FTP transfer failed 62409, Down 60033 | Cisco Systems OL-14253-01

Appendix A Notifications, Fault Management, and Probable Cause Mapping

Probable Cause Mapping

Table A-17				CTM GateWay/CORBA Mapping for the MGX 8880/8850/8830 (continued)

						CTM Internal Index (Not
						Reported in the
	TMF Mapping				NE Native Probable Cause	Notification)

	EMS				FTP transfer failed	62409

	EMS				Upload file error	62410

	EMS				Minus 2 trap	62411

	EMS				Card lost trap	62412

	EMS				SNMP retry exceeded	62413

	EMS				FTP retry exceeded	62414

	EMS				Stats file error	62416

	EMS				Stats file transfer error	62417

	EMS				SNMP throttle error	62418

	EMS				Backoff failed	62419

	EMS				SNMP timeout	62420

	EMS				FTP session timeout	62421

	EMS				FTP transfer timeout	62422

	EMS				Unknown error	62448

	EMS				Initialization error	62449

	EMS				Communication error in ILOG	62452

	EMS				Communication error in shared memory	62453

	EMS				Communication error in CORBA	62454

	EMS				NTS registration failed	62456

	EMS				NTS trap loss	62457

	EMS				PM error	62459

	EMS				Process restarted	62502

	Shelf-Level Peripheral Alarms

	EQPT				Above normal	60031

	EQPT				Below normal	60032

	EQPT				Down	60033

	EQPT				Power failure	60034

	Card-Level Alarms for all Supported Cards on MGX8880/8850/8830

	EQPT				Front card not present	60101

	EQPT				Front card failed	60102

	EQPT				Front card in self test	60103

	EQPT				Front card held in reset	60104

	EQPT				Front card in boot	60105

	EQPT				Front card mismatch	60106

	EQPT				Front card unknown alarm	60107

			Cisco Transport Manager Release 8.5 GateWay/CORBA User Guide and Programmer Manual


	A-14					OL-14253-01
	A-14					OL-14253-01

Image 14

Cisco Systems OL-14253-01 FTP transfer failed 62409, Upload file error 62410, Minus 2 trap 62411, Card lost trap 62412

Contents

Notifications, Fault Management, and Probable Cause Mapping Resolving the Notification Service Object Creation MultiLayerSubnetworkMLVLANT Object DeletionMultiLayerSubnetworkL2TopologyT MultiLayerSubnetworkRollT Attribute Value Change State Change Event True CommunicationState-CTM supports the following valuesEmsInSyncState-CTM supports the following values HolderState-State change. CTM supports the following values VcatState-CTM supports the following values Protection SwitchRollState-CTM supports the following values Threshold Crossing Alert Value Alarm Backup Status Event Heartbeat Event Probable Cause Mapping TMF-Defined Probable Cause CTM GateWay/CORBA Mapping-EMS CTM GateWay/CORBA Mapping-MGX 8880/8850/8830 Stats file transfer error 62417 Upload file error 62410Stats file error 62416 Snmp throttle error 62418 Front card in program mode 60118 Front card failed, no backup 60109Front card in update mode 60112 Front card upgraded 60120 Primary card in hold mode 60422 Primary card in program mode 60418Primary card upgraded 60420 Secondary card held in reset 60504 Redundant card switch over 60661 Secondary card in hold mode 60522Controller in standby mode 60601 Receiving signal MF OOF 60711 Stats alarm, PES current 15-minute threshold exceeded 61101 Path signal label mismatch 60924Path signal receiving Locd 60928 Stats alarm, PES 24-hour threshold exceeded 61102 Stats alarm, UAS current 15-minute threshold exceeded 61107 Stats alarm, Pses 24-hour threshold exceeded 61104Stats alarm, Sefs 24-hour threshold exceeded 61106 Stats alarm, UAS 24-hour threshold exceeded 61108 Stats alarm, Sonet section, total SEFSs 61303 Stats alarm, Sonet section, total ESs 61301Stats alarm, Sonet section, total SESs 61302 Stats alarm, Sonet section, total CVs 61304 APS alarms, direction mismatch 61513 APS alarms, standby line alarm 61511APS alarms, standby line loopback 61512 APS alarms, wrong request 61514 Media gateway link state, pending in service 60611 Connection alarm, primary failure 62601Connection alarm, secondary failure 62602 Media gateway link state, out of service 60612 MTP signaling gateway route restricted 66015 MTP signaling gateway route available 66013MTP signaling gateway route unavailable 66014 CID state, failed 60241 CTM GateWay/CORBA Mapping-ONS Excessive pump 2 laser temperature 8605 Unknown alarm 8601Excessive pump 1 laser temperature 8604 Loss of output power 8606 Case temperature out of range 8716 Power fail low LINE1TX port 8711Power fail low LINE2RX port 8712 Fiber temperature out of range 8717 Server signal failure 19017 Degraded signal defect 19009Excessive error defect 19015 Alarm condition detected on an alarm input port 19018 Connection failed frame relay switch and WAN gate 19054 Reset of the router/bridge required 19050Automatic switchover to backup link, main link fault 19052 Error occurred during initialization 19056 Switch to protection 19087 Automatic switchover to backup link, main link fault 19082T0 sync switch 19084 Switch to working 19088 External error 25002 MSP command timeout 19115MSP command overruled 19116 Excessive switching 25003 Signal degrade 25029 Loss of signal 25022Remote alarm indication 25025 Severely errored frame 25030 High temperature 25065 Software fault or failure 25056Software fault-data integrity fault 25057 Failure to switch to protection 25071 Manual switch to primary reference 25094 Manual system reset 25092Manual switch to internal clock 25093 Manual switch to secondary reference 25095 Failure to switch to protection-ring 25156 Diagnostics failure 25153Medium access control failure 25154 Failure to switch to protection-span 25157 Forced switch back to working-span 25163 Manual switch to protection-span 25161Forced switch back to working-ring 25162 Forced switch to protection-ring 25164 Signal label mismatch failure-unequipped-VT 25217 Fast start synchronization mode 25211Alarm indication signal-VT 25214 TCC B to shelf slot 4 Drop 4 communication failure 25196 Automatic path-protection switch caused by LOP 25240 Failure to switch to protection-path 25235Automatic path-protection switch caused by AIS 25239 Automatic path-protection switch caused by Uneq 25241 Forced switch request on facility or equipment 25269 System reboot 25267Manual switch request on facility-equipment 25268 Lockout switch request on facility-equipment 25270 Far-end BER threshold passed for signal degrade-span 25302 Far-end BER threshold passed for signal failure-span 25300Far-end BER threshold passed for signal degrade-ring 25301 APS channel-far-end protection line signal degrade 25303 BER threshold exceeded for signal degrade-path 25337 Inhibit switch to working request on equipment 25335BER threshold exceeded for signal degrade-line 25336 BER threshold exceeded for signal failure-line 25338 Far-end E1 equipment failure non-service affecting 25373 E1 loopback command sent to far end 25370E3 loopback due to Feac command 25371 Far-end E1 equipment failure service affecting 25374 BER threshold exceeded for signal failure-high order 25413 Alarms/events suppressed for this object 25411BER threshold exceeded for signal degrade-high order 25412 BER threshold exceeded for signal degrade-low order 25414 No startup config 25455 Login of user 25446Error in startup config 25454 Database backup failed 25457 OTUk-signal failure 25490 Equipment low Rx power 25484Equipment low Tx power 25485 ODUk-signal failure 25491 Authentication failure notification 28004 Redundant power capability lost 25523Configuration events 28001 Standby database out of sync 25522 Fopaps Third synchronization reference failure 25042 Powerfail restart 25102 Dccfailure Fopaps AIS Uneq Far-end LOF 25262 Far-end Idle 25260Far-end LOS 25261 Far end of fiber is provisioned with different ring ID 25314 TIM high order-trace identifier mismatch failure 25353 Uneq LMP neighbor discovery failed 25427 Eqpt Equipment low Rx temperature 25479 Laser temperature degrade 25542 Optical power degrade low 25531Optical power degrade high 25532 LAN connection polarity reversed 25527 Fiber temperature degrade 25549 Laser auto power reduction 25547Case temperature degrade 25548 AWG temperature degrade 25551 Alarm indication signal in Tx 25591 Disable inactive user 25584Disable inactive user 25585 Remote alarm indication in Tx 25592 Automatic power control correction skipped 25620 Incoming overhead signal absent 25617Optical safety remote interlock on 25618 Plug-in module range settings mismatch 25621 ODUk-3-alarm indication signal 25654 ODUk-1-alarm indication signal 25652ODUk-2-alarm indication signal 25653 ODUk-4-alarm indication signal 25655 ENV PLM High temperature 25065 Dccfailure Payload bus failure to I/O slot 16 Xcon slot 25135 Fopaps AIS ENV LOS Securityviolation AIS Far-end E3 equipment failure non-service affecting 25378 LOM AIS Bersd FEC mismatch 25529 Loss of frame in Tx 25593 Incoming payload signal absent 25616 VT path trace identifier mismatch 25671 Blsr software version mismatch 25672 Remote authentication fail 25679 Bridge and roll is pending a valid signal 25674User password change required 25678 Switching matrix module failure-working 25682 High order path-signal degraded 25710 Multiplex section-signal degraded 25708Multiplex section-excessive errors 25709 High order path-excessive errors 25711 Automatic power control correction skipped 25749 Idle signal condition 25747Idle signal condition in TX 25748 Port add power fail low 25750 Electrical power level is unacceptable 14704 Bert enabled 25763Temperature out of range 14703 Input signal level out of range 14705 Access to TSP card failed 9501 Cannot access multiple line card 9055Cannot access backplane Idprom 9057 Access to Idprom failed 9502 Power supply unit failed 12701 Chassis power supply 0 missing 12606Chassis power supply 1 missing 12607 Loss of signal event 10102 Access to card failed 10801 Access to Escon card failed 10701Access to Idprom failed 10702 Access to Idprom failed 10802 Access to card failed 11701 Access to 2.5G card failed 11601Access to Idprom failed 11602 Access to Idprom failed 11702 Waveport 0 opt switch failed 9203 Access to LRC failed 9201Access to Idprom failed 9202 Waveport 1 opt switch failed 9204 HEC degrade threshold exceeded 9979 Trunk laser failure detected 9504HEC failure threshold exceeded 9978 Access to card failed 11101 Loss of signal event in Cisco OPT-MON-MIB 10302Trunk laser shut down by laser safety control 10307 Access to Idprom failed 11102 Optical Monitoring Alarms-ONS 15530 and ONS Rx laser temp exceeds high alarm threshold 14546 Rx ambient temp below low alarm threshold 14535Tx ambient temp below low alarm threshold 14536 Tx laser temp exceeds high alarm threshold 14547 CTM GateWay/CORBA Mapping-ONS 15600 Sonet Far-end BER threshold passed for signal degrade-ring 17025 BER threshold exceeded for signal degrade-line 17023BER threshold exceeded for signal degrade-path 17024 Far-end BER threshold passed for signal degrade-span 17026 Holdover synchronization mode 17060 Free running synchronization mode 17058Stratum 3E fast start synchronization mode 17059 Equipment fails to boot 17064 100 101 102 103 104 105 106 107 108 109 110 111 112 Control bus failure-I/O-TSC a 17575Control bus failure-I/O-TSC B 17576 113 114 115 116 Isis adjacency failure 17753 Database backup failed 17751Database restore failed 17752 Equipment high laser bias 17754 118 CTM GateWay/CORBA Mapping-ONS 15600 SDH 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 Eqpt problem on carrier or PIM 17724Eqpt problem on PIM or PPM 17725 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148