135 | Cisco Systems OL-14253-01 manual

Appendix A Notifications, Fault Management, and Probable Cause Mapping

Probable Cause Mapping

Table A-35	CTM GateWay/CORBA Mapping for the ONS 15600 SDH R8.0 (continued)

			CTM Internal Index (Not
TMF Mapping		NE Native Probable Cause	Reported in the Notification)

UNIDENTIFIED		Automatic SNCP switch caused by LOP	17791

UNIDENTIFIED		Automatic SNCP switch caused by UNEQ	17792

UNIDENTIFIED		Automatic SNCP switch caused by SFBER	17793

UNIDENTIFIED		Automatic SNCP switch caused by SDBER	17794

UNIDENTIFIED		Failure to switch to protection—high order path	17795

UNIDENTIFIED		MSSP multinode table update completed	17796

UNIDENTIFIED		Bipolar violation	17797

UNIDENTIFIED		High order path—payload defect indication	17798

UNIDENTIFIED		MSSP software version mismatch	17799

DCC_FAILURE		Regenerator section—DCC termination failure	17800

EQPT		Battery failure	17801

UNIDENTIFIED		Extreme high voltage	17802

UNIDENTIFIED		Extreme low voltage	17803

UNIDENTIFIED		High voltage	17804

UNIDENTIFIED		Low voltage	17805

UNIDENTIFIED		Voltage reading mismatch between SC cards	17806

EQPT		Wavelength out of lock	17807

EQPT		Automatic laser shutdown	17808

UNIDENTIFIED		Ring is squelching high order traffic	17809

EQPT		Non-Cisco PPM inserted	17810

EQPT		Unqualified PPM inserted	17811

A.5.17 CTM GateWay/CORBA Mapping—ONS 1580x

The following table lists the CTM GateWay/CORBA mapping for the ONS 1580x.

Table A-36		CTM GateWay/CORBA Mapping for the ONS 1580x

						CTM
						Internal
	TMF Mapping		NE Native Probable Cause	NE Native Alarm Description		Index

	UNIDENTIFIED		Condition unknown	UNK		500

	TX_FAIL		Operating temperature 1 fail low	T-AWG_TEMP-1-LOW_TEMP		501

	TX_FAIL		Operating temperature 1 fail high	T-AWG_TEMP-1-HIGH_TEMP		502

	TX_DEGRADE		Operating temperature 1 degrade low	T-AWG_TEMP-1-LMID_TEMP		503

	TX_DEGRADE		Operating temperature 1 degrade high	T-AWG_TEMP-1-HMID_TEMP		504

	TX_DEGRADE		Laser 1 current degrade	T-LASCURR-1-DEGRADE		505

			Cisco Transport Manager Release 8.5 GateWay/CORBA User Guide and Programmer Manual


	OL-14253-01						A-135
	OL-14253-01						A-135

Image 135

Cisco Systems OL-14253-01 appendix 135

Contents

Notifications, Fault Management, and Probable Cause Mapping Resolving the Notification Service Object Creation MultiLayerSubnetworkRollT Object DeletionMultiLayerSubnetworkL2TopologyT MultiLayerSubnetworkMLVLANT Attribute Value Change State Change Event HolderState-State change. CTM supports the following values CommunicationState-CTM supports the following valuesEmsInSyncState-CTM supports the following values True Protection Switch RollState-CTM supports the following valuesVcatState-CTM supports the following values Value Threshold Crossing Alert Alarm Heartbeat Event Backup Status Event TMF-Defined Probable Cause Probable Cause Mapping CTM GateWay/CORBA Mapping-MGX 8880/8850/8830 CTM GateWay/CORBA Mapping-EMS Snmp throttle error 62418 Upload file error 62410Stats file error 62416 Stats file transfer error 62417 Front card upgraded 60120 Front card failed, no backup 60109Front card in update mode 60112 Front card in program mode 60118 Secondary card held in reset 60504 Primary card in program mode 60418Primary card upgraded 60420 Primary card in hold mode 60422 Receiving signal MF OOF 60711 Secondary card in hold mode 60522Controller in standby mode 60601 Redundant card switch over 60661 Stats alarm, PES 24-hour threshold exceeded 61102 Path signal label mismatch 60924Path signal receiving Locd 60928 Stats alarm, PES current 15-minute threshold exceeded 61101 Stats alarm, UAS 24-hour threshold exceeded 61108 Stats alarm, Pses 24-hour threshold exceeded 61104Stats alarm, Sefs 24-hour threshold exceeded 61106 Stats alarm, UAS current 15-minute threshold exceeded 61107 Stats alarm, Sonet section, total CVs 61304 Stats alarm, Sonet section, total ESs 61301Stats alarm, Sonet section, total SESs 61302 Stats alarm, Sonet section, total SEFSs 61303 APS alarms, wrong request 61514 APS alarms, standby line alarm 61511APS alarms, standby line loopback 61512 APS alarms, direction mismatch 61513 Media gateway link state, out of service 60612 Connection alarm, primary failure 62601Connection alarm, secondary failure 62602 Media gateway link state, pending in service 60611 CID state, failed 60241 MTP signaling gateway route available 66013MTP signaling gateway route unavailable 66014 MTP signaling gateway route restricted 66015 CTM GateWay/CORBA Mapping-ONS Loss of output power 8606 Unknown alarm 8601Excessive pump 1 laser temperature 8604 Excessive pump 2 laser temperature 8605 Fiber temperature out of range 8717 Power fail low LINE1TX port 8711Power fail low LINE2RX port 8712 Case temperature out of range 8716 Alarm condition detected on an alarm input port 19018 Degraded signal defect 19009Excessive error defect 19015 Server signal failure 19017 Error occurred during initialization 19056 Reset of the router/bridge required 19050Automatic switchover to backup link, main link fault 19052 Connection failed frame relay switch and WAN gate 19054 Switch to working 19088 Automatic switchover to backup link, main link fault 19082T0 sync switch 19084 Switch to protection 19087 Excessive switching 25003 MSP command timeout 19115MSP command overruled 19116 External error 25002 Severely errored frame 25030 Loss of signal 25022Remote alarm indication 25025 Signal degrade 25029 Failure to switch to protection 25071 Software fault or failure 25056Software fault-data integrity fault 25057 High temperature 25065 Manual switch to secondary reference 25095 Manual system reset 25092Manual switch to internal clock 25093 Manual switch to primary reference 25094 Failure to switch to protection-span 25157 Diagnostics failure 25153Medium access control failure 25154 Failure to switch to protection-ring 25156 Forced switch to protection-ring 25164 Manual switch to protection-span 25161Forced switch back to working-ring 25162 Forced switch back to working-span 25163 TCC B to shelf slot 4 Drop 4 communication failure 25196 Fast start synchronization mode 25211Alarm indication signal-VT 25214 Signal label mismatch failure-unequipped-VT 25217 Automatic path-protection switch caused by Uneq 25241 Failure to switch to protection-path 25235Automatic path-protection switch caused by AIS 25239 Automatic path-protection switch caused by LOP 25240 Lockout switch request on facility-equipment 25270 System reboot 25267Manual switch request on facility-equipment 25268 Forced switch request on facility or equipment 25269 APS channel-far-end protection line signal degrade 25303 Far-end BER threshold passed for signal failure-span 25300Far-end BER threshold passed for signal degrade-ring 25301 Far-end BER threshold passed for signal degrade-span 25302 BER threshold exceeded for signal failure-line 25338 Inhibit switch to working request on equipment 25335BER threshold exceeded for signal degrade-line 25336 BER threshold exceeded for signal degrade-path 25337 Far-end E1 equipment failure service affecting 25374 E1 loopback command sent to far end 25370E3 loopback due to Feac command 25371 Far-end E1 equipment failure non-service affecting 25373 BER threshold exceeded for signal degrade-low order 25414 Alarms/events suppressed for this object 25411BER threshold exceeded for signal degrade-high order 25412 BER threshold exceeded for signal failure-high order 25413 Database backup failed 25457 Login of user 25446Error in startup config 25454 No startup config 25455 ODUk-signal failure 25491 Equipment low Rx power 25484Equipment low Tx power 25485 OTUk-signal failure 25490 Standby database out of sync 25522 Redundant power capability lost 25523Configuration events 28001 Authentication failure notification 28004 Fopaps Third synchronization reference failure 25042 Powerfail restart 25102 Dccfailure Fopaps AIS Uneq Far-end Idle 25260 Far-end LOS 25261Far-end LOF 25262 Far end of fiber is provisioned with different ring ID 25314 TIM high order-trace identifier mismatch failure 25353 Uneq LMP neighbor discovery failed 25427 Eqpt Equipment low Rx temperature 25479 LAN connection polarity reversed 25527 Optical power degrade low 25531Optical power degrade high 25532 Laser temperature degrade 25542 AWG temperature degrade 25551 Laser auto power reduction 25547Case temperature degrade 25548 Fiber temperature degrade 25549 Remote alarm indication in Tx 25592 Disable inactive user 25584Disable inactive user 25585 Alarm indication signal in Tx 25591 Plug-in module range settings mismatch 25621 Incoming overhead signal absent 25617Optical safety remote interlock on 25618 Automatic power control correction skipped 25620 ODUk-4-alarm indication signal 25655 ODUk-1-alarm indication signal 25652ODUk-2-alarm indication signal 25653 ODUk-3-alarm indication signal 25654 ENV PLM High temperature 25065 Dccfailure Payload bus failure to I/O slot 16 Xcon slot 25135 Fopaps AIS ENV LOS Securityviolation AIS Far-end E3 equipment failure non-service affecting 25378 LOM AIS Bersd FEC mismatch 25529 Loss of frame in Tx 25593 Incoming payload signal absent 25616 Blsr software version mismatch 25672 VT path trace identifier mismatch 25671 Switching matrix module failure-working 25682 Bridge and roll is pending a valid signal 25674User password change required 25678 Remote authentication fail 25679 High order path-excessive errors 25711 Multiplex section-signal degraded 25708Multiplex section-excessive errors 25709 High order path-signal degraded 25710 Port add power fail low 25750 Idle signal condition 25747Idle signal condition in TX 25748 Automatic power control correction skipped 25749 Input signal level out of range 14705 Bert enabled 25763Temperature out of range 14703 Electrical power level is unacceptable 14704 Access to Idprom failed 9502 Cannot access multiple line card 9055Cannot access backplane Idprom 9057 Access to TSP card failed 9501 Loss of signal event 10102 Chassis power supply 0 missing 12606Chassis power supply 1 missing 12607 Power supply unit failed 12701 Access to Idprom failed 10802 Access to Escon card failed 10701Access to Idprom failed 10702 Access to card failed 10801 Access to Idprom failed 11702 Access to 2.5G card failed 11601Access to Idprom failed 11602 Access to card failed 11701 Waveport 1 opt switch failed 9204 Access to LRC failed 9201Access to Idprom failed 9202 Waveport 0 opt switch failed 9203 Trunk laser failure detected 9504 HEC failure threshold exceeded 9978HEC degrade threshold exceeded 9979 Access to Idprom failed 11102 Loss of signal event in Cisco OPT-MON-MIB 10302Trunk laser shut down by laser safety control 10307 Access to card failed 11101 Optical Monitoring Alarms-ONS 15530 and ONS Tx laser temp exceeds high alarm threshold 14547 Rx ambient temp below low alarm threshold 14535Tx ambient temp below low alarm threshold 14536 Rx laser temp exceeds high alarm threshold 14546 CTM GateWay/CORBA Mapping-ONS 15600 Sonet Far-end BER threshold passed for signal degrade-span 17026 BER threshold exceeded for signal degrade-line 17023BER threshold exceeded for signal degrade-path 17024 Far-end BER threshold passed for signal degrade-ring 17025 Equipment fails to boot 17064 Free running synchronization mode 17058Stratum 3E fast start synchronization mode 17059 Holdover synchronization mode 17060 100 101 102 103 104 105 106 107 108 109 110 111 Control bus failure-I/O-TSC a 17575 Control bus failure-I/O-TSC B 17576112 113 114 115 116 Equipment high laser bias 17754 Database backup failed 17751Database restore failed 17752 Isis adjacency failure 17753 118 119 CTM GateWay/CORBA Mapping-ONS 15600 SDH 120 121 122 123 124 125 126 127 128 129 130 131 132 Eqpt problem on carrier or PIM 17724 Eqpt problem on PIM or PPM 17725133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148