DreamGEAR VSX-94TXH Controlling the rest of your system, Resetting the remote control presets

12Controlling the rest of your system

4Point the two remote controls towards each other then press the button that will be doing the learning on this receiver’s remote control.

PRES KEY starts flashing to indicate the remote is ready to accept a signal.

•The remote controls should be 3 cm to 5 cm (1 to 2 inches) apart.

3 cm to 5 cm (1 to 2 inches)

5Press the corresponding button on the other remote control that is sending (teaching) the signal to this receiver’s remote control.

For example, if you want to learn the playback control signal, press and hold  briefly. The LCD display will show OK if the operation has been learned.1

If for some reasons the operation hasn’t been learned the LCD will display ERROR briefly and then display PRES KEY again. If this happens, keep pressing the (teaching) button as you vary the distance between the two remotes,

until the LCD display shows OK.2

Certain buttons represent operations that cannot be

learned from other remote controls.3 The buttons available are shown below (with the exception of the TV controls, a combination of SHIFT and these buttons can also be learned):

7Press and hold the RECEIVER button for a couple of seconds to exit and store the operation(s).

Erasing one of the remote control button settings

This erases one of the buttons you have programmed and restores the button to the factory default.

1While pressing the RECEIVER button, press SETUP. The remote LCD display shows SETUP.

2Use / to select ERASE then press ENTER.

The LCD on the remote prompts you for the component corresponding to the button setting to be erased.

3Press the input source button corresponding to the command to be erased then press ENTER.

The LCD display flashes PRES KEY.

4Press and hold the button to be erased for two seconds.

The LCD display shows OK or NO CODE to confirm the button has been erased.

5Repeat step 4 to erase other buttons.

6Press and hold the RECEIVER button for a couple of seconds when you’re done.

RECEIVER INPUT SELECT

CD CD-R

DVD	TV
	HOME MEDIA
DVR2	GALLERY

DVR1 i Pod

SLEEP

SR+

SYSTEM OFF

SOURCE

XM RADIO  HDMI

BD TVCTRL

SIRIUS  ZONE2/3

TUNER RECEIVER

DIMMER ANALOG ATT

GENRE

Resetting the remote control presets

This will erase all preset remote control preset codes and programmed buttons.

1	While pressing the RECEIVER button, press SETUP.
The remote LCD display shows SETUP.
2	Use / to select RESET then press ENTER.
RESET flashes in the LCD display.
3	Press and hold ENTER for about two seconds.
The LCD shows OK to confirm the remote presets have

						TV CONTROL
				TV VOL	INPUT		TV CH	VOL
					SELECT
D.ACCESS			CLASS
	CLEAR		DISC
	+10	CH	ENTER
		LEVEL		ANT		REC	INFO
A PARAMETER			V PARAMETER
								MUTE
TOP MENU 			MENU T.EDIT
	TUNE			MPX			REC STOP	MEMORY
BAND	ST		ST
	ENTER		 
SETUP			RETURN	AUDIO	SUBTITLE		HDD	DVD
PROGRAM TUNE						DISP	CH	CH
				PHOTO		T.DISP		STEREO/
CATEGORY	GUIDE			STATUS	SIGNAL SEL		SBch	F.S.SURR
	TV CONTROL

6To program additional signals for the current component repeat steps 4 and 5.

To program signals for another component, exit and repeat steps 1 through 5.

been erased.

Confirming preset codes

Use this feature to check which preset code is assigned to an input source button.

1While pressing the RECEIVER button, press SETUP. The remote LCD display shows SETUP.

2Use / to select READ ID then press ENTER.

The LCD on the remote prompts you for the input source button you want to check.

Note

1Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.

2• Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.

•If the remote LCD shows FULL, it means the memory is full. See Erasing one of the remote control button settings below to erase a programmed button you’re not using to free up more memory (note that some signals may take more memory than others).

3Note that the number key decimal button (+10/D.ACCESS) may not be learned with some components.

78

En