High temperature 25065 | Cisco Systems OL-14253-01 specification

Appendix A Notifications, Fault Management, and Probable Cause Mapping

				Probable Cause Mapping
Table A-24		CTM GateWay/CORBA Mapping for the ONS 15310 CL, ONS 15454 SONET, and ONS 15454 SDH R6.0 and
		R8.0; ONS 15327 R6.0 (continued)

				CTM Internal Index (Not
	TMF Mapping		NE Native Probable Cause	Reported in the Notification)

	EQPT		High temperature	25065

	EQPT		Facility termination equipment failure	25066

	EQPT		Automatic laser shutdown	25067

	UNIDENTIFIED		Failure to release from protection	25068

	EQPT		Receiver failure	25069

	EQPT		Transmit failure	25070

	UNIDENTIFIED		Failure to switch to protection	25071

	UNIDENTIFIED		Equipment unit plug-in	25072

	UNIDENTIFIED		Internal power failure	25073

	UNIDENTIFIED		Fuse alarm	25074

	UNIDENTIFIED		Synchronization unit failure	25075

	UNIDENTIFIED		Synchronization switching equipment failure	25076

	EQPT		Equipment unit unplugged	25077

	EQPT		Manually caused abnormal condition	25078

	UNIDENTIFIED		Manual alarm cutoff	25079

	UNIDENTIFIED		Procedural error	25080

	EQPT		Improper removal	25081

	UNIDENTIFIED		Protection unit not available	25082

	UNIDENTIFIED		Protection switch	25083

	UNIDENTIFIED		Recovery or service protection action has been initiated	25084

	UNIDENTIFIED		Automatic system reset	25085

	UNIDENTIFIED		Cold restart	25086

	UNIDENTIFIED		Forced switch back to working	25087

	UNIDENTIFIED		Forced switch to protection	25088

	UNIDENTIFIED		Initialization initiated	25089

	UNIDENTIFIED		Lockout of protection	25090

	UNIDENTIFIED		Lockout of working	25091

	UNIDENTIFIED		Manual system reset	25092

	UNIDENTIFIED		Manual switch to internal clock	25093

	UNIDENTIFIED		Manual switch to primary reference	25094

	UNIDENTIFIED		Manual switch to secondary reference	25095

	UNIDENTIFIED		Manual switch to third reference	25096

	UNIDENTIFIED		Manual switch to fourth reference	25097

	UNIDENTIFIED		Manual switch to fifth reference	25098

	UNIDENTIFIED		Manual switch to sixth reference	25099

			Cisco Transport Manager Release 8.5 GateWay/CORBA User Guide and Programmer Manual


	OL-14253-01					A-67
	OL-14253-01					A-67

Image 67

Cisco Systems OL-14253-01 appendix High temperature 25065

Contents

Notifications, Fault Management, and Probable Cause Mapping Resolving the Notification Service Object Creation MultiLayerSubnetworkRollT Object DeletionMultiLayerSubnetworkL2TopologyT MultiLayerSubnetworkMLVLANT Attribute Value Change State Change Event HolderState-State change. CTM supports the following values CommunicationState-CTM supports the following valuesEmsInSyncState-CTM supports the following values True RollState-CTM supports the following values Protection SwitchVcatState-CTM supports the following values Value Threshold Crossing Alert Alarm Heartbeat Event Backup Status Event TMF-Defined Probable Cause Probable Cause Mapping CTM GateWay/CORBA Mapping-MGX 8880/8850/8830 CTM GateWay/CORBA Mapping-EMS Snmp throttle error 62418 Upload file error 62410Stats file error 62416 Stats file transfer error 62417 Front card upgraded 60120 Front card failed, no backup 60109Front card in update mode 60112 Front card in program mode 60118 Secondary card held in reset 60504 Primary card in program mode 60418Primary card upgraded 60420 Primary card in hold mode 60422 Receiving signal MF OOF 60711 Secondary card in hold mode 60522Controller in standby mode 60601 Redundant card switch over 60661 Stats alarm, PES 24-hour threshold exceeded 61102 Path signal label mismatch 60924Path signal receiving Locd 60928 Stats alarm, PES current 15-minute threshold exceeded 61101 Stats alarm, UAS 24-hour threshold exceeded 61108 Stats alarm, Pses 24-hour threshold exceeded 61104Stats alarm, Sefs 24-hour threshold exceeded 61106 Stats alarm, UAS current 15-minute threshold exceeded 61107 Stats alarm, Sonet section, total CVs 61304 Stats alarm, Sonet section, total ESs 61301Stats alarm, Sonet section, total SESs 61302 Stats alarm, Sonet section, total SEFSs 61303 APS alarms, wrong request 61514 APS alarms, standby line alarm 61511APS alarms, standby line loopback 61512 APS alarms, direction mismatch 61513 Media gateway link state, out of service 60612 Connection alarm, primary failure 62601Connection alarm, secondary failure 62602 Media gateway link state, pending in service 60611 CID state, failed 60241 MTP signaling gateway route available 66013MTP signaling gateway route unavailable 66014 MTP signaling gateway route restricted 66015 CTM GateWay/CORBA Mapping-ONS Loss of output power 8606 Unknown alarm 8601Excessive pump 1 laser temperature 8604 Excessive pump 2 laser temperature 8605 Fiber temperature out of range 8717 Power fail low LINE1TX port 8711Power fail low LINE2RX port 8712 Case temperature out of range 8716 Alarm condition detected on an alarm input port 19018 Degraded signal defect 19009Excessive error defect 19015 Server signal failure 19017 Error occurred during initialization 19056 Reset of the router/bridge required 19050Automatic switchover to backup link, main link fault 19052 Connection failed frame relay switch and WAN gate 19054 Switch to working 19088 Automatic switchover to backup link, main link fault 19082T0 sync switch 19084 Switch to protection 19087 Excessive switching 25003 MSP command timeout 19115MSP command overruled 19116 External error 25002 Severely errored frame 25030 Loss of signal 25022Remote alarm indication 25025 Signal degrade 25029 Failure to switch to protection 25071 Software fault or failure 25056Software fault-data integrity fault 25057 High temperature 25065 Manual switch to secondary reference 25095 Manual system reset 25092Manual switch to internal clock 25093 Manual switch to primary reference 25094 Failure to switch to protection-span 25157 Diagnostics failure 25153Medium access control failure 25154 Failure to switch to protection-ring 25156 Forced switch to protection-ring 25164 Manual switch to protection-span 25161Forced switch back to working-ring 25162 Forced switch back to working-span 25163 TCC B to shelf slot 4 Drop 4 communication failure 25196 Fast start synchronization mode 25211Alarm indication signal-VT 25214 Signal label mismatch failure-unequipped-VT 25217 Automatic path-protection switch caused by Uneq 25241 Failure to switch to protection-path 25235Automatic path-protection switch caused by AIS 25239 Automatic path-protection switch caused by LOP 25240 Lockout switch request on facility-equipment 25270 System reboot 25267Manual switch request on facility-equipment 25268 Forced switch request on facility or equipment 25269 APS channel-far-end protection line signal degrade 25303 Far-end BER threshold passed for signal failure-span 25300Far-end BER threshold passed for signal degrade-ring 25301 Far-end BER threshold passed for signal degrade-span 25302 BER threshold exceeded for signal failure-line 25338 Inhibit switch to working request on equipment 25335BER threshold exceeded for signal degrade-line 25336 BER threshold exceeded for signal degrade-path 25337 Far-end E1 equipment failure service affecting 25374 E1 loopback command sent to far end 25370E3 loopback due to Feac command 25371 Far-end E1 equipment failure non-service affecting 25373 BER threshold exceeded for signal degrade-low order 25414 Alarms/events suppressed for this object 25411BER threshold exceeded for signal degrade-high order 25412 BER threshold exceeded for signal failure-high order 25413 Database backup failed 25457 Login of user 25446Error in startup config 25454 No startup config 25455 ODUk-signal failure 25491 Equipment low Rx power 25484Equipment low Tx power 25485 OTUk-signal failure 25490 Standby database out of sync 25522 Redundant power capability lost 25523Configuration events 28001 Authentication failure notification 28004 Fopaps Third synchronization reference failure 25042 Powerfail restart 25102 Dccfailure Fopaps AIS Uneq Far-end LOS 25261 Far-end Idle 25260Far-end LOF 25262 Far end of fiber is provisioned with different ring ID 25314 TIM high order-trace identifier mismatch failure 25353 Uneq LMP neighbor discovery failed 25427 Eqpt Equipment low Rx temperature 25479 LAN connection polarity reversed 25527 Optical power degrade low 25531Optical power degrade high 25532 Laser temperature degrade 25542 AWG temperature degrade 25551 Laser auto power reduction 25547Case temperature degrade 25548 Fiber temperature degrade 25549 Remote alarm indication in Tx 25592 Disable inactive user 25584Disable inactive user 25585 Alarm indication signal in Tx 25591 Plug-in module range settings mismatch 25621 Incoming overhead signal absent 25617Optical safety remote interlock on 25618 Automatic power control correction skipped 25620 ODUk-4-alarm indication signal 25655 ODUk-1-alarm indication signal 25652ODUk-2-alarm indication signal 25653 ODUk-3-alarm indication signal 25654 ENV PLM High temperature 25065 Dccfailure Payload bus failure to I/O slot 16 Xcon slot 25135 Fopaps AIS ENV LOS Securityviolation AIS Far-end E3 equipment failure non-service affecting 25378 LOM AIS Bersd FEC mismatch 25529 Loss of frame in Tx 25593 Incoming payload signal absent 25616 Blsr software version mismatch 25672 VT path trace identifier mismatch 25671 Switching matrix module failure-working 25682 Bridge and roll is pending a valid signal 25674User password change required 25678 Remote authentication fail 25679 High order path-excessive errors 25711 Multiplex section-signal degraded 25708Multiplex section-excessive errors 25709 High order path-signal degraded 25710 Port add power fail low 25750 Idle signal condition 25747Idle signal condition in TX 25748 Automatic power control correction skipped 25749 Input signal level out of range 14705 Bert enabled 25763Temperature out of range 14703 Electrical power level is unacceptable 14704 Access to Idprom failed 9502 Cannot access multiple line card 9055Cannot access backplane Idprom 9057 Access to TSP card failed 9501 Loss of signal event 10102 Chassis power supply 0 missing 12606Chassis power supply 1 missing 12607 Power supply unit failed 12701 Access to Idprom failed 10802 Access to Escon card failed 10701Access to Idprom failed 10702 Access to card failed 10801 Access to Idprom failed 11702 Access to 2.5G card failed 11601Access to Idprom failed 11602 Access to card failed 11701 Waveport 1 opt switch failed 9204 Access to LRC failed 9201Access to Idprom failed 9202 Waveport 0 opt switch failed 9203 HEC failure threshold exceeded 9978 Trunk laser failure detected 9504HEC degrade threshold exceeded 9979 Access to Idprom failed 11102 Loss of signal event in Cisco OPT-MON-MIB 10302Trunk laser shut down by laser safety control 10307 Access to card failed 11101 Optical Monitoring Alarms-ONS 15530 and ONS Tx laser temp exceeds high alarm threshold 14547 Rx ambient temp below low alarm threshold 14535Tx ambient temp below low alarm threshold 14536 Rx laser temp exceeds high alarm threshold 14546 CTM GateWay/CORBA Mapping-ONS 15600 Sonet Far-end BER threshold passed for signal degrade-span 17026 BER threshold exceeded for signal degrade-line 17023BER threshold exceeded for signal degrade-path 17024 Far-end BER threshold passed for signal degrade-ring 17025 Equipment fails to boot 17064 Free running synchronization mode 17058Stratum 3E fast start synchronization mode 17059 Holdover synchronization mode 17060 100 101 102 103 104 105 106 107 108 109 110 111 Control bus failure-I/O-TSC B 17576 Control bus failure-I/O-TSC a 17575112 113 114 115 116 Equipment high laser bias 17754 Database backup failed 17751Database restore failed 17752 Isis adjacency failure 17753 118 119 CTM GateWay/CORBA Mapping-ONS 15600 SDH 120 121 122 123 124 125 126 127 128 129 130 131 132 Eqpt problem on PIM or PPM 17725 Eqpt problem on carrier or PIM 17724133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148