124 | Cisco Systems OL-14253-01 guide

Appendix A Notifications, Fault Management, and Probable Cause Mapping

Probable Cause Mapping

Table A-34			CTM GateWay/CORBA Mapping for the ONS 15600 SDH R1.4 (continued)

					CTM Internal Index (Not
	TMF Mapping			NE Native Probable Cause	Reported in the Notification)

	UNIDENTIFIED			Manual switch to second reference	50150

	UNIDENTIFIED			Manual switch to third reference	50152

	UNIDENTIFIED			Manual switch request on facility/equipment	50153

	UNIDENTIFIED			Manual switch request on ring	50154

	UNIDENTIFIED			Manual switch request on span	50155

	UNIDENTIFIED			Powerfail restart	50156

	UNIDENTIFIED			Ring switch is active on the east side	50157

	UNIDENTIFIED			Ring switch is active on the west side	50158

	UNIDENTIFIED			Span switch is active on the east side	50159

	UNIDENTIFIED			Span switch is active on the west side	50160

	UNIDENTIFIED			Ring is squelching traffic	50161

	UNIDENTIFIED			Squelching path	50162

	UNIDENTIFIED			Software download in progress	50163

	UNIDENTIFIED			Switch to primary reference	50166

	UNIDENTIFIED			Switch to second reference	50167

	UNIDENTIFIED			Switch to third reference	50169

	ENV			System reboot	50170

	UNIDENTIFIED			Switched back to working unit	50171

	UNIDENTIFIED			Switched to protection unit	50172

	UNIDENTIFIED			Warm restart	50173

	UNIDENTIFIED			Waiting to restore	50174

	UNIDENTIFIED			Bridge and roll has occurred	50175

	UNIDENTIFIED			Bridge and roll is pending a valid signal	50176

	UNIDENTIFIED			Inhibit switch to protect request on equipment	50177

	UNIDENTIFIED			Inhibit switch to working request on equipment	50178

	UNIDENTIFIED			Exercise request on ring failed	50179

	UNIDENTIFIED			Exercise request on span failed	50180

	UNIDENTIFIED			Exercising ring successfully	50181

	UNIDENTIFIED			Exercising span successfully	50182

	UNIDENTIFIED			Unidirectional full pass-through is active	50185

	UNIDENTIFIED			Bidirectional full pass-through is active	50186

	UNIDENTIFIED			K bytes pass-through is active	50187

	UNIDENTIFIED			Ring is segmented	50188

	UNIDENTIFIED			Ring topology is under construction	50189

	UNIDENTIFIED			Duplicate node ID	50190

			Cisco Transport Manager Release 8.5 GateWay/CORBA User Guide and Programmer Manual


	A-124				OL-14253-01
	A-124				OL-14253-01

Image 124

Cisco Systems OL-14253-01 appendix 124

Contents

Notifications, Fault Management, and Probable Cause Mapping Resolving the Notification Service Object Creation Object Deletion MultiLayerSubnetworkL2TopologyTMultiLayerSubnetworkMLVLANT MultiLayerSubnetworkRollT Attribute Value Change State Change Event CommunicationState-CTM supports the following values EmsInSyncState-CTM supports the following valuesTrue HolderState-State change. CTM supports the following values RollState-CTM supports the following values Protection SwitchVcatState-CTM supports the following values Threshold Crossing Alert Value Alarm Backup Status Event Heartbeat Event Probable Cause Mapping TMF-Defined Probable Cause CTM GateWay/CORBA Mapping-EMS CTM GateWay/CORBA Mapping-MGX 8880/8850/8830 Upload file error 62410 Stats file error 62416Stats file transfer error 62417 Snmp throttle error 62418 Front card failed, no backup 60109 Front card in update mode 60112Front card in program mode 60118 Front card upgraded 60120 Primary card in program mode 60418 Primary card upgraded 60420Primary card in hold mode 60422 Secondary card held in reset 60504 Secondary card in hold mode 60522 Controller in standby mode 60601Redundant card switch over 60661 Receiving signal MF OOF 60711 Path signal label mismatch 60924 Path signal receiving Locd 60928Stats alarm, PES current 15-minute threshold exceeded 61101 Stats alarm, PES 24-hour threshold exceeded 61102 Stats alarm, Pses 24-hour threshold exceeded 61104 Stats alarm, Sefs 24-hour threshold exceeded 61106Stats alarm, UAS current 15-minute threshold exceeded 61107 Stats alarm, UAS 24-hour threshold exceeded 61108 Stats alarm, Sonet section, total ESs 61301 Stats alarm, Sonet section, total SESs 61302Stats alarm, Sonet section, total SEFSs 61303 Stats alarm, Sonet section, total CVs 61304 APS alarms, standby line alarm 61511 APS alarms, standby line loopback 61512APS alarms, direction mismatch 61513 APS alarms, wrong request 61514 Connection alarm, primary failure 62601 Connection alarm, secondary failure 62602Media gateway link state, pending in service 60611 Media gateway link state, out of service 60612 MTP signaling gateway route available 66013 MTP signaling gateway route unavailable 66014MTP signaling gateway route restricted 66015 CID state, failed 60241 CTM GateWay/CORBA Mapping-ONS Unknown alarm 8601 Excessive pump 1 laser temperature 8604Excessive pump 2 laser temperature 8605 Loss of output power 8606 Power fail low LINE1TX port 8711 Power fail low LINE2RX port 8712Case temperature out of range 8716 Fiber temperature out of range 8717 Degraded signal defect 19009 Excessive error defect 19015Server signal failure 19017 Alarm condition detected on an alarm input port 19018 Reset of the router/bridge required 19050 Automatic switchover to backup link, main link fault 19052Connection failed frame relay switch and WAN gate 19054 Error occurred during initialization 19056 Automatic switchover to backup link, main link fault 19082 T0 sync switch 19084Switch to protection 19087 Switch to working 19088 MSP command timeout 19115 MSP command overruled 19116External error 25002 Excessive switching 25003 Loss of signal 25022 Remote alarm indication 25025Signal degrade 25029 Severely errored frame 25030 Software fault or failure 25056 Software fault-data integrity fault 25057High temperature 25065 Failure to switch to protection 25071 Manual system reset 25092 Manual switch to internal clock 25093Manual switch to primary reference 25094 Manual switch to secondary reference 25095 Diagnostics failure 25153 Medium access control failure 25154Failure to switch to protection-ring 25156 Failure to switch to protection-span 25157 Manual switch to protection-span 25161 Forced switch back to working-ring 25162Forced switch back to working-span 25163 Forced switch to protection-ring 25164 Fast start synchronization mode 25211 Alarm indication signal-VT 25214Signal label mismatch failure-unequipped-VT 25217 TCC B to shelf slot 4 Drop 4 communication failure 25196 Failure to switch to protection-path 25235 Automatic path-protection switch caused by AIS 25239Automatic path-protection switch caused by LOP 25240 Automatic path-protection switch caused by Uneq 25241 System reboot 25267 Manual switch request on facility-equipment 25268Forced switch request on facility or equipment 25269 Lockout switch request on facility-equipment 25270 Far-end BER threshold passed for signal failure-span 25300 Far-end BER threshold passed for signal degrade-ring 25301Far-end BER threshold passed for signal degrade-span 25302 APS channel-far-end protection line signal degrade 25303 Inhibit switch to working request on equipment 25335 BER threshold exceeded for signal degrade-line 25336BER threshold exceeded for signal degrade-path 25337 BER threshold exceeded for signal failure-line 25338 E1 loopback command sent to far end 25370 E3 loopback due to Feac command 25371Far-end E1 equipment failure non-service affecting 25373 Far-end E1 equipment failure service affecting 25374 Alarms/events suppressed for this object 25411 BER threshold exceeded for signal degrade-high order 25412BER threshold exceeded for signal failure-high order 25413 BER threshold exceeded for signal degrade-low order 25414 Login of user 25446 Error in startup config 25454No startup config 25455 Database backup failed 25457 Equipment low Rx power 25484 Equipment low Tx power 25485OTUk-signal failure 25490 ODUk-signal failure 25491 Redundant power capability lost 25523 Configuration events 28001Authentication failure notification 28004 Standby database out of sync 25522 Fopaps Third synchronization reference failure 25042 Powerfail restart 25102 Dccfailure Fopaps AIS Uneq Far-end LOS 25261 Far-end Idle 25260Far-end LOF 25262 Far end of fiber is provisioned with different ring ID 25314 TIM high order-trace identifier mismatch failure 25353 Uneq LMP neighbor discovery failed 25427 Eqpt Equipment low Rx temperature 25479 Optical power degrade low 25531 Optical power degrade high 25532Laser temperature degrade 25542 LAN connection polarity reversed 25527 Laser auto power reduction 25547 Case temperature degrade 25548Fiber temperature degrade 25549 AWG temperature degrade 25551 Disable inactive user 25584 Disable inactive user 25585Alarm indication signal in Tx 25591 Remote alarm indication in Tx 25592 Incoming overhead signal absent 25617 Optical safety remote interlock on 25618Automatic power control correction skipped 25620 Plug-in module range settings mismatch 25621 ODUk-1-alarm indication signal 25652 ODUk-2-alarm indication signal 25653ODUk-3-alarm indication signal 25654 ODUk-4-alarm indication signal 25655 ENV PLM High temperature 25065 Dccfailure Payload bus failure to I/O slot 16 Xcon slot 25135 Fopaps AIS ENV LOS Securityviolation AIS Far-end E3 equipment failure non-service affecting 25378 LOM AIS Bersd FEC mismatch 25529 Loss of frame in Tx 25593 Incoming payload signal absent 25616 VT path trace identifier mismatch 25671 Blsr software version mismatch 25672 Bridge and roll is pending a valid signal 25674 User password change required 25678Remote authentication fail 25679 Switching matrix module failure-working 25682 Multiplex section-signal degraded 25708 Multiplex section-excessive errors 25709High order path-signal degraded 25710 High order path-excessive errors 25711 Idle signal condition 25747 Idle signal condition in TX 25748Automatic power control correction skipped 25749 Port add power fail low 25750 Bert enabled 25763 Temperature out of range 14703Electrical power level is unacceptable 14704 Input signal level out of range 14705 Cannot access multiple line card 9055 Cannot access backplane Idprom 9057Access to TSP card failed 9501 Access to Idprom failed 9502 Chassis power supply 0 missing 12606 Chassis power supply 1 missing 12607Power supply unit failed 12701 Loss of signal event 10102 Access to Escon card failed 10701 Access to Idprom failed 10702Access to card failed 10801 Access to Idprom failed 10802 Access to 2.5G card failed 11601 Access to Idprom failed 11602Access to card failed 11701 Access to Idprom failed 11702 Access to LRC failed 9201 Access to Idprom failed 9202Waveport 0 opt switch failed 9203 Waveport 1 opt switch failed 9204 HEC failure threshold exceeded 9978 Trunk laser failure detected 9504HEC degrade threshold exceeded 9979 Loss of signal event in Cisco OPT-MON-MIB 10302 Trunk laser shut down by laser safety control 10307Access to card failed 11101 Access to Idprom failed 11102 Optical Monitoring Alarms-ONS 15530 and ONS Rx ambient temp below low alarm threshold 14535 Tx ambient temp below low alarm threshold 14536Rx laser temp exceeds high alarm threshold 14546 Tx laser temp exceeds high alarm threshold 14547 CTM GateWay/CORBA Mapping-ONS 15600 Sonet BER threshold exceeded for signal degrade-line 17023 BER threshold exceeded for signal degrade-path 17024Far-end BER threshold passed for signal degrade-ring 17025 Far-end BER threshold passed for signal degrade-span 17026 Free running synchronization mode 17058 Stratum 3E fast start synchronization mode 17059Holdover synchronization mode 17060 Equipment fails to boot 17064 100 101 102 103 104 105 106 107 108 109 110 111 Control bus failure-I/O-TSC B 17576 Control bus failure-I/O-TSC a 17575112 113 114 115 116 Database backup failed 17751 Database restore failed 17752Isis adjacency failure 17753 Equipment high laser bias 17754 118 CTM GateWay/CORBA Mapping-ONS 15600 SDH 119 120 121 122 123 124 125 126 127 128 129 130 131 132 Eqpt problem on PIM or PPM 17725 Eqpt problem on carrier or PIM 17724133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148