DreamGEAR VSX-94TXH, VSX-92TXH The System Setup menu, Follow the instructions on-screen

07The System Setup menu

3Connect the microphone to the MCACC SETUP MIC jack on the front panel.

Make sure there are no obstacles between the speakers and the microphone.

AUDIO	PARAMETER	VIDEO			MULTI – ZONE &	SIGNAL	SB ch	STEREO/
	(TUNE)				SOURCE/REC SEL
SPEAKERS			TUNER EDIT	BAND	CONTROL ON/OFF	SELECT	PROCESSING	F.S.SURR
PHONES				MCACC	VIDEO/GAME 2 INPUT
(ST)	ENTER	(ST)	USB	SETUP MIC

SETUP (TUNE) RETURN DIGITAL IN S-VIDEO VIDEO L AUDIO R

If you have a tripod, use it to place the microphone so that it’s about ear level at your normal listening position. Otherwise, place the microphone at ear level using a table or a chair.

4Follow the instructions on-screen.

•Make sure the microphone is connected.

•If you’re using a subwoofer, it is automatically detected every time you switch on the system. Make sure it is on and the volume is turned up.

•See Problems when using the Auto MCACC Setup on page 9 for notes regarding high background noise levels and other possible interference.

5Wait for the Auto MCACC Setup to finish outputting test tones.

A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present in your setup. Try to be as quiet as possible while it’s doing this.

•Do not adjust the volume during the test tones. This may result in incorrect speaker settings.

If no operations are performed for 10 seconds while the speaker configuration check screen is being displayed, the Auto MCACC Setup will resume automatically. In this case, you don’t need to select ‘OK’ and press ENTER in step 7.

DVD/LD		0.0dB	DVD/LD			0.0dB
1. Auto MCACC			1. Auto MCACC
Now Analyzing…	( 2/11)			CHECK
			Front	[ YES ]
			Center	[ YES ]
Environment Check			Surr	[ YES ]
Ambient Noise	[ OK ]		SB	[ YESx2]
Microphone	[	]	SW	[ YES ]
Speaker YES/NO	[	]
	:Cancel		10:Next		OK	:Cancel

If you see an error message (ERR) in the right side column (or the speaker configuration displayed isn’t correct), there may be a problem with the speaker connection. If selecting RETRY doesn’t work, turn off the power and check the speaker connections. If there doesn’t seem to be a problem, you can simply use / to select the speaker and / to change the setting (and number for surround back) and continue.

7Make sure ‘OK’ is selected, then press ENTER. A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum receiver settings for channel level, speaker distance, and Acoustic Calibration EQ.

DVD/LD	0.0dB	DVD/LD		- 55.0dB
1. Auto MCACC		1. Auto MCACC
Now Analyzing…		Now Analyzing…	( 6/11)
Subwoofer Check		Surround Analysis
		Speaker System	[ OK ]
		Channel Level	[ OK ]
		Speaker Distance	[	]
	:Cancel		:Cancel

•With error messages (such as Too much ambient noise! or Check Microphone) select RETRY after checking for ambient noise (see Problems when using the Auto MCACC Setup on page 9) and verifying the mic connection. If there doesn’t seem to be a problem, you can simply select GO NEXT and continue.

6 If necessary, confirm the speaker configuration in the OSD.1

The configuration shown on-screen should reflect the actual speakers you have.

Again, try to be as quiet as possible while this is happening. It may take 3 to 7 minutes.

•If you selected a Stand.Wave Multi-Pointsetup (in step 2), you will be asked to place the mic at the 2nd and 3rd reference points before finally placing it at your main listening position.

8The Auto MCACC Setup has finished! Press RETURN to go back to the System Setup menu.

DVD/LD- 55.0dB

5a. MCACC Data Check

1. Speaker Setting

2. Channel Level

3. Speaker Distance

4. Standing Wave

5. Acoustic Cal EQ

6. FULL BAND PHASE CTRL

ENTER:Next :Return

The settings made in the Auto MCACC Setup should give you excellent surround sound from your system, but it is also possible to adjust these settings manually using the

System Setup menu (starting on page 36).2

Note

1This screen is only shown if you selected ALL or Speaker Setting in Custom Menu from the Auto MCACC CUSTOM menu.

2• Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 5 inches (12 cm) will end up with different size settings. You can correct the setting manually using the Manual speaker setup on page 47.

•The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking delay and room characteristics into account) and generally does not need to be changed.

38

En