installation Guide
2-22	OL-25178-04

Image 50

Cisco Systems ASR 903 manual Component Description

Contents

Cisco ASR 903 Router Hardware Installation Guide Page N T E N T S Site Planning RSP Installation Pinouts Fan Tray LEDs Viii Revision Date Change Summary Document Revision HistoryDocument Audience Title Description Document OrganizationDocument Conventions Convention Indication Obtaining Documentation and Submitting a Service Request Xii Cisco ASR 903 Router Features Cisco ASR 903 Router Overview System Specifications Cisco ASR 903 Router Chassis Design Power Supply Features Dying Gasp DC Power SpecificationsRedundancy Status LEDs AC Power Specifications Fan Tray RSP Modules 2shows the fan tray RSP Redundancy Supported RSP FeaturesSupported RSPs Label Interface Network Timing InterfacesRSP Interfaces Interface Modules Gigabit Ethernet SFP Interface Module Gigabit Ethernet RJ45 Interface Module 8 x 1 GE Gigabit Ethernet RJ45 Copper Interface Module Gigabit Ethernet XFP Interface Module 1 x 10 GE Gigabit Ethernet XFP Interface Module DWDM-XFP-C ONS-XC-10G-EP T1/E1 Interface Module 16 x T1/E1 Interface Module OC-3 Interface Module 8shows the interface module Serial Number Label Location Temperature SensorInterface Numbering Regulatory Compliance Cisco ASR 903 Router Overview Regulatory Compliance Preparing for Installation Safety Guidelines Standard Warning Statements Safety Precautions for Module Installation and Removal Safety with Electricity Page OL-25178-04 Preparing for Installation Safety Guidelines Power Supply Considerations Preventing ESD Damage Site Planning General PrecautionsSite Planning Checklist Environmental Requirements Physical CharacteristicsSite Selection Guidelines Air Flow Guidelines Air exhaust Room air Floor Loading Considerations Site Power GuidelinesAir Flow Guidelines for Enclosed Rack Installation Hardware components Site Cabling GuidelinesElectrical Circuit Requirements Asynchronous Terminal Connections Interference Considerations Rack Selection Guidelines Precautions for Rack-MountingRack-Mounting Guidelines Locating for Safety Equipment Rack Guidelines Locating for Proper Airflow Installation Checklist Verified Task Date Receiving the Cisco ASR 903 Router Creating a Site Log Chassis-Lifting Guidelines Tools and Equipment Unpacking and Verifying the Shipped Contents Component Description Installing the Router in a Rack Prerequisites Installing the Chassis Brackets Attaching Mounting Brackets for a 19-inch EIA Rack Installing the Router Chassis in the Rack Installing the Chassis in a 19-inch EIA Rack Installing the Chassis in a 300 mm Etsi Cabinet Attaching the Cable Management Brackets Installing the Chassis Ground Connection Grounding lug 300 mm Etsi cabinet Stripping a Ground Wire 10 Crimping a Ground Lug onto the Ground Wire Installing the Fan Tray Removing and Replacing the Fan Tray 12 Detaching the Fan Tray RSP Installation 13 Fan Tray Removal Installing an RSP Module 14 Cisco ASR 903 Router RSP Installation Removing an RSP Module Hot-Swapping an RSP Module Interface Module Installation Installing an Interface Module Removing an Interface Module Hot-Swapping an Interface Module OL-25178-04 Installing the Power Supply Preventing Power Loss Guidelines for AC-Powered Systems Power Connection GuidelinesGuidelines for DC-Powered Systems Installing the DC Power Supply Installing the DC Power Supply Module Installing the Terminal Block 16 Installing the DC Power Supply 17 DC Power Supply with Lead Wires 18 Torquing the DC Power Supply Terminal Block Plug Screws Activating the DC Power Supply Removing and Replacing the DC Power Supply Supply has been removed or replaced Installing the AC power Supply Installing the AC Power Supply Module Removing and Replacing the AC Power Supply Activating the AC Power Supply Connecting the Cisco ASR 903 Router to the Network Connecting Console Cables Connecting to the Serial Port using Microsoft Windows 2404 To disconnect the OS X USB console from the Terminal window Connecting to the Console Port using Mac OSConnecting to the Console Port using Linux Installing the Cisco Microsoft Windows USB Device Driver Installing the Cisco Microsoft Windows XP USB Driver Using the Setup.exe Program Uninstalling the Cisco Microsoft Windows USB DriverUsing the Add Remove Programs Utility Connecting to the Auxiliary Port Uninstalling the Cisco Microsoft Windows Vista USB Driver 23 Connecting a Modem to the Cisco ASR 903 Router Connecting a USB Flash Device Connecting a Management Ethernet CableInstalling and Removing SFP and XFP Modules Removing a USB Flash Device Connecting Timing CablesConnecting Cables to the Bits Interface OL-25178-04 Connecting Cables to a GPS Interface Connecting Cables to the Input 10Mhz or 1PPS Interface Connecting Ethernet Cables Installing the Cable Connector Connecting Cables to SFP ModulesConnecting T1/E1 cables Connecting Cables to the Patch Panel RJ45 Cable Pinouts Connecting the Fan Tray Alarm Port Recommended Patch Panel Connector and Cable Specifications OL-25178-04 Cisco ASR 903 Router Initial Configuration Checking Conditions Prior to System Startup Powering Up the Cisco ASR 903 Router Example 4-1 Loading the Default System Boot Image Cisco ASR 903 Router Hardware Installation Guide OL-25178-04 CPP Verifying the Front Panel LEDs Configuring the Cisco ASR 903 Router at StartupVerifying the Hardware Configuration Checking Hardware and Software Compatibility Using the Console Interface Configuring Global Parameters Checking the Running Configuration Settings Saving the Running Configuration to Nvram Safely Powering Off the Cisco ASR 903 Router Bits Port Pinout Pin Signal Name Direction DescriptionPinouts Mhz input and output 1PPS input and output GPS Port PinoutTime of Day Port Pinout Console/Aux RJ45 RS232 Serial Port Pinout Alarm Port PinoutPin Signal Name Description Board Telco Line Pins Signal Name Jack Pin Telco RX T1/E1 Port Pinout Management Ethernet Port Pinout USB Flash/MEM Port Pinout Fiber-Optic SpecificationsUSB Console Port Pinout Color/State Description two LEDs for eachT1/E1 port LED SummaryRSP LEDs Interface Module LEDs Color/State Description OC-3 Interface Module LEDs T1/E1 Interface Module LEDs Power Supply LEDs Fan Tray LEDs Alarm Conditions Alarm Type Alarm Meaning OL-25178-04 Site Log Date Initials D E IN-2