Env | Cisco Systems OL-14253-01 manual

Appendix A Notifications, Fault Management, and Probable Cause Mapping

Probable Cause Mapping

A.5.8 CTM GateWay/CORBA Mapping—ONS 15310 CL, ONS 15454 SONET, and ONS 15454 SDH R6.0 and R8.0; ONS 15327 R6.0

The following table lists the CTM GateWay/CORBA mapping for the ONS 15310 CL, ONS 15454 SONET, and ONS 15454 SDH R6.0 and R8.0, and for the ONS 15327 R6.0.

Table A-24 CTM GateWay/CORBA Mapping for the ONS 15310 CL, ONS 15454 SONET, and ONS 15454 SDH R6.0 and R8.0; ONS 15327 R6.0

			CTM Internal Index (Not
	TMF Mapping	NE Native Probable Cause	Reported in the Notification)

	UNIDENTIFIED	Normal condition	25000

	ENV	Failure detected external to the NE	25001

	ENV	External error	25002

	UNIDENTIFIED	Excessive switching	25003

	UNIDENTIFIED	Incoming failure condition	25004

	AIS	Alarm indication signal	25005

	AIS	Alarm indication signal—line	25006

	AIS	Alarm indication signal—path	25007

	FOP_APS	APS channel failure	25008

	FOP_APS	Byte failure	25009

	FOP_APS	Protection switching channel match failure	25010

	FOP_APS	Automatic protection switch mode mismatch	25011

	FOP_APS	Far-end protection line failure	25012

	UNIDENTIFIED	Bipolar violation	25013

	UNIDENTIFIED	Carrier loss on the LAN	25014

	UNIDENTIFIED	STS concatenation error	25015

	UNIDENTIFIED	Excess collisions on the LAN	25016

	UNIDENTIFIED	Facility failure	25017

	UNIDENTIFIED	Far-end block error	25018

	LOF	Loss of frame	25019

	LOP	Loss of pointer	25020

	LOP	Loss of pointer—path	25021

	LOS	Loss of signal	25022

	UNIDENTIFIED	Out of frame	25023

	UNIDENTIFIED	Path selector failure	25024

	RAI	Remote alarm indication	25025

	RAI	Remote failure indication	25026

	RAI	Remote failure indication—line	25027

	RAI	Remote failure indication—path	25028

	BER_SD	Signal degrade	25029

		Cisco Transport Manager Release 8.5 GateWay/CORBA User Guide and Programmer Manual


	OL-14253-01				A-65
	OL-14253-01				A-65

Image 65

Cisco Systems OL-14253-01 appendix Env

Contents

Notifications, Fault Management, and Probable Cause Mapping Resolving the Notification Service Object Creation MultiLayerSubnetworkL2TopologyT Object DeletionMultiLayerSubnetworkMLVLANT MultiLayerSubnetworkRollT Attribute Value Change State Change Event EmsInSyncState-CTM supports the following values CommunicationState-CTM supports the following valuesTrue HolderState-State change. CTM supports the following values VcatState-CTM supports the following values Protection SwitchRollState-CTM supports the following values Value Threshold Crossing Alert Alarm Heartbeat Event Backup Status Event TMF-Defined Probable Cause Probable Cause Mapping CTM GateWay/CORBA Mapping-MGX 8880/8850/8830 CTM GateWay/CORBA Mapping-EMS Stats file error 62416 Upload file error 62410Stats file transfer error 62417 Snmp throttle error 62418 Front card in update mode 60112 Front card failed, no backup 60109Front card in program mode 60118 Front card upgraded 60120 Primary card upgraded 60420 Primary card in program mode 60418Primary card in hold mode 60422 Secondary card held in reset 60504 Controller in standby mode 60601 Secondary card in hold mode 60522Redundant card switch over 60661 Receiving signal MF OOF 60711 Path signal receiving Locd 60928 Path signal label mismatch 60924Stats alarm, PES current 15-minute threshold exceeded 61101 Stats alarm, PES 24-hour threshold exceeded 61102 Stats alarm, Sefs 24-hour threshold exceeded 61106 Stats alarm, Pses 24-hour threshold exceeded 61104Stats alarm, UAS current 15-minute threshold exceeded 61107 Stats alarm, UAS 24-hour threshold exceeded 61108 Stats alarm, Sonet section, total SESs 61302 Stats alarm, Sonet section, total ESs 61301Stats alarm, Sonet section, total SEFSs 61303 Stats alarm, Sonet section, total CVs 61304 APS alarms, standby line loopback 61512 APS alarms, standby line alarm 61511APS alarms, direction mismatch 61513 APS alarms, wrong request 61514 Connection alarm, secondary failure 62602 Connection alarm, primary failure 62601Media gateway link state, pending in service 60611 Media gateway link state, out of service 60612 MTP signaling gateway route unavailable 66014 MTP signaling gateway route available 66013MTP signaling gateway route restricted 66015 CID state, failed 60241 CTM GateWay/CORBA Mapping-ONS Excessive pump 1 laser temperature 8604 Unknown alarm 8601Excessive pump 2 laser temperature 8605 Loss of output power 8606 Power fail low LINE2RX port 8712 Power fail low LINE1TX port 8711Case temperature out of range 8716 Fiber temperature out of range 8717 Excessive error defect 19015 Degraded signal defect 19009Server signal failure 19017 Alarm condition detected on an alarm input port 19018 Automatic switchover to backup link, main link fault 19052 Reset of the router/bridge required 19050Connection failed frame relay switch and WAN gate 19054 Error occurred during initialization 19056 T0 sync switch 19084 Automatic switchover to backup link, main link fault 19082Switch to protection 19087 Switch to working 19088 MSP command overruled 19116 MSP command timeout 19115External error 25002 Excessive switching 25003 Remote alarm indication 25025 Loss of signal 25022Signal degrade 25029 Severely errored frame 25030 Software fault-data integrity fault 25057 Software fault or failure 25056High temperature 25065 Failure to switch to protection 25071 Manual switch to internal clock 25093 Manual system reset 25092Manual switch to primary reference 25094 Manual switch to secondary reference 25095 Medium access control failure 25154 Diagnostics failure 25153Failure to switch to protection-ring 25156 Failure to switch to protection-span 25157 Forced switch back to working-ring 25162 Manual switch to protection-span 25161Forced switch back to working-span 25163 Forced switch to protection-ring 25164 Alarm indication signal-VT 25214 Fast start synchronization mode 25211Signal label mismatch failure-unequipped-VT 25217 TCC B to shelf slot 4 Drop 4 communication failure 25196 Automatic path-protection switch caused by AIS 25239 Failure to switch to protection-path 25235Automatic path-protection switch caused by LOP 25240 Automatic path-protection switch caused by Uneq 25241 Manual switch request on facility-equipment 25268 System reboot 25267Forced switch request on facility or equipment 25269 Lockout switch request on facility-equipment 25270 Far-end BER threshold passed for signal degrade-ring 25301 Far-end BER threshold passed for signal failure-span 25300Far-end BER threshold passed for signal degrade-span 25302 APS channel-far-end protection line signal degrade 25303 BER threshold exceeded for signal degrade-line 25336 Inhibit switch to working request on equipment 25335BER threshold exceeded for signal degrade-path 25337 BER threshold exceeded for signal failure-line 25338 E3 loopback due to Feac command 25371 E1 loopback command sent to far end 25370Far-end E1 equipment failure non-service affecting 25373 Far-end E1 equipment failure service affecting 25374 BER threshold exceeded for signal degrade-high order 25412 Alarms/events suppressed for this object 25411BER threshold exceeded for signal failure-high order 25413 BER threshold exceeded for signal degrade-low order 25414 Error in startup config 25454 Login of user 25446No startup config 25455 Database backup failed 25457 Equipment low Tx power 25485 Equipment low Rx power 25484OTUk-signal failure 25490 ODUk-signal failure 25491 Configuration events 28001 Redundant power capability lost 25523Authentication failure notification 28004 Standby database out of sync 25522 Fopaps Third synchronization reference failure 25042 Powerfail restart 25102 Dccfailure Fopaps AIS Uneq Far-end LOF 25262 Far-end Idle 25260Far-end LOS 25261 Far end of fiber is provisioned with different ring ID 25314 TIM high order-trace identifier mismatch failure 25353 Uneq LMP neighbor discovery failed 25427 Eqpt Equipment low Rx temperature 25479 Optical power degrade high 25532 Optical power degrade low 25531Laser temperature degrade 25542 LAN connection polarity reversed 25527 Case temperature degrade 25548 Laser auto power reduction 25547Fiber temperature degrade 25549 AWG temperature degrade 25551 Disable inactive user 25585 Disable inactive user 25584Alarm indication signal in Tx 25591 Remote alarm indication in Tx 25592 Optical safety remote interlock on 25618 Incoming overhead signal absent 25617Automatic power control correction skipped 25620 Plug-in module range settings mismatch 25621 ODUk-2-alarm indication signal 25653 ODUk-1-alarm indication signal 25652ODUk-3-alarm indication signal 25654 ODUk-4-alarm indication signal 25655 ENV PLM High temperature 25065 Dccfailure Payload bus failure to I/O slot 16 Xcon slot 25135 Fopaps AIS ENV LOS Securityviolation AIS Far-end E3 equipment failure non-service affecting 25378 LOM AIS Bersd FEC mismatch 25529 Loss of frame in Tx 25593 Incoming payload signal absent 25616 Blsr software version mismatch 25672 VT path trace identifier mismatch 25671 User password change required 25678 Bridge and roll is pending a valid signal 25674Remote authentication fail 25679 Switching matrix module failure-working 25682 Multiplex section-excessive errors 25709 Multiplex section-signal degraded 25708High order path-signal degraded 25710 High order path-excessive errors 25711 Idle signal condition in TX 25748 Idle signal condition 25747Automatic power control correction skipped 25749 Port add power fail low 25750 Temperature out of range 14703 Bert enabled 25763Electrical power level is unacceptable 14704 Input signal level out of range 14705 Cannot access backplane Idprom 9057 Cannot access multiple line card 9055Access to TSP card failed 9501 Access to Idprom failed 9502 Chassis power supply 1 missing 12607 Chassis power supply 0 missing 12606Power supply unit failed 12701 Loss of signal event 10102 Access to Idprom failed 10702 Access to Escon card failed 10701Access to card failed 10801 Access to Idprom failed 10802 Access to Idprom failed 11602 Access to 2.5G card failed 11601Access to card failed 11701 Access to Idprom failed 11702 Access to Idprom failed 9202 Access to LRC failed 9201Waveport 0 opt switch failed 9203 Waveport 1 opt switch failed 9204 HEC degrade threshold exceeded 9979 Trunk laser failure detected 9504HEC failure threshold exceeded 9978 Trunk laser shut down by laser safety control 10307 Loss of signal event in Cisco OPT-MON-MIB 10302Access to card failed 11101 Access to Idprom failed 11102 Optical Monitoring Alarms-ONS 15530 and ONS Tx ambient temp below low alarm threshold 14536 Rx ambient temp below low alarm threshold 14535Rx laser temp exceeds high alarm threshold 14546 Tx laser temp exceeds high alarm threshold 14547 CTM GateWay/CORBA Mapping-ONS 15600 Sonet BER threshold exceeded for signal degrade-path 17024 BER threshold exceeded for signal degrade-line 17023Far-end BER threshold passed for signal degrade-ring 17025 Far-end BER threshold passed for signal degrade-span 17026 Stratum 3E fast start synchronization mode 17059 Free running synchronization mode 17058Holdover synchronization mode 17060 Equipment fails to boot 17064 100 101 102 103 104 105 106 107 108 109 110 111 112 Control bus failure-I/O-TSC a 17575Control bus failure-I/O-TSC B 17576 113 114 115 116 Database restore failed 17752 Database backup failed 17751Isis adjacency failure 17753 Equipment high laser bias 17754 118 119 CTM GateWay/CORBA Mapping-ONS 15600 SDH 120 121 122 123 124 125 126 127 128 129 130 131 132 133 Eqpt problem on carrier or PIM 17724Eqpt problem on PIM or PPM 17725 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148