Crestron electronic IPAC-GL1 Cresnet Wall Box Switches, Commercial Lighting Design Guide, Model

Commercial Lighting Design Guide Wall Box Dimmers and Switches

Cresnet Wall Box Switches

Model

Load

Features

CLW-SW

Wall Box

Switch

(Stand-alone)

CLW-SW1

Wall Box

Switch, Single

Button

(Stand-alone)

CLW-SWS1

Wall Box

Master Switch,

Single Button

(Master)

CLW-SLVS1

Wall Box Slave

Switch, Single

Button

(Slave)

CLW-SWS

Wall Box Master Switch

(Master)

CLW-SLVS

Wall Box Slave Switch

(Multipoint

Slave)

Supports incandescent and electronic low voltage loads up to 1000 watts, or magnetic low-voltage and neon/cold cathode loads up to 1000VA/750 watts. Fluorescent ballasts, high- intensity discharge lighting, and ceiling fans can also be switched.

Supports incandescent and electronic low voltage loads up to 1000 watts, or magnetic low voltage and neon/cold cathode loads up to 1000VA/750 watts.

Fluorescent ballasts, high- intensity discharge lighting, and ceiling fans can also be switched.

Supports incandescent and electronic low voltage loads up to 1000 watts, or magnetic low voltage and neon/cold cathode loads up to 1000VA/750 watts.

Fluorescent ballasts, high- intensity discharge lighting, and ceiling fans can also be switched

Supports incandescent and electronic low voltage loads up to 1000 watts, or magnetic low-voltage and neon/cold cathode loads up to 1000VA/750 watts.

1000 watt electronic light switch designed to mount in a standard electrical gang box

1000-Watt electronic light switch designed to mount in a standard electrical gang box

Large button provides instant on/off control of the load, while the small button turns the load off following a preset time delay. The slide switch selects between ADJUST, PRESET, and OFF modes. PRESET mode is the normal operating mode, and ADJUST mode is used for setting the delay time.

NOTE: The wall box switches do not support fan speed control. Use the CLX-1FAN4 for fan speed control.

Provides instant turn-on control of the load. Pressing the button again turns the load off following a preset time delay. The time delay can be overridden by tapping the button a second time, turning the load off instantly. The slide switch on the CLW-SW1 selects ADJUST, PRESET, and OFF modes. PRESET mode is the normal operating mode, and ADJUST mode is used for setting the delay time.

Multiple units may be ganged side-by-side along with other CLW-Series switches and dimmers or non-Crestron devices. The single large button on the CLW-SWS1 provides instant turn-on control of the load. Pressing the button again turns the load off following a preset time delay. The time delay can be overridden by tapping the button a second time, turning the load off instantly. The slide switch on the CLW-SWS1 selects ADJUST, PRESET, and OFF modes. PRESET mode is the normal operating mode, and ADJUST mode is used for setting the delay time.

One-gang wall mount slave switch designed for use with the CLW-SWS1 Wall Box Master Switch to provide multipoint switching control of a single load. The single pushbutton on the CLW-SLVS1 provides parallel functionality to that on the CLW-SWS1.

Serves as the master for multipoint switching control of a single load. Multi-point switching functionality (similar to

3-way or 4-way switching) is enabled by using the CLW- SWS with one or more CLW-SLVS Slave Switches. The large button on the CLW-SWS allows for instant on/off control of the load, the small button turns the load off following a preset time delay. The slide switch selects between ADJUST, PRESET, and OFF modes. PRESET mode is the normal operating mode, and ADJUST mode is used for setting the delay time.

NOTE: The wall box switches do not support fan speed control. Use the CLX-1FAN4 for fan speed control.

One-gang wall mount slave switch designed for use with the CLW-SWS Wall Box Master Switch to provide multipoint switching control of a single load. The pushbuttons on the CLW-SLVS provide parallel functionality to those on the CLW-SWS.

NOTE: In systems, only the master unit is connected to Cresnet®. Slave units are connected by the120V (Traveler) wire.

Doc 4775A 74