Configure a Static RIF Entry | Cisco Systems BC-109 manual

Configure Bridging of Routed Protocols

•

•

VINES

XNS

Enable use of the RIF only on Token Ring interfaces on the router.

To configure the Cisco IOS software to append RIF information, use the following command in interface configuration mode:

Command	Purpose
multiring {protocol-keyword[all-routes spanning] all	Enable collection and use of RIF
other}	information.

For an example of how to configure the software to bridge routed protocols, see the “SRB and Routing Certain Protocols Example” section later in this chapter.

Configure a Static RIF Entry

If a Token Ring host does not support the use of IEEE 802.2 TEST or XID datagrams as explorer packets, you might need to add static information to the RIF cache of the router.

To configure a static RIF entry, use the following command in global configuration mode:

Command	Purpose
rif mac-address rif-string {interface-name ring-group	Enter static source-route information
ring}	into the RIF cache.

Configure the RIF Timeout Interval

RIF information that can be used to bridge routed protocols is maintained in a cache whose entries are aged.

Note The rif validate enable commands have no effect on remote entries learned over RSRB.

To configure the number of minutes an inactive RIF entry is kept in the cache, use the following commands in global configuration mode:

Step	Command	Purpose
1	rif timeout minutes	Specify the number of minutes an inactive
		RIF entry is kept.

2	rif validate-enable	Enable RIF validation for entries learned on
		an interface (Token Ring or FDDI).

3	rif validate-enable-age	Enable RIF validation on an SRB that is
		malfunctioning.

4	rif validate-enable-route-cache	Enable synchronization of the RIF cache with
		the protocol route cache.

BC-118Bridging and IBM Networking Configuration Guide

Image 10

Cisco Systems BC-109 manual Configure a Static RIF Entry, Configure the RIF Timeout Interval

Contents

Configuring Source-Route Bridging SRB Configuration Task List Configure Source-Route Bridging Configure a Dual-Port Bridge Configure a Multiport Bridge Using a Virtual Ring Multiple Dual-Port Bridges Source-bridge ring-group ring-group Define a Ring Group in SRB ContextNo source-bridge ring-group ring-group Interface fddi slot/port Configure SRB over FddiEnable SRB and Assign a Ring Group to an Interface Source-bridge route-cache cbus Configure Fast-Switching SRB over Fddi Configure SRB over Frame Relay Enable the Automatic Spanning-Tree Function Limit the Maximum SRB Hops Configure Bridging of Routed Protocols Enable Use of the RIF Configure a Static RIF Entry Configure the RIF Timeout Interval Overview of SR/TLB Following notes and caveats apply to all uses of SR/TLB Enable Translation Compatibility with IBM 8209 Bridges Enable Bridging between Transparent Bridging and SRBDisable Fast-Switched SR/TLB No source-bridge transparent ring-group fastswitch Enable Standard Token Ring LLC2-to-Ethernet LLC2 Conversion Enable Token Ring LLC2-to-Ethernet ConversionEnable 0x80d5 Processing Source-bridge sap-80d5 dsap Configure NetBIOS Support Specify Timeout and Enable NetBIOS Name Caching Source-bridge proxy-netbios-only Create Static Entries in the NetBIOS Name Cache Configure the NetBIOS Cache Name LengthEnable NetBIOS Proxying Specify Dead-Time Intervals for NetBIOS Packets Netbios name-cache query-timeout seconds Configure LNM SupportNetbios name-cache recognized-timeout seconds LNM Linking to a Source-Route Bridge on Each Local Ring How a Router Works with LNM LAN Network Manager Monitoring and Translating Disable LNM Functionality Disable Automatic Report Path Trace Function Enable Other LRMs to Change Router Parameters Enable LNM Servers Apply a Password to an LNM Reporting LinkChange Reporting Thresholds Monitor LNM Operation Change an LNM Reporting IntervalLnm softerr milliseconds Configure NetBIOS Access Filters Using Station Names Configure NetBIOS Access FiltersSecure the SRB Network Netbios access-list bytes name permit deny offset Configure NetBIOS Access Filters Using a Byte OffsetNetbios access-list host name permit deny pattern Netbios input-access-filter bytes name Netbios output-access-filter bytes name Configure Administrative Filters for Token Ring TrafficFilter Frames by Protocol Type Filter Source Addresses Filter Frames by Vendor CodeFilter Destination Addresses Access Expression Example Configure Access Expressions Optimize Access Expressions Alter Access Lists Used in Access Expressions Tune the SRB Network Enable or Disable the Source-Route Fast-Switching Cache Establish the Connection Timeout Interval Enable or Disable the SSEOptimize Explorer Processing Controlling Explorer Storms in Redundant Network Topologies Establish SRB Interoperability with TI MAC Firmware Configure Proxy ExplorersMac-address ieee-address Report Spurious Frame-Copied Errors Monitor and Maintain the SRB Network SRB Configuration Examples Source-bridge tcp-queue-max number Dual-Port Source-Route Bridge Configuration Basic SRB with Spanning-Tree Explorers Example Optimized Explorer Processing Configuration Example SRB-Only Example SRB and Routing Certain Protocols Example Multiport SRB Example Configuration for Router a SRB with Multiple Virtual Ring Groups Example Configuration for Router B SRB over Fddi Configuration ExamplesSRB over Fddi Fast-Switching Example Router a SRB over Frame Relay Configuration Example Frad Using SRB over Frame Relay to Connect to a Cisco Router Configuration on Router C Configuration of Router aConfiguration on Router B Adding a Static RIF Cache Entry Example Adding a Static RIF Cache Entry for a Two-Hop Path Example SR/TLB for a Simple Network Example BC-154Bridging and IBM Networking Configuration Guide SR/TLB with Access Filtering Example Example of a Bit-Swapped Address NetBIOS Support with a Static NetBIOS Cache Entry Example Specifying a Static Entry Wayfarer# show lnm config LNM for a Simple Network Example LNM for a More Complex Network Example NetBIOS Access Filters Example Filtering Bridged Token Ring Packets to IBM Machines Example Shows a router connecting four Token Rings Creating Access Filters Example Following access expression would result Access Filters Example Fast-Switching Example Autonomous Switching Example