Cisco Systems BC-109 instruction

SRB Configuration Examples

Assume that the following configuration for SRB and transparent bridging existed before you wanted to enable SR/TLB:

interface tokenring 0 source-bridge 1 1 2

!

interface tokenring 1 source-bridge 2 1 1

!

interface ethernet 0 bridge-group 1

!

interface ethernet 0 bridge-group 1

!

bridge 1 protocol dec

To enable SR/TLB, one aspect of this configuration must change immediately—a third ring must be configured. Before SR/TLB, the two Token Ring interfaces were communicating with two-port local source-route bridging; after SR/TLB, these two interfaces must be reconfigured to communicate through a virtual ring, as follows:

source-bridge ring-group 10

!

interface tokenring 0 source-bridge 1 1 10

!

interface tokenring 1 source-bridge 2 1 10

!

interface ethernet 0 bridge-group 1

!

interface ethernet 1 bridge-group 1

!

bridge 1 protocol dec

Now you are ready to determine two things:

•A ring number for the pseudo-ring that is unique throughout the source-route bridged network. For the preceding example configuration, use the number 3.

•A bridge number for the path to the pseudo-ring. For the preceding example configuration, use the number 1.

BC-154Bridging and IBM Networking Configuration Guide

Image 46

Cisco Systems BC-109 manual BC-154Bridging and IBM Networking Configuration Guide

Contents

Configuring Source-Route Bridging SRB Configuration Task List Configure Source-Route Bridging Configure a Dual-Port Bridge Configure a Multiport Bridge Using a Virtual Ring Multiple Dual-Port Bridges Source-bridge ring-group ring-group Define a Ring Group in SRB ContextNo source-bridge ring-group ring-group Interface fddi slot/port Configure SRB over FddiEnable SRB and Assign a Ring Group to an Interface Source-bridge route-cache cbus Configure Fast-Switching SRB over Fddi Configure SRB over Frame Relay Enable the Automatic Spanning-Tree Function Limit the Maximum SRB Hops Configure Bridging of Routed Protocols Enable Use of the RIF Configure a Static RIF Entry Configure the RIF Timeout Interval Overview of SR/TLB Following notes and caveats apply to all uses of SR/TLB Enable Translation Compatibility with IBM 8209 Bridges Enable Bridging between Transparent Bridging and SRBDisable Fast-Switched SR/TLB No source-bridge transparent ring-group fastswitch Enable Standard Token Ring LLC2-to-Ethernet LLC2 Conversion Enable Token Ring LLC2-to-Ethernet ConversionEnable 0x80d5 Processing Source-bridge sap-80d5 dsap Configure NetBIOS Support Specify Timeout and Enable NetBIOS Name Caching Source-bridge proxy-netbios-only Create Static Entries in the NetBIOS Name Cache Configure the NetBIOS Cache Name LengthEnable NetBIOS Proxying Specify Dead-Time Intervals for NetBIOS Packets Netbios name-cache query-timeout seconds Configure LNM SupportNetbios name-cache recognized-timeout seconds LNM Linking to a Source-Route Bridge on Each Local Ring How a Router Works with LNM LAN Network Manager Monitoring and Translating Disable LNM Functionality Disable Automatic Report Path Trace Function Enable Other LRMs to Change Router Parameters Enable LNM Servers Apply a Password to an LNM Reporting LinkChange Reporting Thresholds Monitor LNM Operation Change an LNM Reporting IntervalLnm softerr milliseconds Configure NetBIOS Access Filters Using Station Names Configure NetBIOS Access FiltersSecure the SRB Network Netbios access-list bytes name permit deny offset Configure NetBIOS Access Filters Using a Byte OffsetNetbios access-list host name permit deny pattern Netbios input-access-filter bytes name Netbios output-access-filter bytes name Configure Administrative Filters for Token Ring TrafficFilter Frames by Protocol Type Filter Source Addresses Filter Frames by Vendor CodeFilter Destination Addresses Access Expression Example Configure Access Expressions Optimize Access Expressions Alter Access Lists Used in Access Expressions Tune the SRB Network Enable or Disable the Source-Route Fast-Switching Cache Establish the Connection Timeout Interval Enable or Disable the SSEOptimize Explorer Processing Controlling Explorer Storms in Redundant Network Topologies Establish SRB Interoperability with TI MAC Firmware Configure Proxy ExplorersMac-address ieee-address Report Spurious Frame-Copied Errors Monitor and Maintain the SRB Network SRB Configuration Examples Source-bridge tcp-queue-max number Dual-Port Source-Route Bridge Configuration Basic SRB with Spanning-Tree Explorers Example Optimized Explorer Processing Configuration Example SRB-Only Example SRB and Routing Certain Protocols Example Multiport SRB Example Configuration for Router a SRB with Multiple Virtual Ring Groups Example Configuration for Router B SRB over Fddi Configuration ExamplesSRB over Fddi Fast-Switching Example Router a SRB over Frame Relay Configuration Example Frad Using SRB over Frame Relay to Connect to a Cisco Router Configuration on Router C Configuration of Router aConfiguration on Router B Adding a Static RIF Cache Entry Example Adding a Static RIF Cache Entry for a Two-Hop Path Example SR/TLB for a Simple Network Example BC-154Bridging and IBM Networking Configuration Guide SR/TLB with Access Filtering Example Example of a Bit-Swapped Address NetBIOS Support with a Static NetBIOS Cache Entry Example Specifying a Static Entry Wayfarer# show lnm config LNM for a Simple Network Example LNM for a More Complex Network Example NetBIOS Access Filters Example Filtering Bridged Token Ring Packets to IBM Machines Example Shows a router connecting four Token Rings Creating Access Filters Example Following access expression would result Access Filters Example Fast-Switching Example Autonomous Switching Example