Resetting the system, Default system settings | DreamGEAR VSX-92TXH

Using other functions

Checking your system settings

Use the status display screen to check your current settings for features such as surround back channel processing and your current MCACC preset.

AUDIO	SUBTITLE		HDD	DVD
		DISP	CH	CH
PHOTO		T.DISP		STEREO/
STATUS	SIGNAL SEL		SBch	F.S.SURR
MULTI OPE		THX	STANDARD	ADV. SURR

SHIFT PHASE MCACC S.DIRECT

1 Press STATUS to check the system settings.

These appear on the front panel display.1

The front panel display shows each of the following settings for two seconds each:

Input source

↓

Surround Back Processing

↓

MCACC preset

↓

ZONE 2 / REC SEL

↓

ZONE 3

↓

HDMI Control

2When you’re finished, press STATUS again to switch off the display.

11

Resetting the system

Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.

1Switch the receiver into standby.

2While holding down the SETUP button on the front panel, press  STANDBY/ON.

The display shows RESET NO.

3Press the ENTER button on the front panel.

4Select RESET using /, then press the ENTER button on the front panel.

The display shows RESET? OK.

5Press ENTER to confirm.

OK appears in the display to indicate that the receiver has been reset to the factory default settings.

•Note that all settings will be saved, even if the receiver is unplugged.

Default system settings

Setting			Default
HDMI Audio			Amp

Digital Video Conversion			On

Speakers			A

Surround Back System			Normal (default)

Speaker System		Front	SMALL

		Center	SMALL

		Surr.	SMALL

		SB	SMALLx2

		SW	YES

Crossover	80 Hz

X-Curve	OFF

THX Audio Setting	0–1ft.

Inputs

See Input function default and possible settings on page 68.

MULTI-ZONE

Zone 2	Volume Type	Variable

Zone 2	Volume	-60

SR+

SR+ Control On/Off		OFF

SR+ Volume Control On/Off		OFF

Note

1 If the Pure Direct mode is switched on, some settings above will show OFF, even though they are on.

75

En

Image 75

DreamGEAR VSX-92TXH Using other functions Checking your system settings, Resetting the system, Default system settings

Contents

Operating Instructions Keep in a Secure AREA. this is for Your Security Federal Communications Commission Declaration of ConformityModel Number Responsible Party Name Important Safety Instructions Contents Controlling the rest of your system Other SettingsUsing other functions Hdmi Control Before you start Listening to Surround Sound Minute guideMinute guide Chapter Introduction to home theater Receiver outputs test tones to determine the speakers Speaker configuration in the OSDSwitch on the receiver and your TV Progress report is displayed on-screen while Select the input source you want to play Problems when using the Auto Mcacc SetupMinute guide Playing a source 02 5 minute guide Using Phase ControlPress Phase Phase Control to select Phase Control Phase Control indicator on the front panel lights Tweeter Midrange Woofer Using Full Band Phase ControlPress Phase Phase Control to select Fullband PHASE.3 Connecting your equipment Connecting your equipment ChapterRear panel Connecting your equipment When making cable connectionsAbout the video converter Connect using a standard video cable or an S-video cable Connecting your equipment Connecting your TV and DVD player VSX-94TXH Connecting a satellite/cable receiver or other set-top box For a second recorder, use the DVR/VCR2 in inputs Connecting a DVD/HDD recorder, VCR Connecting digital audio sources Use a three-way component video cableUse an optical cable for the connection This unit has an on-board Windows Media Audio Connecting analog audio sourcesConnecting a component to the front panel inputs About the WMA9 Pro decoder Surround Left Right Back left Back right Connecting your equipment Installing your speaker systemConnecting the speakers Front Left Right 10 mm 3/8 Bare wire connectionsPlacing the speakers Banana plug connections Assemble the stand as shown in the illustration.1 Connecting antennasTHX speaker system setup AM loop antenna AC outlet FM wire antennaConnecting external antennas Plugging in the receiver Input Selector dial Use to select an input source Controls and displaysControls and displays Chapter Front panel Controls and displays Operating range of remote control unit Controls and displays Display Select Controls and displays Remote controlRECEIVER Input Select SOURCE StatusMulti OPE Shift Auto playback Listening to your systemListening to your system Chapter Listening in surround sound Listening to your system Using the Home THX modesUsing the Advanced surround effects THX Games Mode Tip Using Front Stage Surround AdvanceUsing Stream Direct Listening in stereo Hdmi Digital Analog Choosing the input signalSelecting Mcacc presets While listening to a source, press Mcacc Mcacc Position Using the Virtual Surround Back mode Using the genre synchronizing function Using the tuner Using the tuner ChapterListening to the radio Abcdefghijklmnopqrstuvwxyz Using the tuner Saving station presetsNaming station presets Listening to station presets Select the setting you want to adjust System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menu Front Align System Setup menu If necessary, confirm the speaker configuration in the OSD.1 Select the surround back speaker setting Surround back speaker settingManual Mcacc setup Select ‘Surr Back System’ from the System Setup menu When youre finished, press Return Select ‘Manual MCACC’ from the System Setup menuSelect ‘Fine Ch Level’ from the Manual Mcacc setup menu Adjust the level of the left channel Standing Wave Select ‘Fine SP Distance’ from the Manual Mcacc setup menuSelect ‘Standing Wave’ from the Manual Mcacc setup menu Fine Speaker Distance Acoustic Calibration EQ Professional Acoustic Calibration EQ AdjustHow to use Acoustic Calibration EQ Professional How to interpret the graphical output Using Acoustic Calibration EQ Professional Select ‘EQ Professional’ then press EnterSelect an option and press Enter Full Band Phase Control Data Management Checking Mcacc preset dataSelect ‘FULL Band Phase CTRL’ from the System Setup menu Select ‘Data Management’ from the System Setup menu Copying Mcacc preset data Renaming Mcacc presetsClearing Mcacc presets Select ‘Speaker Setting’ from the Manual SP Setup menu System Setup menu Manual speaker setupSpeaker Setting Select ‘Manual SP Setup’ then press Enter Speaker Distance Channel Level Curve THX Audio Setting Other connections Chapter Connecting an iPodConnecting your iPod to the receiver Other connections Other connections Using XM RadioWatching photos and video content Connecting your XM Radio receiver Using XM HD Surround Saving channel presetsListening to XM Radio Listening to channel presets Using Sirius RadioUsing the XM Menu Connecting your Sirius Connect Tuner Press Sirius SHIFT+TUNER to switch to the Sirius input Listening to Sirius RadioSelecting channels and browsing by genre HDMI/DVI-compatible monitor or plasma display Connecting using HdmiUsing the Sirius Menu Sirius Menu provides additional Sirius Radio features.1 Use standard RCA/phono jack cables for the connections Connecting the multichannel analog inputsAbout Hdmi Selecting the multichannel analog inputs Select ‘Speaker B’ from the ‘Surr Back System’ menu Other connections Speaker B setupSwitching the speaker system Bi-amping your front speakers To bi-wire a speaker, connect two speaker cords to Connecting additional amplifiersBi-wiring your speakers Normal default or Speaker B in Surround back speaker Basic MULTI-ZONE setup Zone Surround Back System MULTI-ZONE setup ZoneMaking MULTI-ZONE connections For the zone you have selected Using the MULTI-ZONE controlsSecondary MULTI-ZONE setup Zone Use the Input Selector dial to select the source Input Connecting an IR receiverSwitching components on and off using the 12 volt trigger MULTI-ZONE remote controls DVD player Using this receiver with a Pioneer plasma display Connecting a PC for Advanced Mcacc output Connect your computer to the RS-232C jack onRear panel of the receiver Advanced Mcacc output using your PC Select ‘Output PC’ and press EnterPersonal computer Hdmi Control Hdmi Control ChapterMaking the Hdmi Control connections About Hdmi Control Hdmi Control Setting the Hdmi optionsSynchronized amp mode Before using synchronization Other Settings Other Settings ChapterInput Setup menu Other Settings Other Setup menuInput function default and possible settings Multi Channel Input Setup Zone Audio SetupSR+ Setup for Pioneer plasma displays You will return to the Other Setup menu OSD AdjustmentSelect the ‘PDP Volume Control’ setting you want Select ‘OSD Adjustment’ from the Other Setup menu Press Return to confirm and exit the menu Using other functionsUsing other functions Chapter Setting the Audio options Setting the Video options Using other functions Prepare the source you want to record Playing a different source when recordingMaking an audio or a video recording Select the source you want to record Dimming the display Reducing the level of an analog signalSwitching the speaker impedance Using the sleep timer Press Status to check the system settings Using other functions Checking your system settingsResetting the system Default system settings DSP Controlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Remote controls Controlling the rest of your system Erasing one of the remote control button settingsResetting the remote control presets Confirming preset codes Programming a multi-operation or a shutdown sequence Renaming input source namesMulti Operation and System Off Direct function Press Multi OPE Using multi operationsUsing System off Select the button for the command you want to input Controls for other components Controlling the rest of your system Controls for TVs Decide which component you want to use the remote sensor Operating other Pioneer components with this unit’s sensor Additional information Chapter TroubleshootingPower Additional information Additional information Other audio problems Video Phase Control feature Settings Professional Calibration EQ graphical outputDisplay 96 kHz Remote control No Music Track Hdcp Error shows in the displayError IPod messages Sirius radio messages XM radio messages Dolby Additional information Surround sound formats Windows Media Audio 9 Professional About THX About Neural Surround PRO Logic Stereo 2 channel signal formatsON/AUTO THX Cinema Dolby Digital Plus Straight decoding Multichannel signal formatsTHX Games Mode a XM Radio Auto DTS-ES b DTS-ES Matrix/Discrete DTS-ES+THX Matrix/DiscreteMovie a MOVIE+THX a Pro Logic llx Movie a Sacd Direct VSX-94TXH or Straight decoding VSX-92TXH Direct Pure Direct Cleaning the unit Additional information Specifications Additional information Our philosophy Features Information courtesy of the Deafness Research Foundation To establish a safe levelOnce you have established a comfortable sound level Decibel Level Example Pioneer Corporation